Nobu n12tbpc T201 Manuale utente
1
i
Preface
©
©Copyright 2004
All Rights Reserved.
The information in this document is subject to change without prior
notice in order to improve reliability, design and function and does not
represent a commitment on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special,
incidental, or consequential damages arising out of the use or inability
to use the product or documentation, even if advised of the possibility
of such damages.
This document contains proprietary information protected by copyright.
All rights are reserved. No part of this manual may be reproduced by
any mechanical, electronic, or other means in any form without prior
written permission of the manufacturer.
Safety Notices
1. Please read these safety instructions carefully.
2. All precautions and warnings on the equipment should be carefully
noted.
3. Please disconnect the computer from the AC outlet before cleaning.
4. Never pour any liquids into any openings or directly onto the
computer unit. This could result in fire or electrical shock.
ii
5. Ensure the voltage range of the power outlet is between 100V and
240V before connecting the computer unit. Exceeding the maximum
rated voltage may cause damage to the AC adapter or to the computer.
This could result in fire or electrical shock.
6. Do not leave this equipment in a non-temperature controlled
environment; storage temperatures below 4°C (39°F) or above 40°C
(104°F) may damage the unit.
To reduce the risk of an electric shock, which could cause
personal injury, please follow all safety notices. The symbols
shown are used in your documentation and on your
equipment to indicate safety hazards.
Lithium batteries can be dangerous. Danger of explosion if
battery is incorrectly replaced. Replace only with the same
or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s
instructions.
iii
Under no circumstances should the user attempt to
disassemble the power supply. The power supply has no
user-replaceable parts. Inside the power supply are
hazardous voltages that can cause serious personal injury. A
defective power supply must be returned to your dealer.
Safety Notices for the Power Cord
This equipment has a 2 or 3-wire power cord. Replace the power cord
if it becomes damaged. Contact your dealer for an exact replacement.
In the U.S.A. and Canada, the power cord must be a UL-listed
detachable power cord (in Canada, CSA-certified).
2-wire cord SPT-2 18AWG
3-wire cord SVT or SJT, 18 AWG, 3-conductor
Provide with a molded-on cord connector body at the other end. The
cord length must not exceed 3 meters.
Outside the U.S.A. and Canada, the plug must be rated for 250 VAC,
2.5 amp minimum, and must display an international agency approval
marking. The cord must be suitable for use in the end-user’s country.
Consult your dealer or the local electrical authorities if you are unsure
of the type of power cord to use in your country. Voltage changes occur
automatically in the power supply.
iv
Note-TNV Safety Caution
To reduce the risk of fire, use only No. 26 AWG or larger
telecommunication line cord. Avoid using a telephone (other
than a cordless type) during an electrical storm. There may
be a remote risk of electric shock from lightning. Do not use
the telephone to report a gas leak in the vicinity of the leak.
Notice of EMC Compliance
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and if not installed and used in
accordance with the instruction manual may cause harmful interference
to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
¾Reorient or relocate the receiving antenna.
¾Increase the separation between the equipment and receiver.
v
¾Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
¾Consult the dealer or an experienced technician for help.
Use only shielded I/O cables to connect I/O devices to this equipment.
You are cautioned the changes or modifications not expressly approved
by the party responsible for compliance could void your authority to
use the equipment.
Canadian EMI Compliance Statement
This Class B digital apparatus meets all requirements of the Canadian
Interference - Causing Equipment Regulations.
European Union CE Marking Declaration
This product has been tested and found to comply with the EMC
requirement subject to the EU directive for CE marking.
FCC Statement to Users for the FaxModem
This equipment complies with Part 68 of the FCC rules. On the bottom
of this equipment is the label that contains, among other information,
the FCC Registration Number and Ringer Equivalence Number for this
equipment. IF REQUESTED, THIS INFORMATION MUST BE
GIVEN TO THE TELEPHONE COMPANY.
The REN is useful to determine the number of devices you may connect
to your telephone line and still have all of those devices ring when your
telephone number is called. In most, but not all areas, the sum of the
REN’s of all devices connected to one line should not exceed five (5.0).
vi
To be certain of the number of devices you may connect to your line, as
determined by the REN, you should contact your local telephone
company to determine the maximum REN for your calling area.
If your telephone equipment causes harm to the telephone network, the
telephone company may disconnect your service temporarily. If
possible, they will notify you in advance. But if advance notice isn’t
practical, you will be informed of your right to file a complaint with the
FCC.
Your telephone company may make changes in its facilities, equipment,
operations or procedures that could affect the proper functioning of
your equipment. If they do, you will be notified in advance to give you
an opportunity to maintain uninterrupted telephone service.
The telephone company may ask you to disconnect this equipment from
the network until the problem has been corrected or until you are sure
that the equipment is not malfunctioning. This equipment may not be
used on coin service provided by the telephone company.
The Telephone Consumer Protection Act of 1991 makes it unlawful for
any person to use a computer or their electronic device to send any
message via a telephone facsimile machine unless such message clearly
contains in a margin at the top or bottom of each transmitted page or on
the first page of the transmission the following information:
¾The date and time of transmission
¾Identification of either business, business entity or individual sending
the message;
¾Telephone number of either the sending machine, business entity or
individual.
vii
In order to program this information into your fax/modem, please refer
to the appropriate instructions in your fax/modem manual.
viii
Laser Compliance Statement for CD-ROM, DVD-ROM, CD-
RW and DVD/CD-RW Combo Drives
The CD-ROM, DVD-ROM, CD-RW and DVD/CD-RW Combo drive
for this computer are laser products. The classification label of the
drive is located on the bottom of the drive. Below is a sample of the
classification label;
CLASS 1 LASER PRODUCT
LASER KLASSE 1
LOUKAN 1 LASERLAITE
APPAREIL A LASER DE CLASSE 1
KLASS 1 LASER APPARAT
The drive is certified in the USA to comply with the requirements of
the Department of Health and Human Services 21 Code of Federal
Regulations (DHHS 21 CFR) Subchapter J. for Class 1 laser products.
In other countries the drive is certified to comply with the requirements
of EN60825.
Indice
