Nortech SP1 Manuale utente
READER WIRING INSTRUCTIONS
DOC0067 Issue 1.0
125kHz reader models with
the following prefixes:
13.56MHz reader models
with the following prefixes:
MP1-EM1
MP1-HT1
MP1-DP1
WP1-EM1
WP1-HT1
WP1-DP1
SP1-EM1
SP1-DP1
SP1-DP1
WP2-EM1
MP1-LEG
MP1-MIF
MP1-ISO
WP1-LEG
WP1-MIF
WP1-ISO
SP1 MP1 WP2 WP1
125KHz Reader Wiring
Connect the reader cable to the reader port of the controller according to
the table below. For readers with a screw terminal block, refer to terminal
numbering diagram.
Terminal* Cable Function
1 Red +5VDC to +16VDC
2 Black Ground
3 Yellow Green LED input
4 White Wiegand Data 1 / Clock
5 Green Wiegand Data 0 / Data
8 Brown Beeper input
9 Orange Format Select (see below)
10 Blue Serial Data Output
Format Select: Use the ‘Format Select’ lead to set the required data output
format by connecting it to either Ground or +VDC as follows:
Reader Variant Connect to Ground Connect to +VDC
EM1, HT1 10-Digit Clock & Data 26-Bit Wiegand
DP1 26-Bit Wiegand 44-Bit Wiegand
1 2 3 4 5
9
8
7
6
13
12
11
10
*Terminal
Numbering
13.56MHz Reader Wiring
Connect the reader cable to the reader port of the controller according to
the table below. For readers with a screw terminal block, refer to terminal
numbering diagram.
Terminal* Cable Function
1 Red +5VDC to +16VDC
2 Black Ground
3 White Wiegand Data 1 / Clock
4 Green Wiegand Data 0 / Data
5 Yellow Green LED input
6 Brown Beeper input
7 Blue Serial Data Output
8 Orange Format Select (see below)
Format Select: Use the ‘Format Select’ lead to set the required data output
format by connecting it to either Ground or +VDC as follows:
Reader Variant Connect to Ground Connect to +VDC
ISO 10-Digit Clock & Data 32-Bit Wiegand
MIF, LEG Dependant upon the customer specific version
*Terminal Numbering
1 2 3 4 5 6 7 8
Power & Testing
Once the reader is fitted and wired, carry out a brief test to ensure that it
is functioning correctly. You may need to refer to the controller reference
documentation.
Connect power to the controller and ensure that the LED lights red.1.
The reader requires a supply of 5VDC to 16VDC.
Present a compatible card to the reader and check that the LED blinks2.
green and the beeper sounds (if fitted).
Make a card valid in the access controller and present the card to3.
the reader. Ensure that the card is accepted and the LED and beeper
respond to the access controller as expected. This will depend upon
how you have wired the reader and the way in which the access
controller operates.
If the card details are not recognised by the access controller, check all
connections and ensure that you have connected the ‘Format Select’
input correctly according to the table in the wiring instructions..
Note 1: The Slimline reader uses two separate LEDs for red and green
indications but the basic operation is the same as other models.
Note 2: If the LED does not give any indication at all when a card is
presented, it is likely that the reader technology does not match
that of the card.
Specifications
MP1 WP1 WP2 SP1
Supply Voltage 5VDC to 16VDC
Max. Current 250mA 70mA
Read Range Up to 100mm Up to 50mm Up to 80mm
Indications Dual colour LED (red/
green), Beeper
Dual colour
LED (red/
green)
Red LED’
Green LED,
Beeper
IP Rating IP65
Operating
Temperature -20oC to 50oC
For further details, view or download the corresponding product datasheet
from the Nortech website at:
http://www.nortechcontrol.com/document-library.aspx
Product mounting templates
are also available at this
location.
READER FITTING INSTRUCTIONS
Fitting Mullion and Wall Switch Readers
For those readers fitted with a cover (MP1 and WP1) ensure that the cover
securing screw is not fitted to the base of the reader, and separate the front
cover and the reader body as follows:
Insert the tip of a terminal screwdriver into
the small slot in the base of the cover. Press
lightly to release the securing catch while
you separate the cover from the reader at
the base.
Mounting the Mullion Reader
Identify a suitable location for the
reader at a convenient height near to
the door that it controls.
Place the reader on the mounting
surface and mark the position of the
cable hole. Drill a hole suitable for
feeding the cable through.
If the reader is fitted with a cable,
feed it through the hole so that the
reader can be positioned correctly
against the mounting surface. Ensure
that the reader is level and mark out
the position of the fixing holes, drill
and prepare the holes. Terminate the
cable conductors according to the
wiring details overleaf.
If the reader is fitted with screw terminals, position the reader against the
mounting surface, ensure that the reader is level and mark out the position
of the fixing holes. Drill and prepare the fixing holes. Feed the connecting
cable through the cable hole and terminate the conductors according to the
wiring details overleaf.
Secure the reader to the mounting surface using the two no.6 wood screws
supplied with appropriate plugs/fixings (not supplied) for the type of
mounting surface.
Mounting the Wall Switch Reader
Wall Switch readers are designed to fit to a standard wall switch back box
(minimum depth 25mm). The WP1 can also be mounted directly on a wall
(see the instructions for fitting a mullion mount reader).
If the reader is to be mounted on a back box and is fitted with a cable, feed
the cable through the hole in the back box to the controller and terminate the
conductors according to the wiring details overleaf. If the reader is fitted with
screw terminals, feed the connecting cable into the back box and terminate
the conductors according to the wiring details overleaf.
Secure the reader to the back box using the screws supplied.
Note:
To fit the Flush-mount Wall Switch
reader to a back box, follow the
mounting instructions above.
Fitting The Reader Cover (MP1 and WP1)
Once the reader has been fitted and wired, the cover can be fitted as
described below (the illustration shows the mullion model but the procedure
is the same for the wall switch model).
Hook the two tabs at the top of the reader cover over the top of the1.
reader back plate, engaging them with the corresponding slots in the
back plate.
Hinge the cover over the reader body until it is correctly seated over2.
the reader (it should click into place).
Insert the cover retaining screw in the base of the reader and tighten.3.
1
2
3
Fitting the Slimline Reader
Identify a suitable location for the reader at a convenient height near1.
to the door that it controls.
Mark out the position of the unit and then drill holes for mounting2.
screws and the cable.
Feed the cable through the wall and terminate it either at the access3.
controller or in a suitable terminal box.
Screw the reader to the wall using the screws provided and4.
appropriate plugs/fixings (not supplied) for the type of mounting
surface)
Terminate the conductors according to the wiring details overleaf.5.
Fit the label once the reader has been fully installed and you are6.
confident that the unit will not need to be moved.
80 mm
Questo manuale è adatto per i seguenti modelli
18
Indice
Altri manuali Nortech Lettore di schede
