Nokia MEDIAMASTER 9800 S Manuale utente

GB 1

Owner’s Manual

Mode d’emploi

Istruzioni per l’uso

Instrucciones de uso

MEDIAMASTER

9800 S

GB 2

Important Information

Wiring the plug (UK and Eire only)

The mains lead on this product is already fitted with a non-rewireable (moulded)

plug incorporating a fuse, the value of which is indicated on the pin face of the

plug. Should the fuse need to be replaced, an ASTA or BSI approved BS 1362 of

the same rating fuse must be used.

If the fuse cover is detachable, always refit the cover after replacing the fuse.

NEVER use the plug with the fuse cover omitted.

If the fitted plug is not suitable for your socket outlets, it should be cut off, after

having first removed the fuse, and an appropriate plug fitted in its place. If this

new plug contains a fuse, its value should be the same as that removed from

the non-rewireable plug.

The severed plug must be destroyed immediately to avoid possible shock

hazard.

If you need to replace the mains plug, follow the instructions given below:

The wires in the mains lead are coloured in accordance with the following code:

BLUE - Neutral (N): BROWN - Live (L).

As these colours may not correspond with the coloured markings identifying the

terminals in your plug, proceed as follows:

The wire coloured BLUE must be connected to the terminal marked with the

letter N or coloured BLUE or BLACK.

The wire coloured BROWN must be connected to the terminal marked with the

letter L or coloured BROWN or RED.

On no account should either of these wires be connected to the terminal

marked E or coloured GREEN or GREEN and YELLOW.

Before replacing the plug cover, make certain that the cord grip is clamped over

the sheath of the lead: not simply over the two wires.

If in doubt, consult a qualified electrician.

Nokia Multimedia Terminals operates a policy of continuous

development. Therefore we reserve the right to make changes

and improvements to any of the products described in this manual

without any prior notice.

The EMC Directive 89/336/EEC is applied to this product.

DiSEqC™ is a trademark of EUTELSAT

Nokia is a registered trademark of Nokia Corporation.

GB 3

MEDIAMASTER 9800 S

We reserve the right to change specifications.

Contents

GENERAL OPERATION OF THE

MEDIAMASTER 4

FOR YOUR SAFETY 4

REMOTE CONTROL 5

Rear Panel 6

Front Panel 6

ABOUT THE SMARTCARD AND CA MODULE7

Pay TV Services with a Smartcard (Viaccess) 7

Pay TV Services with a CA Module 7

INSTALLATION OF THE MEDIAMASTER 8

Preparing the Remote Control 8

Connecting the Mediamaster to the Dish 8

Connecting the Mediamaster to the TV 9

Connecting a TV and VCR 9

Connecting an Analogue Satellite Receiver

and VCR 10

Connecting a HiFi System 10

Switching on for the First Time with SCART

Connections 11

Tuning Procedure when RF Connections

are Used 11

FIRST TIME INSTALLATION 12

General Information 12

The Welcome Menu 12

Language 12

RF Modulator Type 13

Antenna/Satellite Selection 13

Common Menus 13

Antenna Adjustment and Signal Check 14

Line 1 Through 4 on the Antenna Satellite

Selection Menu 15

Line 5 and 6 on the Antenna Satellite

Selection Menu 15

Line on the Antenna Satellite Selection

Menu 16

One Antenna/One LNB Configuration 16

Multisatellite/DiSEqC Switch Configuration 17

Channel Search 18

Channel Search Progress 19

Time Adjustment 19

VIEWING MODE 20

General Information 20

Programme Information 20

The “i” (Information) Button 21

Guide 21

List of TV or Radio Channels 22

Options (Green Button) 22

TV Release (0) 23

Video Recording 23

The TEXT Button (Teletext) 23

EXIT TV 23

MAIN MENU 24

General Information 24

TV and Radio Channels 24

Edit Channels 24

System Configuration 29

Channel Search 29

Antenna/Satellite Configuration 29

TV Settings 30

Time Adjustment 30

Receiver Upgrade 31

Reinstall 31

User Preferences 31

Language Preferences 31

Parental Control 32

Appearance Preferences 32

System Information 33

Diagnostics 33

Conditional Access 34

Viaccess embedded 34

Common Interface (CI) 34

GLOSSARY OF TERMS 35

PROBLEM SOLVING 36

FRONT PANEL DISPLAY 37

TECHNICAL SPECIFICATIONS 38

MENU SCREEN STRUCTURE 39

GB 4

GENERAL OPERATION OF THE MEDIAMASTER

Throughout this manual you will notice that the everyday opera-

tion of your Mediamaster is based on a series of user friendly on-

screen displays and menus. These menus will help you get the

most from your Mediamaster, guiding you through installation,

channel selection, viewing and many other functions.

All functions can be carried out using the buttons on the remote

control, and some of the functions can also be carried out using

the buttons on the front panel.

If at any time when using the menus (except Installation and

Reinstall) you want to return to the normal TV/Radio mode, press

the EXIT button.

The Mediamaster is easy to use, always at your command and

adaptable for future advances.

Please be aware that new software may change the functional-

ity of the Mediamaster.

Should you experience any difficulties with the operation of your

Mediamaster, please consult the relevant section of this manual,

including the Problem Solving, or alternatively call your dealer or

a customer service adviser.

Please note: The first thing to do before sending the Media-

master to service is to:

1: Perform ”Diagnostic” procedure in System Information menu.

2: Try downloading new software into the Mediamaster.

With this procedure, the new software may solve the problem

in the quickest and most efficient way. See the relevant section

”Receiver Upgrade” further on in this manual.

•Allow clear space around the Media-

master for sufficient ventilation.

•Do not cover the Mediamaster or place

it on a unit that emits heat.

• Use a soft cloth and a mild solution of

washing-up liquid to clean the casing.

• Never allow liquids, spray or other materi-

als to come into contact with the inside of

the Mediamaster.

• Do not connect or modify cables when the

Mediamaster is plugged in.

FOR YOUR SAFETY

• Do not remove the cover.

• Do not allow the unit to be exposed to hot,

cold or humid conditions.

• Service should be carried out only at a Nokia

Authorised Service Centre.

• Please note that the only way to isolate the

Mediamaster completely from the mains

supply is to unplug the mains lead!

GB 5

To switch the Mediamaster in and out of standby mode.

EXIT TV To return to the viewing mode from a menu without stor-

ing settings (in menu mode).

To switch between TV or Radio (in viewing mode).

To turn the sound off/on (mute).

- + To adjust the volume of digital programmes.

The Mediamaster’s maximum level is controlled by the TV’s

present volume setting.

0 - 9 To change channel and to select individual menu options.

Note: If 0 is entered as the first digit, the TV Release func-

tionality is activated (see below).

0 TV Release. To switch between digital TV/Radio, analogue

TV and analogue satellite TV and VCR, when your systems

are connected by SCART leads.

Info. To display short and extended information (if transmit-

ted) about current and next programmes.

BACK To go back one level in the menus without storing settings.

TEXT To select teletext information.

Press to enter teletext (if available).

MENU To display or exit from the ”Main Menu” screen.

GUIDE To obtain a list of present and following programmes for the

available channels. This information is only shown if your

Service Provider transmits programme information (EPG in-

formation).

P+ P- To change channels up and down by one unit.

To change page in a menu/list/text if more than one page is

available. To browse through teletext history.

▼▲To move up/down in the menus and to change channels.

To change settings in menus.

OK To confirm choices and selection of a highlighted item.

To display the TV/Radio channel list.

(Red) At the moment, no function.

OPTION (Green) To select service options in viewing mode.

FREEZE (Yellow) To select the freeze function.

Press once to freeze the screen picture.

Press any other key to go to normal mode again.

(Blue) To toggle between present and previous TV/Radio

channels.

This section describes how to operate the Mediamaster using the buttons on the remote control.

Some of the functions can also be carried out using the buttons on the front panel.

REMOTE CONTROL

GUIDE

TEXT

BACK

EXIT

OPTION FREEZE

GB 6

Welcome

44 10285

85-265 V

50-60 Hz

WARNING!

DO NOT OPEN –

ELECTRICAL

SHOCK HAZARD

DIGITAL AUDIO

AUDIO

ANTENNA

13/18 V

500 mA

TV / VCR

TV AERIAL

SERIAL

AUX

AUDIO L R

phono connectors

Stereo outputs for

connection to a HiFi

system

TV SCART

for the

connection

to the TV

AUX SCART

for the connection to a

VCR, or an analogue

satellite receiver

*LNB cable also feeds the LNB with a

supply voltage of 13/18 V (V/H polarisa-

tion) and a 0/22 kHz signal (bandswitch).

Max LNB current 500 mA.

DIGITAL AUDIO

phono connector

S/PDIF output for

connection to

a HiFi system

Mains lead

95-260 V AC

50-60 Hz

ANTENNA *

Satellite dish

input (F-

connector)

Rear Panel

SERIAL PORT

to read and load

data information

Slot

for a CA module

with a Smartcard

to put the Mediamaster

in and out of standby

mode

to move up/down in

the menus and to

change channels.

Display

shows channel number, error

messages, remote control

commands and time in standby

mode

Front Panel

Slot

for a Smartcard

TV AERIAL

for a terrestrial

(conventional)

TV aerial

TV/VCR

for an RF-

cable to the

aerial input

of the TV or

VCR

Button

for a CA module

release

GB 7

To be able to receive scrambled digital satellite channels you will

need a Smartcard and/or a Common Interface CA (Conditional Ac-

cess) module from the Service Provider of your choice.

The Service Provider is the programme distributor.

If you are subscribing to services from more than one Service

Provider, you might have to change between different Smart-

cards and/or CA modules.

Please note that a Smartcard and CA module may only be valid

for a single Service Provider and due to this, a specific range of

channels.

The Smartcard and the CA module may also provide access to

special menus not described in this manual. If so, please follow

the instructions from the Service Provider.

Only ”free to air” channels are available without the Smartcard

and/or the CA Module.

Note: The Smartcard and/or the CA module are distributed by

your Service Provider.

After inserting the card, leave it in the slot permanently. Do not

remove it again, unless your Service Provider asks you to do so.

This is important, because if your Service Provider wants to

download new information to the Smartcard, the card has to be

in the slot.

Pay TV Services with a Smartcard (Viaccess)

Only for Pay-TV services coded with the Viaccess CA system.

• Insert your Smartcard fully into the slot behind the lid of the

front panel of the Mediamaster. The gold chip should face

downwards and inwards.

Pay TV Services with a CA Module

• Follow the instructions from your Service Provider concerning

the Smartcard and/or CA module.

• Insert the CA module (use only a DVB Standard, Common In-

terface CA Module) fully into the slot behind the lid of the front

panel of the Mediamaster.

• Press the grey button on the front panel if you need to remove

the CA module.

PIN Code

The Smartcard is loaded with a 4-digit code, also called a PIN code

(Personal Identification Number).

The code is essential in order to access future services offered

by the Service Provider.

ABOUT THE SMARTCARD AND CA MODULE

Note 1!

The gold chip

must be on the

underside of

the smartcard

Note 2!

Follow your Service

Providers instruc-

tions on how to in-

sert the CA module

GB 8

The box for your Mediamaster should contain the

following items:

• the Mediamaster

• a remote control with 2 AAA batteries

• a SCART lead (fully featured 1,0 metre)

• an aerial/RF lead (double screened 1,5 metres)

• an Owner’s Manual (this document)

• a Software License agreement

INSTALLATION OF THE MEDIAMASTER

About the SCART sockets

• The rear panel of the Mediamaster is equipped with 2 SCART

sockets (see diagram). When you connect other products

to any of these sockets, always use fully featured SCART

leads (as supplied). There are “less well specified” SCART

leads on the market and picture quality could be reduced if you

use them.

SCART socket

MEDIAMASTER 9850 T

SCART lead

Owner’s manual

License

agrement

RF lead

If you need to fit the F-connectors onto the cable

• Prepare each end of the cable as shown in the diagram. You

will need to fold back the outer braid (as shown).

• Slide the F-connector onto the cable, then turn it clockwise

until it grips the braid.

• Ensure that 3 mm of the core is protruding from the end of the

connector.

Preparing the Remote Control

• Remove the cover on the battery compartment at the bottom

of the remote control.

• Insert the 2 AAA (1,5 V) batteries, as shown in the diagram,

taking care to observe the +and -markings indicated inside.

• Replace the cover.

Installing the Satellite Dish

• See the ”Fitting instructions for satellite dish” on how to in-

stall the dish.

• Connect the coaxial cable, with F-connectors fitted, from the

LNB on the satellite dish to the socket marked ”ANTENNA”on

the rear panel of the Mediamaster (or e.g. a DiSEqC switch).

Connecting the Mediamaster to the Dish

8 mm

15 mm

3 mm

F-connector

GB 9

SCART connection

• Do not remove the TV aerial from the TV.

• Connect the SCART lead between the main SCART socket on

the TV and the TV SCART socket on the Mediamaster.

RF connection (dashed line)

• Connect an RF lead from the TV/VCR output on the Media-

master to the RF input socket on the TV.

• Connect the TV aerial to the TV AERIAL input socket on the

Mediamaster.

Connecting the Mediamaster to the TV

Connecting a TV and VCR

Refer to your VCR’s manual for full instructions.

• Connect one SCART lead between the main SCART socket on

the TV and the TV SCART socket on the Mediamaster.

• Connect another SCART lead between the VCR

and the AUX SCART socket on the

Mediamaster.

• Connect the RF lead from the RF output on the

VCR to the TV aerial input on the TV.

• Connect the TV aerial to the RF input socket on the VCR.

SCART

• Connect a SCART lead between the main SCART

socket on the TV and the TV SCART socket on the

Mediamaster.

• Connect an RF lead from the RF output on the

VCR to the TV aerial input on the TV.

• Connect an RF lead from the TV/VCR output on

the Mediamaster to the RF input socket on the

VCR.

• Connect the TV aerial to the TV AERIAL input

socket on the Mediamaster.

If your TV has a SCART socket, but your VCR does not

There are many different types of TV/VCR and other equipment

that you can connect to the Mediamaster.

In this manual you will see some of the most common ways to

connect your equipment.

If you use RF leads you will have to tune your TV and VCR to the

Mediamaster output channel (see page 11).

If you have problems with your connections and need help, con-

tact your dealer or Service Provider.

Connecting the Mediamaster

VCR

Mediamaster

SCART

GB 10

Connecting an Analogue Satellite Receiver and VCR

• Connect a SCART lead between the main SCART socket on

the TV and the TV SCART socket on the Mediamaster.

• Connect a SCART lead between the VCR and the AUX SCART

socket on the Mediamaster.

• Connect an RF lead from the RF output on the

VCR to the TV aerial input on the TV.

• Connect an RF lead from the RF output on the

Analogue receiver to the RF input socket on the

VCR.

• Connect the TV aerial to the RF input socket on the Analogue

receiver.

In order to switch the signal from the dish between the ana-

logue and digital receivers, you need a Nokia Smart priority

switch (at A B in the diagram) or a Universal Twin LNB.

Nokia Smart priority switch

• Connect a coaxial cable between output A on the NOKIA Smart

priority switch (accessory) to the LNB socket on the analogue

receiver.

• Connect a coaxial cable between output B on the NOKIA

Smart priority switch (accessory) to the ANTENNA socket

on the Mediamaster.

The analogue receiver must be switched to OFF (standby)

when you want to watch digital satellite channels from

the Mediamaster.

Universal Twin LNB

If you have a Universal Twin LNB you connect:

• Cable A between output A on the LNB to the

LNB socket on the analogue receiver.

• Cable B between output B on the LNB to the

ANTENNA socket on the the Mediamaster.

Both the VCR and the analogue satellite receiver must be

tuned to different UHF channels than the Mediamaster when

using RF-connectors.

Nokia Smart Priority Switch

NOKIA Smart

priority switch

Analogue receiver

Mediamaster

Connecting a HiFi System

• Connect an RCA/Cinch stereo cable from the AUDIO L R

sockets on the Mediamaster to the LINE, AUX, SPARE or

EXTRA input sockets on your HiFi system.

• If available you can connect an RCA/Cinch single cable from

the DIGITAL AUDIO socket on the Mediamaster to your HiFi

or Dolby Pro Logic system.

Note: To avoid interference you must use a screened video

cable.

Analogue receiver

Mediamaster

With Universal Twin LNB

With Nokia Smart

Priority Switch

VCR

SCART

VCR

SCART

Indice

Altri manuali Nokia Registratore digitale

Nokia

Nokia Mediamaster 9860 S Manuale utente

Manuali Registratore digitale popolari di altre marche

FLIR

FLIR M3100E Series Manuale utente

VTRACKPRO

VTRACKPRO FPRO300 Manuale utente

Swann

Swann NVR-7085 models Manuale utente

XtendLan

XtendLan DVR-1670C Manuale utente

urmet domus

urmet domus 1093/004AHD Manuale utente

Holux

Holux M1 Manuale utente

CMOS DOTCOM

CMOS DOTCOM ANX-1670 Manuale utente

Whistler

Whistler D16VRS Manuale utente

Defender Security

Defender Security 82-20235 Manuale utente

MISUMI

MISUMI MP-WF100M Manuale utente

Speco

Speco D8HU Manuale utente

UST

UST DDR-E04AA Istruzioni per l’uso

Consolidated

Consolidated Digital Video Recorder Manuale utente

Mace

Mace DVR0404RW Guida rapida

RCA

RCA RTD315W Manuale utente

FSM

FSM Colibri Grande PRO Manuale utente

Hauppauge

Hauppauge HD PVR 2 Manuale utente

Identivision

Identivision ICR-PH161i PIONEER Manuale utente