NexPow T11F Manuale utente
2022/07/20
Jump Starter & Power Bank
User Manual
Model: T11F
EN
ENGLISH MANUAL 1~12
…………………………………
DEUTSCHES HANDBUCH 13~24
………………………
MANUEL EN FRANÇAIS 49~60
…………………………
MANUALE ITALIANO 25~36
………………………………
MANUAL EN ESPAÑOL 37~48
……………………………
Catalogue
Friendly Tips:
Please carefully read the instruction manual and use
product correctly based on the instruction manual so
that you can be familiar with the product more
conveniently and quickly!
Perhaps there is small difference between the photo
and the actual product,so please turn to the actual
product for detail information.
Step 4:
After jump-starting the engine, remove
the battery clamp from the car battery,
then remove the clamp plug from the
jump starter.
When the indicator light of jumper cable is
solid green and blue, you can try to start
your vehicle.
Step 3:
Connect the clamp to the car battery.
Connect the red clamp cable to positive
and the black clamp cable to negative.
Please avoid reverse connection.
Connect the jumper cable to the jump
starter. If the indicator light of jumper
cable is solid blue, the clamp cable is in
standby status. Now the jump starter is
ready for jump-starting.
Step 2:
Step 1:
Operating Instructions:
Turn on the function button and make sure it is over 40% charged. If the power is less than 40%, it
may not be able to start your engine.
How to Start Vehicle When Battery is Flat?
Outdoor Travel
Flashlight
Apart from jump starting a car, this product can also supply power for a mobile
phone, PSP, MP3/MP4, camera and other consumer electronics, and with
different lighting modes.
Jump Start A
car Charge PSP Charge Cell
Phone/Tablet
Charge Camera
/Video
2) Connect the clamps to the vehicle battery. Red clamp to
positive polarity (+), black clamp to negative polarity (-).
3) Press the car start button or turn the ignition switch to the
START position.
4) This jumper cable is designed with advanced protection of
indicator light and buzzer.
The green light and the blue light
will be on.
It means the jumper cable connected to the
jump starter is correct and ready to connect
to the car battery.
After the car has started, remove the jumper
cable.
Smart Jumper Cable Instruction
The blue light is on.
It means all connection is correct, and you
can start the engine.
The blue light is on.
1) Connect the plug fully seated into the host.
How to Jump Start 12V Vehicle?
The red light is on, the blue lightis on, and
the beeps for a long time.
Jump starter power is low,
please recharge.
Reverse polarity connection,
please reconnect correctly.
The red and black clamps are
short-circuited,
please reconnect correctly.
Jumper cable over temperature
(≥65 ± 5℃),waiting to cool down
(≤55 ± 5℃)before the next start.
Notice:
• 1 light stands for 25% power.
When battery level is low, please charge the battery before using.
• Turn on the function button and make sure it is over 50% charged. If the
power is less than 50%, it may not be able to start your engine.
Power
Third step:
Second Step:
First step:
When our Mobile Phonies out of Power, How to Correctly
Charge it with the Jump Starter?
Output 1(2)
How can Led Emergency Light be Turned on?
Long press for 2 seconds in any mode to turn off the LED lamp function.
Press once
Press onceHold 2s
Lights out state Lighting mode SOS mode Warning mode
Press once
Input
When the Jump Starter is out of Power, How can We
Charge it?
First step: Second Step:
Insert the charging line
Type-C into the product
input port.
Insert the other side into the 220V(110V)
power, the indication light will be blicking,
which shows it is under charging.
Model: T11F
Start Current: 600A
Input: 5V/2A
USB Output 1: 5V/2.1A
USB Output 2: 5V/1A
Peak Current: 1000A
Circle Life: 1000 Times
Parameter:
Dimension: 152*84.6*33mm
Cpacity: 38.48Wh
Operating Temperature: -20 ~ +60℃
Indice
Lingue:
