Nokia RH-10 Series Guida rapida
CCS Technical Documentation
RH-10 Series Transceivers
Issue 1 09/2002 Confidential Nokia Corporation
Disassembly / Assembly
RH-10
Disassembly / Assembly CCS Technical Documentation
Page 2 Nokia Corporation Confidential Issue 1 09/2002
CCS Technical Documentation Disassembly / Assembly
RH-10
Issue 1 09/2002 Nokia Corporation Confidential Page 3
Contents Page No
Disassembly................................................................................................................... 5
A-Cover..................................................................................................................... 5
Screws x 6 (4 x long top/bottom) (2 x short middle)................................................ 6
UI Snap Fit................................................................................................................ 6
Speaker...................................................................................................................... 7
Radio Module............................................................................................................ 7
System Connector ..................................................................................................... 8
RF Shield................................................................................................................... 8
Vibra Motor and Microphone ................................................................................... 9
Battery Connector (also see Battery Connector Handling, which follows)............ 10
Battery Connector Handling.................................................................................... 10
Antenna ................................................................................................................... 11
Volume Key ............................................................................................................ 11
RH-10
Disassembly / Assembly CCS Technical Documentation
Page 4 Nokia Corporation Confidential Issue 1 09/2002
CCS Technical Documentation Disassembly / Assembly
RH-10
Issue 1 09/2002 Nokia Corporation Confidential Page 5
Disassembly/Assembly Instructions
Order of photographs are for Disassembly.
To Assemble, simply reverse the order shown.
Note: Finger cots or gloves should be worn when phone is disassembled.
Note: ESD precautions should be strictly observed when handling unassembled phones.
A-Cover
(Disassemble) After removing the battery cover, grasp the bottom of the A-cover and the
bottom of the transceiver. Pull apart (photo below, left). The A-cover is hinged at the top;
do not force apart. The hinge releases when the bottom is fully separated from the trans-
ceiver.
(Assemble) Ensure that the keypad is properly seated in the A-cover, pressing at each of
the four guide pins with a fingertip (photo below, right). While holding the A-cover
approximately 30 degrees to the transceiver, engage the top hinge. Now push the bottom
of the A-cover towards the transceiver until it seats fully.
RH-10
Disassembly / Assembly CCS Technical Documentation
Page 6 Nokia Corporation Confidential Issue 1 09/2002
Screws x 6 (4 x long top/bottom) (2 x short middle)
(Disassemble) Using a size T6 driver, remove all six screws.
(Assemble) Replace the screws in the order shown in the photo below left. Be sure to
apply pressure to the board with the other hand to ensure a flat fit for all spring con-
tacts. The photo at right shows the different lengths of screws.
NOTE: Screw torque should be set at 16 Ncm +/-2 Ncm. This can only be achieved with a properly
calibrated torque driver. All torque drivers should have routine inspections for correct calibration and
proper performance.
UI Snap Fit
(Disassemble) Using a small, flat screwdriver or a pair of fine tweezers, gently disengage
one of the two snaps that hold the UI board to the B-cover (located on either side of the
phone, level with the bottom edge of the LCD). (Photo below, left, illustrates this.) The
second snap should disengage easily as the UI module is removed from the radio module
(photo below, right). Care should be taken to not damage the snaps.
(Assemble) Make sure the UI module is properly aligned with the radio module. Apply an
even, downward pressure to both snaps at once.
CCS Technical Documentation Disassembly / Assembly
RH-10
Issue 1 09/2002 Nokia Corporation Confidential Page 7
Speaker
(Disassemble) The speaker may now be removed, if needed, by carefully lifting at the
open cavities for the speaker snap fits. A pair of offset tweezers may be used to grasp
both sides of the speaker (see photo, below); then simply lift the speaker straight up.
NOTE: DO NOT pierce with sharp object, or touch the spring contacts of the speaker or display.
(Assemble) It is recommended that offset tweezers be used to insert the speaker, avoid-
ing contact with hands. It is important to keep the contacts safe.
NOTE: DO NOT touch the spring contacts.
Radio Module
(Disassemble) The radio module now is free to be removed.
NOTE: Be careful NOT to damage the springs of the battery contact or system connector while
removing the radio module.
(Assemble) Carefully install the radio module, using the guide pins on the B-cover for
position.
NOTE: Special care should be taken NOT to damage the spring contacts.
RH-10
Disassembly / Assembly CCS Technical Documentation
Page 8 Nokia Corporation Confidential Issue 1 09/2002
System Connector
(Disassemble) Once the radio module has been removed, the system connector is free to
be removed from the B-cover.
NOTE: Take care NOT to touch the springs during assembly or disassembly. Also, do not lay aside
with contacts down.
(Assemble) See the NOTE above for precautions
RF Shield
(Disassemble) The RF shield is free to be removed by grasping at top and bottom (see
photo below), carefully lifting over the battery contact springs. Do not use the center of
shield for removal, as damage to shield springs or battery contact springs may occur.
(Assemble) Great care should be taken to avoid contact with the battery contact springs
and to avoid damage.
CCS Technical Documentation Disassembly / Assembly
RH-10
Issue 1 09/2002 Nokia Corporation Confidential Page 9
Vibra Motor and Microphone
(Disassemble) Note two through-holes located in the bottom of the connector (photo,
below left). A small, blunt object may be inserted to help dislodge the microphone or
vibra motor. The motor may also be removed by gently lifting the vibra shaft. Do not
force the motor out; damage will occur. If the assemblies are to be reused, be careful not
to touch any spring contacts.
(Assemble) Use tweezers to reinsert (photo, below right), using the tip to fully seat.
NOTE: DO NOT use fingertips to seat! Overstress by pushing on spring contacts can lead to intermit-
tent failures in time, even if the initial testing is okay.
RH-10
Disassembly / Assembly CCS Technical Documentation
Page 10 Nokia Corporation Confidential Issue 1 09/2002
Battery Connector (also see Battery Connector Handling,which follows)
(Disassemble) Insert the tip of a very thin, flat-tip screwdriver (or similar instrument)
between the battery connector and the B-cover wall (at approximately the center of the
battery connector). Gently rock the handle of the screwdriver (see photo below) down-
ward to disengage the two locking clips and to lift the battery connector upward.
(Assemble) Carefully place the connector in the B-cover. Then use a small screwdriver or
tweezer tip to push the center of the connector in order to fully seat. You should hear/
feel the locking mechanism engage.
Battery Connector Handling
The springs that make contact with the PWB can be easily bent while exposed or while
outside of an assembled phone. Take care NOT to touch these contacts at any time if the
connector is to be reused. Tweezers should be used to remove new connectors from tray.
Altri manuali per RH-10 Series
1
Indice
Altri manuali Nokia Ricetrasmettitore
Nokia
Nokia RH-27 Series Istruzioni operative
Nokia
Nokia RH-27 Series Guida
Nokia
Nokia NPC-1 Series Guida
Nokia
Nokia NSB-9 Manuale utente
Nokia
Nokia RH-27 Series Guida
Nokia
Nokia NPM-6 Series Manuale utente
Nokia
Nokia NSM-3 Manuale utente
Nokia
Nokia RM-696 Manuale utente
Nokia
Nokia NHM-4 Series Istruzioni per l'installazione
Nokia
Nokia NPM-6 Series Manuale utente
Nokia
Nokia NSE-6 SERIES Guida
Nokia
Nokia RH-57 Series Istruzioni operative
Nokia
Nokia NHM-1 Series Guida
Nokia
Nokia RM-11 Series Istruzioni operative
Nokia
Nokia NHM-4 Series Manuale utente
Nokia
Nokia RH-21 Series Guida
Nokia
Nokia NKC-1X Series Guida
Nokia
Nokia NPM-6 Series Manuale utente
Nokia
Nokia RH-34 Series Guida
Nokia
Nokia NKC-1X Series Istruzioni per l'installazione
