4SETTING UP YOUR DEVICE
Plug in the Power Adapter into the device labeled
Wireless Bridge 1 and press the Power Button to the
ON position (IN).
Note: Wireless Bridge 1 should already be set to AP mode. If it is not,
please slide the AP/Station Switch to the upward position.
Connect Wireless Bridge 1 to your Network Device
(Gateway, Router, etc.) with an Ethernet (RJ-45) cable.
You can use either Ethernet ports of the Wireless
Bridge to make this connection.
Setup Wireless Bridge 1 Setup Wireless Bridge 2
B
Setup Wireless Bridge 2 closest to the location of the
Internet Enabled Device. Plug in the power adapter
and press the Power Button to the ON position (IN).
Connect Wireless Bridge 2 to an Internet Enabled
Device (Computer, Console, etc.) with an Ethernet
(RJ-45) cable.You can use either Ethernet ports of
the Wireless Bridge to make this connection.
Note: Wireless Bridge 2 should already be set to Station mode. If it is
not, please slide the AP/Station Switch to the downward position.
Setup via WPS (WiFi Protected Setup)
C
Press and release the WPS button on Wireless Bridge 1 and
the WPS LED will start to blink GREEN.
Within two minutes press and release the WPS button on
Wireless Bridge 2 and the WPS LED will start to blink GREEN.
AP
Station
WPS
WiFi
ETH 2
ETH 1
Power
AP
Station
WPS
WiFi
ETH 2
ETH 1
Power
Wireless Bridge 1 Wireless Bridge 2
Reset
WPS
Client
AP
ETH2
ETH1
On/Off
Power
Station
AP
Internet-Enabled Device
(Computer, Console, etc.)
Ethernet Cable
Wireless Bridge 2
Upon successful connection, the WPS LED and WiFi LED will
light up solid GREEN on both of the Wireless Bridges.
Repeat steps 3-7 to add additional station devices.
Please refer to Section E for troubleshooting if the devices are not working properly.
Reset
WPS
Client
AP
ETH2
ETH1
On/Off
Power
Station
AP
Network Device
(Modem, Router, etc.)
Wireless Bridge 1
Ethernet Cable
Congrats! Your devices are ready for
ultra-fast streaming and gaming!
D
AP
Station
WPS
WiFi
ETH 2
ETH 1
Power
AP
Station
WPS
WiFi
ETH 2
ETH 1
Power
INTERNET Wireless Bridge 1
Wireless Bridge 2
End Device
Troubleshooting |
EThe following information should help you diagnose basic setup or installation problems.
POWER Indicator is OFF - If the Power LED goes off, please make sure that your power outlet is
working properly (perhaps by testing with another device). Then, plug in your WB-1750 again and
make sure to press the Power Button to the ON position (IN).
ETHERNET LED is OFF - If the ETHERNET LED fails to light up, check that the LAN port of the
:%XQLWLVFRQQHFWHGUPO\WRWKH/$1SRUWRIWKHRWKHUGHYLFH7RFKHFNWKHFRQGLWLRQRIWKH
Ethernet cable, use another cable to test the same connection.
WPS LED is OFF - If the WPS LED(s) fails to light up, press and release the WPS Button on Wireless Bridge 1.
Within two minutes press and release the WPS Button on Wireless Bridge 2 (during this time both WPS
LEDs will blink). Upon successful connection the WPS LEDs will light up solid GREEN on both of the
Wireless Bridges.
AP LED is OFF - Wireless Bridge 1 is in Station Mode. Set Wireless Bridge 1 to AP Mode by sliding the
AP/Station Switch to the up position.
STATION LED is OFF - Wireless Bridge 2 is in AP Mode. Set Wireless Bridge 2 to Station Mode by
sliding the AP/Station Switch to the down position.
RESET - If you have tried the above and are still experiencing problems, you can reset both devices to
factory default by using a pin to push in the Reset Button for more than 5 seconds, then release the button.
For instructions on advanced features,
FAQ, etc., please visit our website or give
us a call!
?NEED MORE HELP?
Remember to connect with us on social media for
product updates, giveaways, and new releases!
http://nexuslinkusa.com/support
Support: (855) 313-4433
facebook.com/nexuslinkusa
youtube.com/nexuslinkusa
instagram.com/nexuslink_us
twitter.com/nexuslinkusa
We’re Here to Help!
