Nickel-Electro Clifton Range CM-1 Manuale utente
High quality products at aordable prices
CYCLONE VORTEX MIXER
CM-1
CYCLONE MIXER CM-1
CLIFTON RANGE® - 3 YEAR WARRANTY
2
Dear Customer
The Clifton Range® is part of Nickel-Electro Ltd a family rm based in Weston-Super-
Mare which was incorporated as a limited company in 1941 but its roots can be traced
back to 1935 when the business rst started. Now in its 3rd generation of family
members, the company prides itself on being a strongly established, independant
British manufacturer.
Thank you for purchasing this piece of Clifton Range® equipment. To get the best
performance from your equipment and for your own safety please read these
instructions carefully before use.
GENERAL NOTES
1. This product is designed for laboratory use only. Always follow good laboratory
practice.
2. If this product is not used in accordance with these instructions then basic safety
protection may be aected.
3. The mains supply cord tted to this product is heat resistant and should be
replaced with an equivalent type by a qualied electrician.
4. Ensure that the power supply has a safety earth (ground) terminal.
5. Connect to a mains power supply with RCD protection if possible.
6. Ensure that the mains switch and power supply connector are accessible during
use.
7. Before using any cleaning or decontamination method please refer to the
Maintenance and Cleaning section to ensure the proposed method will not
damage the unit.
8. Connect only to a power supply with the corresponding voltage to that specied
on the rating label positioned on the rear of the unit.
9. Over voltage category II (IEC 644) and Pollution Degree 2 (IEC 644).
10. WEAR SAFETY GOGGLES WHEN MIXING.
CYCLONE MIXER CM-1
CLIFTON RANGE® - 3 YEAR WARRANTY
3
!
!
LOCATION
The product must be placed on a smooth, level and sturdy work surface. Suitable for use
in ambient temperatures 5°C to 40°C with a maximum humidity 80% (temperature 31°C)
decreasing to 50% (temperature 40°C). Mains voltage uctuations are not to exceed +/-
10˚% of the nominal supply.
UNPACKING
Remove the product from its packaging and retain over the warranty period. Contents
consist of:
• Cyclone vortex mixer
• Power lead
• Instruction manual
Fit the power lead into the socket at the rear.
SAFETY
Do not touch any electrical contacts or open any closure panels.
RISK OF ELECTRIC SHOCK!!
POWER LEAD AND CONNECTION TO ELECTRICAL SUPPLY
Check the electrical supply is compatible with the rating label.
IF IN DOUBT CONSULT AN ELECTRICIAN. THE PRODUCT MUST BE
EARTHED!
Where the mains supply or plug connection diers refer to local
regulations or consult an electrician.
OPERATING INSTRUCTIONS
1. Switch the cyclone mixer ON using the green rocker switch. The switch will
illuminate.
2. The mixing speed can be varied by turning the dial anticlockwise to decrease or
clockwise to increase the mixing intensity.
3. When placing the tube for mixing onto the Cyclone’s rubber cup always select a
slow speed and gradually adjust the dial to produce the desired vortex.
4. The Cyclone mixer can be operated in two ways - manually or automatic.
MANUAL MODE: press start operation providing instant action the
moment the tube is pressed into the rubber cup.
AUTOMATIC MODE: the rubber mixing cup rotates continuously.
CARE AND MAINTENANCE
Please ensure that the washing agent and sanitizing agent are BSI accredited and
approved by the H&S department for use on laboratory equipment and stainless steel
within your laboratory.
DISCONNECT THE MIXER FROM THE POWER SUPPLY PRIOR TO
CLEANING
Only use a damp cloth and mild detergent to wipe clean the outside surfaces.
Disconnect the unit from the mains electrical supply before cleaning. Ensure the unit is
completely dry.
PORTABLE APPLIANCE TESTING
These tests should be conducted by a qualied person.
DO NOT PAT test the boiling bath unless it contains water.
DO NOT Flash Test!!
CYCLONE MIXER CM-1
CLIFTON RANGE® - 3 YEAR WARRANTY
4
!
!
!
oc
CYCLONE MIXER CM-1
CLIFTON RANGE® - 3 YEAR WARRANTY
5
WARRANTY TERMS AND CONDITIONS
1. Nickel Electro Ltd warrants to the Customer that the product purchased is free
from defects in materials and workmanship.
2. Provided the terms of payment are duly complied with, Nickel Electro Ltd
undertakes to remedy any original defects arising from faulty materials or
workmanship, in any goods manufactured/supplied by Nickel Electro Ltd, which
under proper and normal conditions of use, may develop within a period of three
years from the date of delivery.
3. In the case of components which by their nature of application have an
unpredictable life, this guarantee shall only be to the extend of the guarantee
given by the manufacturers of these articles.
4. Nickel Electro Ltd will accept no liability, where in the opinion of the company
the defect has been caused by damage due to the Customers failure to follow
operating instructions, correct installation, wear and tear, or damage due to the
use of spare parts other than those spare parts of Nickel Electro Ltd or which are
recommended by Nickel Electro Ltd, the defect has been caused by alterations or
repairs being undertaken by a person(s) other than an authorised representative of
Nickel Electro Ltd.
5. Any damage claim must be in writing, and give the serial number and description
of the goods, order number and date of delivery, and will not apply where any
names or serial numbers or other information which may be attached to or
inscribed upon the goods have been removed, covered up or defaced in any way.
6. Any goods or parts thereof, which may require repair or replacement, shall be
repaired or replaced (at the discretion of Nickel Electro Ltd) at the works of Nickel
Electro Ltd. The product to be repaired shall be delivered carriage paid back to
Nickel Electro Ltd by the customer at the Customer’s risk and expense. Any such
goods or parts will be delivered by Nickel Electro Ltd to the Customer free within
the United Kingdom but if required to be borne by the Customer. All faulty parts
removed from the equipment will become Nickel Electro Ltd’s property. Any
other repairs or work by Nickel Electro Ltd will be carried out under the terms and
conditions for specialist engineers currently in force.
7. In the event of replacement with a new or reconditioned model, the replacement
unit will continue the warranty period of the original equipment.
8. If any goods or parts thereof are returned unnecessarily all cost involved, including
a charge for inspection, handling and the return carriage must be paid by the
sender. In no circumstances shall any of the goods be returned to Nickel Electro Ltd
without its prior written consent.
9. Please retain the original packaging over the warranty period.
EC Declaration of Conformity
We herewith conrm the following product:
Cyclone Vortex Mixer: CM-1
Conforms with the requirements outlined by the following European Directives:
Low Voltage Directive 2006/95/EEC
EMC Directive 2004/108/EEC
Conforms with the requirements of the following standards:
BS EN 61010:1
BS EN 61010:2.010
Safety requirements for electrical equipment for measurement, control and
laboratory use
BS EN 61326
Electrical equipment for measurement control and laboratory use - EMC
requirements
Designed and Manufactured in the UK by:
Nickel Electro Limited
Oldmixon Crescent
Weston super Mare
North Somerset BS24 9BL
t 01934 626691
f 01934 630300
w www.nickel-electro.co.uk
e [email protected].uk
CYCLONE MIXER CM-1
CLIFTON RANGE® - 3 YEAR WARRANTY 6
FINAL INSPECTION AND ELECTRICAL SAFETY TEST REPORT
BX0633 Issue 6: July 2015
Indice
