Norton Clipper TR 232 S Manuale utente

TR 232 S&L

OPERATING INSTRUCTIONS

Translation of the original instructions

VERS. 2016.04.29 TR 232_MAN_EN

The undersigned manufacturer:

SAINT - GOBAIN ABRASIVES S.A.

190, BD J.F. KENNEDY

L- 4930 BASCHARAGE

Declares that this product:

Tile Saw (code): TR 232 S 230 V (70184601110)

TR 232 S 230 V UK (70184601111)

TR 232 S 115 V (70184601109)

TR 232 L 230 V (70184601103)

TR 232 L 230 V UK (70184601105)

TR 232 L 115 V (70184601104)

Is in conformity with the following Directives:

"MACHINES" 2006/42/CE

"LOW VOLTAGE" 2014/35/UE

"ÉLECTROMAGNÉTIC COMPATIBILITY" 2014/30/UE

"NOISE" 2000/14/CE

and European standard:

EN 12418 –Masonry and stone cutting-off machines –Safety

Valid for machines as of serial number:

1601xxxxxxx

Storage site for the technical documents :

Saint-Gobain Abrasives 190, Bd. J. F. Kennedy 4930 BASCHARAGE, LUXEMBOURG

This declaration of conformity loses its validity when the product is converted or modified

without agreement.

Bascharage, Luxembourg, 04.01.2016

Olivier Plenert, executive officer.

Declaration of conformity

VERS. 2016.04.29 TR 232_MAN_EN

TR 232 S&L

OPERATING INSTRUCTIONS

1BASIC SAFETY INSTRUCTIONS 6

1.1 Symbols 6

1.2 Machine plate 7

1.3 Safety instructions for particular operating phases 7

2MACHINE DESCRIPTION 9

2.1 Short description 9

2.2 Purpose of use 9

2.3 Layout 9

2.4 Technical Data 11

2.5 Statement regarding the vibration emission 12

2.6 Statement regarding noise emission 13

3ASSEMBLY AND COMMISSIONING 14

3.1 Assembly of the legs 14

3.2 Assembly of the handles 14

3.3 Cutting head 15

3.4 Assembly of the cooling system 15

3.5 Transport wheels 16

3.6 Longitudinal guide assembly 16

3.7 Side extension assembly 17

3.8 Installation of the handle for the cut in angle 17

3.9 Installation of the material holding system (TR 232 L only) 19

3.10 Tool assembly 18

3.11 Electrical connections 19

3.12 Water cooling system 19

3.13 Starting the machine 19

4TRANSPORT AND STORING 20

4.1 Securing for transport 20

4.2 Storing of the machine 20

5OPERATING THE MACHINE 22

5.1 Site of work 22

5.2 Cutting 22

Important for cutting 22

5.3 Cutting with an angle 23

6MAINTENANCE AND SERVICING 24

7FAULTS: CAUSES AND CURES 25

7.1 Fault-finding procedures 25

7.2 Trouble-shooting guide 25

7.3 Circuit diagram 26

7.4 Customer service 27

VERS. 2016.04.29 TR 232_MAN_EN

1 BASIC SAFETY INSTRUCTIONS

The TR 232 is exclusively designed for the cutting of tiles with NORTON diamond disks mainly on

construction sites.

Uses other than the manufacturer's instructions shall be considered as contravening the regulations.

The manufacturer shall not be held responsible for any resulting damage. Any risk shall be borne

entirely by the user. Observing the operating instructions and compliance with inspection and

servicing requirements shall also be considered as included under use in accordance with the

regulations.

1.1 Symbols

Important warnings and pieces of advice are indicated on the machine using symbols. The following

symbols are used on the machine:

Read operator's instructions

Ear protection must be worn

Hand protection must be worn

Eye protection shall be worn

Rotation direction of the blade

Danger: risk of cut

VERS. 2016.04.29 TR 232_MAN_EN

1.2 Machine plate

Important data can be found on the following plate located on the machine:

1.3 Safety instructions for particular operating phases

Before commencing work

Before commencing work, make yourself familiar with the working environment at the place of

use. The working environment includes: obstacles in the area of work and manoeuvre, the

firmness of the floor, necessary protection at the site relating to public thoroughfares and the

availability of help in the event of accidents.

Site the machine on an even, firm and stable base!

Check for correct mounting of the blade regularly.

Immediately remove damaged or badly worn blades, as they endanger the operator whilst

rotating.

The material to be cut must be held securely in place on the table to allow no unexpected

movement during cutting operation.

Always cut with the blade guard in position.

Only fit NORTON diamond blades with continuous rim to the machine! The use of other tools

can damage the machine!

Read the blades’ specifications carefully to choose the correct tool for your application.

Attention is drawn to the use of BS2092 safety goggles in conformity with specified Processes

No.8 of the Protection of Eyes Regulation 1974, Regulation 2(2) Part 1. Also use the other

safety equipment as mentioned in the symbols plus a dust mask when dry cutting is applied.

Machine Model

Machine Code

Weight

Year of production

Maximum blade diameter

Machine type

Serial number

Power

Safety standard

Blade speed

Bore

diameter

VERS. 2016.04.29 TR 232_MAN_EN

Electrical powered machine

Always turn off the TR 232 and separate it from the main source of electricity before any work on

the machine is done.

Make all electrical connections securely to eliminate contact of live wires with spray water or

dampness

When TR 232 is used with water, it is IMPERATIVE that you earth the machine properly. Let a

qualified electrician check in case of doubt.

Press the red button (0) on the switch to stop the machine in case of emergency.

In the event of the TR 232 breaking down or stopping for no apparent reason, switch off the

main electricity supply. Only a qualified electrician is allowed to investigate the trouble and

remedy the fault.

VERS. 2016.04.29 TR 232_MAN_EN

2 MACHINE DESCRIPTION

Any modification, which could lead to a change in the original characteristics of the machine, may

be done only by Saint-Gobain Abrasives who shall confirm that the machine is still in conformity with

the safety regulations.

2.1 Short description

The TR 232 Saw is designed for durability and high performance for onsite wet cutting operations of

a wide range of tiles.

As with all other NORTON CLIPPER products, the operator will immediately appreciate the attention

given to detail and quality of materials used in construction. The machine and its component parts

are assembled to high standards assuring long life and minimum maintenance.

2.2 Purpose of use

The machine is designed for wet cutting of a large range of building and refractory materials, or tiles.

It is not designed for cutting wood, metals or other materials.

2.3 Layout

Frame (1)

VERS. 2016.04.29 TR 232_MAN_EN

The frame is made of aluminium and steel to ensure robustness and durability. The folding stand

with 4 legs ensures stability while cutting.

Cutting head (2)

Aluminium console guided with precision. This console supports the electric motor, the guides and

the blade guard. The head can be tilted to cut with an angle from 0 to 45º.

Blade guard (3)

The blade guard assembly with a 230mm-diameter blade capacity is completely closed, but the

outside cover can be disassembled to access the blade. It offers maximum operator protection and

increased visibility of the work piece. The tightening of the fixing flange is done by a hexagonal head

screw (left-hand thread).

Water cooling (4)

The coolant system comprises:

A submersible mechanical water pump.

Plastic suction pipe delivering the water from the water pan to the cutting head.

A removable large capacity plastic water pan located under the cutting table to reduce water

loss.

A nozzle of watering located on the casing of the disc for a good distribution of water on the

disc.

Electric Motor (5)

One phase 1,1 kW motor. The switch with the red and green buttons is used to start and turn off the

engine. The red button is also an emergency stop.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Norton Sega

Norton

Norton BBL547 Manuale utente

Norton

Norton Clipper ISM Manuale utente

Norton

Norton BBL547 Manuale utente

Norton

Norton clipper CS1-500 P13 Manuale utente

Norton

Norton clipper CM 350 B Manuale utente

Norton

Norton Clipper C1318P Manuale utente

Norton

Norton clipper CS 352 Manuale utente

Norton

Norton C1316 Manuale utente

Norton

Norton TT 200 EM Manuale utente

Norton

Norton Clipper CS1 P13 Manuale utente

Norton

Norton clipper CS 352 B Manuale utente

Norton

Norton Clipper C13PE Manuale utente

Norton

Norton CGW 1.30.1 230V Manuale utente

Norton

Norton Clipper CTC1020XL Manuale utente

Norton

Norton Clipper TR 202 Manuale utente

Norton

Norton Clipper CMV 1000 Verto Manuale utente

Norton

Norton CS 451 P13 Guida

Norton

Norton clipper TR 231 GL Manuale utente

Norton

Norton JCW 600 Manuale utente

Norton

Norton Clipper C1418P Manuale utente

Norton

Norton clipper CS 502LV P13 Manuale utente

Norton

Norton clipper CM 450 Junior Manuale utente

Norton

Norton CST 65 Modulo Manuale utente

Norton

Norton TC-405 Manuale utente

Manuali Sega popolari di altre marche

RIDGID

RIDGID BS1400 Manuale utente

ATIKA

ATIKA BWS 400-2 Manuale utente

RGC

RGC FS20 Manuale utente

Makita

Makita M2300 Manuale utente

IMET Spa

IMET Spa BASIC 300 PLUS SHI Manuale utente

IMET Spa

IMET Spa SIRIO 370 AF-E Manuale utente

Optimum

Optimum OPTisaw CS 275 Manuale utente

Makita

Makita BPB180 Manuale utente

Stihl

Stihl MS 462 C-M Manuale utente

AEG

AEG TS 250 K Manuale utente

Meec tools

Meec tools 004665 Manuale utente

Makita

Makita LS1018L Manuale utente

Ryobi

Ryobi RCS1400 Manuale utente

DeWalt

DeWalt DCS391 Manuale utente

Sealey

Sealey SA72 Manuale utente

skilsaw

skilsaw SPT88 Istruzioni per il montaggio

Urrea

Urrea SI810 Dimensioni e guida di installazione

EINHELL

EINHELL BKG 210/1 Manuale utente