Nilfisk-Advance SH SOLAR E Manuale utente

SH SOLAR E, D

Instructions for use

107319182 i (09.2020)

EN-DE-FR-NL-ES-IT-RU-HU-TR-PL-CS

Printed in Hungary

Instructions for use ........................................................................................................... 3 - 32

Betriebsanleitung.............................................................................................................. 33 - 62

Manuel d’Instructions........................................................................................................ 63 - 93

Gebruikershandleiding...................................................................................................... 94 - 123

Manual de instrucciones................................................................................................... 124 - 154

Manuale di istruzioni......................................................................................................... 155 - 184

Руководство..................................................................................................................... 185 - 214

Üzemeltetési útmutató...................................................................................................... 215 - 242

Kullanma talimatları.......................................................................................................... 243 - 272

Instrukcje dotyczące obsługi............................................................................................. 273 - 302

Návod k obsluze............................................................................................................... 303 - 332

SH SOLAR E, D

Original Instructions

Index

1 Safety Precautions and Warnings ................................................................................................4

2 Description .....................................................................................................................................5

2.1 Application................................................................................................................................5

2.2 Operation elements ..................................................................................................................5

3 Installation ......................................................................................................................................5

3.1 Temperature conditions ............................................................................................................5

3.2 Condition of distance................................................................................................................6

3.3 Mounting of feet and levelling of machine ................................................................................6

3.4 Mounting of handle...................................................................................................................6

3.5 Mounting of spacers .................................................................................................................6

3.6 Water connection......................................................................................................................7

3.7 Mains power connection...........................................................................................................7

3.8 High pressure connection ........................................................................................................8

3.9 Venting (D models) ...................................................................................................................9

3.10 Venting - E models ................................................................................................................10

3.11 Connecting to external fuel supply – D-models .....................................................................11

4 Operation ......................................................................................................................................12

4.1 Connections............................................................................................................................12

4.2 Operation................................................................................................................................15

5 Fields of Application and Working Methods..............................................................................19

5.1 Fields of application................................................................................................................19

5.2 Working pressure ...................................................................................................................19

5.3 Temperature ..........................................................................................................................19

5.4 Mechanical impact..................................................................................................................19

5.5 Detergents..............................................................................................................................20

5.6 Working methods....................................................................................................................21

5.7 Typical cleaning tasks.............................................................................................................22

6 Maintenance .................................................................................................................................23

6.1 Hour counters.........................................................................................................................24

6.2 Oil ...........................................................................................................................................24

6.3 Water ﬁlter ..............................................................................................................................25

6.4 Cleaning of high pressure nozzle ...........................................................................................25

6.5 Fuel ﬁlter - D-models only.......................................................................................................25

6.6 Disposable waste ...................................................................................................................25

7 Trouble Shooting..........................................................................................................................26

7.1 General trouble shooting - all models.....................................................................................26

7.2 Errors messages, E (electrical heated) models......................................................................27

7.3 Error messages, D (diesel heated) models ............................................................................29

8 Technical Data..............................................................................................................................30

9 Warranty........................................................................................................................................32

SH SOLAR E, D

Original Instructions

1 Safety Precautions and Warnings

Symbols used to mark

instructions

Before using the

high-pressure

washer, be sure

to also read the

enclosed opera-

ting instructions and keep them

within reach at all times.

Safety instructions

in these operating

instructions which

must be observed

to prevent risks to persons are

marked with this danger sym-

bol.

This symbol is

used to mark sa-

fety instructions

that must be ob-

served to prevent

damage to the

machine and its performance.

This indicates tips

and instructions to

simplify work and

to ensure safe operation.

High Pressure Washer -

SAFETY INSTRUCTIONS

SH SOLAR E, D

Original Instructions

3 Installation

3.1 Temperature conditions The machine should be in-

stalled in a frost-free room.

This applies to pump as well as

pipelines incl. of outlet points.

If connected to outdoor outlet

points it should be possible to

close and empty that part of the

line which is exposed to frost.

The maximum ambient tempe-

rature for the machine is 40°C.

2 Description

2.1 Application This high pressure hot water

washer has been developed

for stationary installation and

professional use within:

- agriculture

- light industry

- transport

- building and construction

- service

Section 4 describes how to use

2.2 Operation elements See illustration at the end of the manual

1 High pressure outlet (quick coupling, male)

2 Main switch

3 Start push button (illuminated, green)

4 Stop push button (illuminated, red)

5 Heating ON/OFF push button (illuminated, yellow)

6 Pressure gauge

7 Water inlet (quick coupling, female)

8 Thermostat (temperature adjustment)

9 Electric cable

10 Inspection window (hour counters, error messages)

11 Overheat fuse - resetable

12 Chimney

the high pressure hot water

washer.

Only use the high pressure

hot water washer for purposes

described in this manual.

The safety precautions must be

observed to prevent damage

to the machine, the surface to

be cleaned or severe personal

injuries.

Max 40 °C

Min 2 °C

SH SOLAR E, D

Original Instructions

3.2 Condition of distance In consideration of the cooling

system of the machine and the

accessibility of service, there

must be free wall space on both

sides of the machine. To the

right 500 mm at a minimum and

to the left 150 mm at a mini-

mum. To the ceiling there must

be at least 1000 mm and from

the rear point of the machine to

the back wall there must be at

least 100 mm. There must not

be any other objects in this area

either, such as pipes etc.

3.3 Mounting of feet and

levelling of machine mount the 4 feet by fastening

them to the ﬂange underneath

the machine by means of a 19

mm open-end wrench.

Place the machine on a plane

ﬂoor.

To level the machine, loosen

the lock nut on the appropriate

feet and adjust the height by

screwing the foot up or down.

Next cross-tighten the lock nuts

around the ﬂange. It is impor-

tant that all 4 feet are in contact

with the ﬂoor.

3.4 Mounting of handle

Min. 500 mm

Min. 150 mm

The machine is delivered

without feet mounted. Loosen

the machine from the pallet and

Mount the enclosed handles on

the machine by pressing them

into the suitable openings in the

cabinet.

3.5 Mounting of spacers Mount the enclosed spacers at

the back of the machine.

SH SOLAR E, D

Original Instructions

3.7 Mains power connection

CAUTION! An authorized elec-

trician must perform the electri-

cal connection of the machine

to the main power supply. Refer

to section "1 Safety precau-

tions and warnings".

The following precautions must

be observed:

• Make sure that the supply

cable is of the correct dimen-

sion (see voltage and load on

the data plate of the machine)

and is suitable for the speciﬁc

environment.

106420051

MITSUBISHI

+101

237

58912

Pump plc

13 14 15

F 10

135L1 L2 L3

T22T1 4 6T3

3.6 Water connection that the water supply is within

the following speciﬁcations and

that the water does not contain

particles such as ﬂoating sand.

Min. water inlet pressure: 1 bar

(at the required ﬂow rate of the

machine - see data plate.

Max. water pressure: 10 bar

Max. water inlet temp. (EH/GH):

85°C.

Max. water inlet temp. (D/G):

30°C.

All machines feature a water

tank, and no further protection

against back-ﬂowing water into

the supply network is required.

The machine complies with EN

1717.

If there is a risk of ﬂoating sand

or other impurities in the inlet

water, a sand ﬁlter (50 micron)

should be mounted between the

supply outlet and the internal

ﬁlter of the machine.

Clean the water inlet ﬁlter (7)

once a month or in case of

poor throughput (inlet pressu-

re below 1 bar at the ﬂow rate

required by the machine).

The water connection is made

through a ﬂexible hose connect-

ed to the quick coupling on the

water inlet (7) of the machine.

Make sure that the supply

hose is suited for the purpose

(temperature and ﬂow rate). If

in doubt, contact your Nilﬁsk

representative.

The connection can be made to

a public drinking water supply

network or a private water sup-

ply. A shut-off cock should be

mounted on the water supply

network in the immediate vicini-

ty of the machine. Make sure

SH SOLAR E, D

Original Instructions

• Guide the supply cable

through the strain relief grom-

met on the frame (9) and

through the strain relief grom-

met on the electric box into

the electric box.

• Connect the phase cords of

the supply cable to the con-

nection terminals L1(1), L2(3)

and L3(5) of the main switch

of the machine. For single

phase machines use L1(1)

and L2(3) to connect phase

and zero cords.

• Connect protective earth

wire to the terminal marked

and located above the main

switch on the metal chassis

(6). Ensure the connection by

the use of toothed washers.

• Check and measure the

protective earth connection

according to legislation.

• Connect the other end of the

cable to an approved socket

of a correct dimensioned

main supply.

Make sure that the cable is

properly guided and relieved

between the ﬁxed installation

and the machine and that the

cable is without any damage to

the insulation.

Also see notes in section "1

Safety precautions and war-

nings"!

3.8 High pressure connec-

tion

The outlet of the machine (1)

can be connected directly to a

standard high pressure hose (a)

or to a pipeline with ﬁxed outlet

points (c).

IMPORTANT: When connecting

to a pipeline always use a ﬂex-

ible hose connection from the

outlet of the machine (pos. 1).

Contact your Nilﬁsk distributor

for further information about

hose dimension.

It is recommended to let a ser-

vice technician authorized by

Nilﬁsk prepare the pipeline.

SH SOLAR E, D

Original Instructions

3.9 Venting (D models) When the machine is properly

connected to supply water,

electrical installation and a high

pressure hose (or pipeline) the

high pressure pump must be

vented before it is operational.

1.Turn the main switch, (2)to

position “ON”.

2.Push the “START” button (3),

and the machine will start.

3.Open the outlet point (spray

handle on high pressure

hose, (d) or outlet on piping

system (e) without having a

spray lance connected.

4.Let the water run until all air

has escaped from the pump

(even water ﬂow).

5.In the case of a recently

installed piping system, or if

the pipeline and the pump

have been emptied in any

other way, the system should

be vented by starting the

pump and then letting the

water run at each outlet point

of the pipeline at turns. It is

recommended to begin with

the most distant outlet (height

and/or length).

6.When connecting the high

pressure hose directly to the

machine, starting the pump

and activating the trigger

of the spray handle without

having attached the spray

lance, you should vent the

system.

7.Stop the machine by pressing

the "STOP" push button (4).

The machine is now vented.

SH SOLAR E, D

Original Instructions

3.10 Venting - E models When the machine is properly

connected to supply water,

electrical installation and a high

pressure hose (or pipeline) the

high pressure pump must be

vented before it is operational.

1.Turn on the water inlet and

wait until the water tank has

been ﬁlled with water.

2.Turn the main switch (2), to

position "ON".

3.Otherwise push the “START”

button (3), and the machine

will start.

4.Open the outlet point - spray

handle on high pressure

hose, (d) or outlet on piping

system (e) without having a

spray lance connected.

5.Let the water run until all air

has escaped from the pump

(even water ﬂow). If little or no

water ﬂows from the sys-

tem, it may be necessary to

vent the internal feed pump

separately. The Nilﬁsk service

technician should perform

this by loosening the centre

screw on the feed pump, see

arrow.

6.In the case of a recently in-

stalled piping system, or if the

pipeline and the pump have

been emptied in any other

way, the system should be

vented by starting the pump

and then letting the water run

at each outlet point of the

pipeline at turns. It is recom-

mended to begin with most

distant outlet (height and/or

length).

7.When connecting the high

pressure hose directly to the

machine, starting the pump

and activating the trigger of

the spray handle without hav-

ing attached the spray lance

should vent the system.

8.Stop the machine by pressing

the “STOP” push button (4).

The machine is now vented.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Nilfisk-Advance Rondella

Nilfisk-Advance

Nilfisk-Advance SH TRUCK Manuale utente

Manuali Rondella popolari di altre marche

Tricity Bendix

Tricity Bendix AW 1000 W Guida del prodotto

Panasonic

Panasonic NA-F60L5WRB Manuale utente

GE WSLP1500 Manuale

Electrolux

Electrolux EWF1284EDW Manuale utente

Bosch

Bosch WAN2829BSN Manuale utente

LG TV2516DV3B Manuale utente

LG TH2517DSAV Manuale utente

VESTEL

VESTEL CMH-XL 7510 TE Manuale utente

AEG

AEG 74335 Manuale operativo

Johnson

Johnson JWF721A Manuale utente

Beko

Beko WTE7604XLW0 Manuale utente

Danby

Danby DTT100A1WDB Istruzioni per il montaggio

Amica

Amica WA 14 Ex Manuale utente

Daewoo

Daewoo DWD-F1222 Manuale utente

Bosch

Bosch WAS28461AU Manuale utente

Miele

Miele PW 6080 Vario Manuale utente

Finlux

Finlux FLX108CF220 Manuale utente

Whirlpool

Whirlpool 3LBR5132AN0 Manuale utente