Next DMX 512 Manuale utente
N
ext
USER’S MANUAL
GB
Wireless DMX 512 TRANSCEIVER
DMX
W
i
R
We congratulate you on your purchase of Wi DMX.
Before you proceed using this product, read this user’s manual carefully, as
it gives important information on safety, use and maintenance .
FRONT PANEL
GB
MODE
9V-DC IN
OUT
IN
DMX 512
12
DMX
Wi
N
ext
DMX 512 ch 40hZ
SET
OFFON
TERM.
12
3
4
5
6
7
Shows the state of transmission/receipt of the channel 1
Shows the state of transmission/receipt of the channel 2
LCD display, it shows all the informations on the Wi DMX functions.
MODE key
SET key
DOWN key
UP key
1
2
3
4
5
6
7
Setting of the equipment
1.1
Unpack WI DMX
1.2
Acessories and documentation provided with the equipment
Description of the side panel and installation
2.1
Description of the side panel
2.2 Making a DMX 512 signal cable
2.3
Input connection for power supply
2.4
Connection of the ac-adapter to main AC
Initial setting
3.1 Setting of the operating mode
Use of the equipment - operating modes
4.1
TRANSMITTER
mode
4.2 Setting of
Tx1
4.3
LED 1
function
4.4 Setting of
Tx2
4.5
LED 2
function
4.6 Receiver PAIRING
5.1
RECEIVER
mode
5.2 State of
Rx1
5.3
LED 1
function
5.4 State of
Rx2
5.5
LED 2
function
5.6 Pairing with Transmitter (GET PAIRING)
5.7 Pairing with Transmitter (GET PAIRING) using Wi D PEN
6.1
EXTENDER
mode
6.2 Setting of
Tx1
6.3
LED 1
function
6.4 Setting of
Rx2
6.5
LED 2
function
6.6 Receiver PAIRING
6.7 Pairing with Transmitter (GET PAIRING)
6.8 Pairing with Transmitter (GET PAIRING) using Wi D PEN
7.1 TX BACKUP mode
INDEX
Open the box; Remove the ac-adapter and the documentation.
Take the equipment out of the box as shown in the picture below.
1.1 UNPACK WI-DMX
1.2
ACESSORIES AND DOCUMENTATION PROVIDED WITH THE EQUIPMENT
Verify the contents of the packing.
If one of the following parts of the packing is missing or damaged, please,
contact your dealer immediately.
• Wi DMX
• User’s manual.
• Warranty
• Ac-adapter mod.1814807
• 1 XLR 3/5 P male connector
• 1 XLR 3/5 P female connector
Read the following warnings before beginning installation.
• This unit is not intended for home use.
• Read this manual thoroughly and observe the following precautions before working
with the Wi DMX.
• Take care not to spill liquids on to the controller and do not use it in excessively humid
conditions.
• Do not install Wi DMX near heat sources or expose it to direct sunlight and do not
install in dusty environments without suitable protection.
• Do not use Wi DMX unless the ac-adapter cable and plug are in perfect condition
(replace or repair if necessary).
• Do not use solvents such as acetone or alcohol to clean the controller or the finish
and panel lettering will be damaged.
• If a fault occurs, consult your nearest service centre or a specialized light equipment
repair service. Do not attempt to repair the controller yourself.
15
3
42
15
3
42
2.1 DESCRIPTION OF THE SIDE PANEL
1
Standard DMX 512 signal OUTPUT with a 3/5-pole cannon connector.
2
Standard DMX 512 signal INPUT with a 3/5-pole cannon connector.
3DMX TERMINATOR
1 2
3
2.2
MAKING A DMX 512 SIGNAL CABLE
Wi DMX has a DMX 512 input/output that uses standard XLR 5-pin or XLR 3-pin
connectors.
The connection must be put into practice with shielded cable by these characteristics:
- 2 conductors + shield
- 120 Ohm impedance
- low capacity
- maximum transmission rate 250 Kbaud.
For the connection refer to the underlying picture
ATTENTION: the shield of the cable must never be connected to the ground of the
electrical system as this could cause faults during the working of the Wi DMX.
15
3
42
Common
DMX
-
DMX
+
XLR 5-pin
1
3
2Common
DMX
-
DMX
+
XLR 3-pin
2.3 INPUT CONNECTION FOR POWER SUPPLY
2.4 CONNECTION OF THE AC-ADAPTER TO THE MAIN AC
Plug the connector of the ac-adapter completly in the power input
To disconnect it, extract gently.
ATTENTION: do not use ac-adapters different from the one supplied, it
could cause serious damages at the internal circuitation.
4
MAKE SURE THAT VOLTAGE AND POWER FREQUENCY CORRESPOND TO
WHAT IS REPORTED ON THE AC ADAPTER PLATE.
The supplied ac-adapter has a plug, therefore you should only plug it in the
socket.
When Wi DMX is powered, on display
appears as in (Fig.1),if this condition is not
true, please check if there is power in the
electric socket or check the connection
between ac-adapter/controller and ac-adapter/electric socket.
If the problem persist, please consult your dealer.
4
WIRELESS
Fig. 1
N
ext
SET
This procedure allows to change between
TRANSMITTER -
RECEIVER - EXTENDER - BACKUP
mode of operation
.
-Power down the Wi DMX.
-While holding down
SET key
(Fig.2),
Power up the Wi DMX.
REGARDLESS OF THE MODE, YOU MUST EXECUTE THE PAIRING OPERATIONS
EXPLAINED IN THE RELATIVE CHAPTERS OF THIS MANUAL
The WWiiDDMMXXfactory default mode is TTRRAANNSSMMIITTTTEERR
On display appears as in (Fig.3).
Use UP/DOWN keys to change operating
mode.
Confirm with SET key
(Fig.2).
Fig. 2
3.1
SETTING OF THE OPERATING MODE
The connection must be like in (Fig.4)
WWiiDDMMXXanalyzes the DDMMXX551122signal as soon as the
XLR connector is inserted and shows the number of
channels generated from the controller (Fig.5);
in absence of signal the display appears like in (Fig.6).
This operation mode allows you to transmit the DMX 512 signal coming from a con-
troller to the paired receivers, through two channels of transmission.
4.1 TRANSMITTER MODE
CFG
:
TRANSMITTER
Fig. 3
dmx
:
512ch, 40hz
Fig. 5
dmx
:
<<no data>>
Fig. 6
15
3
42
15
3
42
DMX coming
from controller
DMX to other
projectors
Fig. 4
Indice
