Nokia RH-41 Series Istruzioni per l'installazione

CCS Technical Documentation

RH-41 Series Transceivers

Issue 2 09/2003 Confidential Nokia Corporation

Disassembly

RH-41

Disassembly CCS Technical Documentation

Page 2 Nokia Corporation Confidential Issue 2 09/2003

CCS Technical Documentation Disassembly

RH-41

Issue 2 09/2003 Nokia Corporation Confidential Page 3

Disassembling the RH-41 Basic Transceiver

Remove the back cover.

Step 1. Push down hard on the button.

Step 2. Slide the cover in the direction of the

Remove the battery.

arrow.

Step 1. Place fingers on both ends of the battery latch.

Step 2. Push the latch away from the battery.

The battery will bounce off.

Remove the front cover.

Step 1. Get a firm hold on the phone around the

accessory interfaces (in the D-cover).

Step 2. Hold the side of the front cover as indicated by

the arrow in the D-cover.

Step 3. Life the side up.

Note: The picture shows the assembly order.

Assembly is in the reverse order.

Remove six screws.

Remove the PWB from the housing.

RH-41

Disassembly CCS Technical Documentation

Page 4 Nokia Corporation Confidential Issue 2 09/2003

Note: The use of gloves is mandatory while removing

the system connector, in order to prevent

fingerprints from appearing on the engine and

the springs. The springs may be damaged,

if touched.

Note: The screwdriver must not hit the engine module’s

components during disassembly.

6. The system connector assembly should

stay on the engine when the D-cover

is moved. It can be removed manually.

7. Step 4. Remove the engine module.

Note: The use of gloves is mandatory while removing

the engine module, in order to prevent

fingerprints from appearing on the engine.

Note: If the LCD module is to be reused, the use of

gloves is mandatory to prevent fingerprints from

appearing on the domes and elastomer connector.

The domes and the elastomer connector may be

damaged, if touched.

Step 5. Lift it off the C-cover.

Disassemble C- and D-covers.

Step 1. Place a screwdriver with a chisel point

between the C- and D-covers’ snap feature.

Step 3. Remove the system connector.

Please use tweezers or a small screwdriver to remove the shield lid. Snap it open carefully.

be removed extremely carefully, so as not to damage any other parts of the radio module.

When removing the shield lid, please pay special attention to how it is done. The lid needs to

absolutely straight so that spurious radiation does not occur.

If the RF shield lid is removed, replace it with a new one as it is vital that the shield is

Note:

The engine module can be removed manually.

Remove the LCD module.

Step 2. Lift the D-cover.

CCS Technical Documentation Disassembly

RH-41

Issue 2 09/2003 Nokia Corporation Confidential Page 5

Note: Handle with care, as the speaker and the

springs may be damaged, if touched.

10.

11.

12.

You can remove the IR window once the

antenna has been removed.

Step 9. Remove the IR window.

13.

Note:Do not reuse the battery connector after disassembly.

Remove the battery connector.

Step 10. Push the battery connector from the

battery side to remove it.

prevent the reuse of the antenna.

during disassembly. The broken snap will not

Note: The antenna’s snap feature may be damaged

Step 8. Lift the antenna.

D-cover.

between the antenna and the

Step 7. Place a flathead screwdriver

Remove the antenna.

from the antenna.

Step 6. Bend the latch and push it away

Step 5. Get a firm hold on the middle of the latch.

Remove the battery latch.

Step 4. Remove the speaker

assembly from the

C-cover.

RH-41

Disassembly CCS Technical Documentation

Page 6 Nokia Corporation Confidential Issue 2 09/2003

14. Remove the release spring.

Step 11. Use a flathead screwdriver to remove

the release spring from the D-cover.

The heat-staking features will break during

disassembly.

Note: The broken heat-staking features will not prevent replacing a new release spring

15.

Remove the vibra assembly.

Step 12. Lift the vibra assembly from its slot.

Use a screwdriver or your finger.

16.

Remove the buzzer assembly.

Step 13. Place a screwdriver with a chisel-point

between the buzzer assembly and the

D-cover.

Step 14. Lift the buzzer assembly.

The heat-staking features will break during

disassembly.

Note: The broken heat-staking features will not prevent the use of the buzzer.

17.

Remove the metal deck.

Step 15. Release the four side locks with a

screwdriver.

Step 16. Push the metal deck from the engine’s side.

Note: Do not reuse the metal deck after disassembly.

or buzzer onto the cover.

CCS Technical Documentation Disassembly

RH-41

Issue 2 09/2003 Nokia Corporation Confidential Page 7

The main parts of the phone disassembled.

RH-41

Disassembly CCS Technical Documentation

Page 8 Nokia Corporation Confidential Issue 2 09/2003

Altri manuali per RH-41 Series

Indice

Altri manuali Nokia Ricetrasmettitore

Manuali Ricetrasmettitore popolari di altre marche

Yaesu

Yaesu FT-7B Manuale utente

Kenwood

Kenwood ProTalk TK-3201 Manuale utente

Texas Instruments

Texas Instruments TLK10232 Manuale utente

Mizuho

Mizuho MX-2 Guida del prodotto

Kenwood

Kenwood TK-3180 Manuale operativo e di manutenzione

Blitz

Blitz MJ-398U Manuale utente

Utilicom

Utilicom LongRanger 2050 Manuale utente

Standart

Standart HX290UKA Manuale utente

Altronix

Altronix Pace1PTM Manuale utente

Kirisun

Kirisun PT2208 Manuale utente

ELECRAFT

ELECRAFT KX2 Manuale utente

Zodiac

Zodiac K3 Manuale utente

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manuale utente

Kenwood

Kenwood TK-2217 Manuale utente

Siemens

Siemens PSO 4000 Manuale utente

Kenwood

Kenwood TS-590SG Manuale utente

Midland

Midland G8E-BT Manuale

ComNav

ComNav Mariner X2 Manuale utente