NN STINGER CS58 Manuale utente
!
PLEASE READ!
This manual contains important information about product safety.
www.nationalnail.com
•Operation •Maintenance •Safety •Warranty
CS58 CAP STAPLER
OWNER’S MANUAL
Revised 12/10/07
www.nationalnail.com
TABLE OF CONTENTS
• Important Information 1
• Warnings 2
• Tool Specifications 5
• Loading the Tool 6
• Operating the Tool 7
•STINGER™ CS58 Schematic 9
•STINGER™ CS58 Parts List 10
• Maintenance and Storage 13
• Warranty 14
• Troubleshooting 15
www.nationalnail.com
IMPORTANT INFORMATION
Please take the time to read and understand the information contained in the Owner’s Manual
included with this product before operating or maintaining the STINGER™ CS58 Cap Stapler.
Improper use of this tool could result in serious injury or even death. Most accidents occur
because of the failure to observe basic safety rules and precautions. Basic safety precautions are
outlined in the “Warnings” section of this manual.
This product is intended for securing housewrap and roofing felt only. Please do not use this
pneumatic tool for applications other than those specified.
This manual should be available for anyone who plans to operate the tool.
1
www.nationalnail.com
WARNINGS
!
2
PERSONAL SAFETY ITEMS
• Do not use tool prior to reading the Owner’s Manual.
• Always wear eye protection that conforms to ANSI requirements (Z87.1) and
provides protection against flying particles both from the front and side. Eye
protection should be worn by the operator and by others in the work area. Eye
protection is required to protect against flying fasteners and debris that could
possibly cause severe eye injury.
• The employer is responsible to enforce the use of eye protection equipment by the tool
operator and all other personnel in the work area.
• To prevent accidental injuries:
– Handle the tool with care
– Always assume that the tool contains fasteners
– Always disconnect the air hose from the STINGER™ CS58 when:
• loading staples and/or caps
• performing inspection, maintenance or repair
• clearing a staple or collated cap jam
• the tool is not in use
• leaving the work area
• moving the STINGER CS58 to another work location
• handing the STINGER CS58 to another person
• storing the tool
– Never point the tool toward yourself or anyone else
– Never engage in horseplay
– Never hold or carry the tool with a finger on the trigger
– Never place a hand or any other part of the body in the fastener discharge area of
the tool while the air supply is connected
www.nationalnail.com
WARNINGS
AIR SUPPLY AND CONNECTIONS
• Use only clean, regulated compressed air as a power source for this tool. Do not use bottle
gases, combustible gases or oxygen as a power source for the tool as the tool may explode.
• Do not use air supply pressures that exceed 105 PSI.
• Do not exceed the recommended maximum operating air pressure as tool wear will be greatly
increased. The air supply must be capable of maintaining the operating air pressure of the tool.
Pressure drops in the air supply can reduce the tool’s driving power.
• Use a pressure regulator and gauge to allow visual inspection of the air pressure being
delivered to the tool.
• Use air hoses that have rated pressures of up to 150% of the maximum pressure that can be
generated by the power source. The supply hose should contain fittings that will provide quick
disconnecting from the male plug on the tool.
• Use quick connect fittings that allow the tool to be unhooked from the air supply quickly and
easily.
• Do not use fittings that will not allow the tool to exhaust when the air supply is disconnected.
3
www.nationalnail.com
WARNINGS
4
OPERATION OF THE TOOL
• Never inspect, maintain, repair, adjust, clear a jam or store the tool with the air connected.
• Never use the tool in proximity of flammable gases or liquids, as some tools will create sparks
that can be an ignition source for a fire or explosion.
• Always inspect the safety device for damage and proper operation, prior to operation.
• Never assume the tool is empty of fasteners.
• Never point the tool toward yourself or any other persons.
• Never cycle the tool unless it is in contact with the work-piece.
• Never use the tool as a hammer or wedging device or drop to the floor from any height.
• Always remove your finger from the trigger when pausing from cycling.
• Never tamper with the safety device or use the tool if the safety device is not functioning
properly.
• Use only 5/8” STINGER StaplePac cap fasteners with the STINGER™ CS58 Cap Stapler.
Never use any fasteners that are not specified for use in this tool. The CS58 holds 1 coil of
plastic caps (200 caps) and 2 strips of staples (100 staples each).
www.nationalnail.com
TOOL SPECIFICATIONS
Operating pressure 95-105 psi
Weight 3.9 lb.
Nail capacity 200 staples (2-100 count strips)
Cap capacity 200 plastic collated caps (1 reel)
Air inlet 3/8 NPT
Fasteners STINGER StaplePac (National Nail product number 0136360)
Consists of 20 strips of 5/8” 20 gauge staples (100 staples per strip)
and 10 reels of 1” diameter plastic collated caps (200 caps per reel).
5
www.nationalnail.com
LOADING THE TOOL
USE 5/8” STINGER STAPLEPAC CAP STAPLES ONLY
6
• Disconnect air.
• Open the magazine cover by pushing the green cover release
tab and lifting.
• Place cap reel in basket. Make sure the front end of the cap
coil is placed over the cap guide area of the basket. Insert
lead cap into the feed chute.
• Slide caps along the feed chute with fingers until they engage
the cap feeder. Pull the cap feeder back and release to
advance caps until the first cap is under the nose of the tool.
• Close the magazine cover.
• Depress the latch on the staple follower and pull back. Insert
two staple strips. Slide staple follower in and secure.
• Plug into air source. Tool is ready to use.
www.nationalnail.com
OPERATING THE TOOL
7
1. Do not use tool prior to reading the Owner’s Manual.
2. Read warning label(s) on the tool.
3. Visually inspect the tool for worn or damaged parts.
4. Wear appropriate eye and ear protection.
5. Install a male pneumatic fitting into the end cap of the tool, ensuring that the fitting allows the
tool to exhaust any air in the tool when the air hose is disconnected.
6. Add 2 drops of non-detergent, 20-weight oil into the male fitting.
7. Connect the air hose using a quick connect fitting to the tool, and check the air pressure
reading on the regulator to ensure it does not exceed 105 PSI. Check the tool for any air
leaks.
8. Place the tool, empty of fasteners, in operating position on a scrap work piece. Fully depress
the safety and pull the trigger to verify that the tool cycles.
9. Disconnect the air hose from the tool when:
• Loading staples and/or caps
• Performing inspection, maintenance or repair
• Clearing a staple or collated cap jam
• The tool is not in use
• Leaving the work area
• Moving the tool to another work location
• Handing the STINGER CS58 to another person
• Storing the tool
10. Following recommended loading instructions, load the fasteners approved for use in the tool.
Indice
