Novar EP/2-EA Manuale utente

Ethernet®Adapter

Installation Instructions

DOC. #569040000—A 7/30/04 PRINTED IN U.S.A.

Disclaimer

Logic One®is a registered trademark of Novar Controls Corporation.

The material in this manual is for information purposes only. The contents and the product it

describes are subject to change without notice. Novar Controls Corporation makes no

representations or warranties with respect to this manual.

In no event shall Novar Controls Corporation be liable for technical or editorial omissions or mistakes

in this manual, nor shall it be liable for any damages, direct or incidental, arising out of or related to

the use of this manual.

No part of this manual may be reproduced in any form or by any means

without prior written permission from Novar Controls Corporation.

Novar Controls Corporation

6060 Rockside Woods Blvd., Cleveland, OH 44131

Tel: 800.348.1235 www.novarcontrols.com

Description

The Ethernet®Adapter module (Model EP/2-EA) is connected to Novar

Controls’ Executive Processor 2 (EP/2) to allow the EP/2 to communicate over a

Local Area Network (LAN) that uses Ethernet hardware and software. The

Ethernet network provides the capability for multiple EP/2s, Novar Controls

workstations, and other devices to communicate with each other across the

network. By communicating with an EP/2 through Ethernet, any properly

configured personal computer can access real-time, online data from the Logic

One®system.

The EP/2 requires a PROM level of 18.20 or greater and a download version of

18.20 or greater to use the Ethernet Adapter.

Specifications

Operating Environment

Temperature: 32° to 140°F (0° to 60°C)

Humidity: 0 to 95% Relative, noncondensing

Physical Dimensions

Height: 7 inches

Width: 3.63 inches

Depth: 1 inch

Weight: 8 oz (All aluminum enclosure)

Precautions

Observe all national and local electrical codes during installation.

Mounting the Ethernet

Adapter

CAUTION! Remove the EP/2 electronics assembly before

mounting the Ethernet Adapter to the EP/2 baseplate.

The following items are needed for installation:

§Ethernet Adapter

§Three 1-inch screws (included with the adapter’s hardware kit)

§A twisted-pair, Ethernet-compatible cable (10Base-T) with an RJ-45 connector.

The adapter should be mounted inside the EP/2 baseplate enclosure, to the left of

the EP/2’s transition board (see Figure 1).

NOTE! Complete the installation procedures in the order they are

presented in these instructions. Varying from these

instructions could result in damage to the Ethernet Adapter

and/or the EP/2.

Doc. #569040000—A 7/30/04 1

Ethernet®Adapter Installation Instructions

NOTE! The knockout hole on the left side of the EP/2 baseplate

will be blocked by the Ethernet Adapter. If wires run

through this hole, they must be rerouted. Do not route

them under the adapter. The Ethernet Adapter must sit

firmly against the baseplate to ensure a proper connection.

Use the following procedure to mount the Ethernet Adapter to the baseplate of

the EP/2.

Step Procedure

1 Use the hex wrench that came with the hardware kit to loosen

the two screws at the bottom of the EP/2 baseplate and lift off the

cover.

2 Loosen the retaining screws in the two mounting posts on which

the EP/2 electronics assembly sits.

§Completely remove the screw from the left mounting post (as

indicated in Figure 1).

NOTE! The Ethernet Adapter and the EP/2 electronics

assembly will not connect properly unless the left

mounting post screw is removed and the adapter is

installed before the electronics assembly is

returned to the EP/2 baseplate.

3 Slide the EP/2 electronics assembly up and away from the lip at

the top of the baseplate and set it aside.

continued

2Doc. #569040000—A 7/30/04

Ethernet®Adapter Installation Instructions

EXECUTIVE PROCESSOR 2

24V,1A

RS-232 PORT

CLASS2, 5V MAX CIRCUITS

RS-485COMMUNICATION NETWORKS

LAN

'B'M ODULE

DIRECTION DIRECTION

'A'MODULE

SHIELD SHIELD SHIELD

INPUT

SENSOR

INPUT

SENSOR

OUTDOORLIGHT

OUTDOORTEMP

PULSE

DEMAND

LOSS

PHASE

POWERINPUT

STATUS

30VA

CLASS2

INPUTINPUTINPUT

TELEPHONELINE

TRANSITION BOARD

NOVARCONTROLS CORPORATION

EMERGENCY

OUTPUTX

24VAC

WARNING

DONOT PLUG THISMODULE INTO A

POWEREDCONTROLLER!

10BASE-TLAN

CONNECTION

MOUNTCONTROLLER BASEPLATEAND SLIDE

CONTROLLERELECTRONICSINTO PLACE.

RECEIVE

TRANSMIT

POLARITY

COLLISION

GOODLINK

ETHERNET Adapter

MODEL EP/2 - EA

Remove this screw before

mounting the Ethernet Adapter

EP/2 Baseplate with

Electronics removed

Position the Ethernet

Adapter over these

mounting posts and

align the holes so the

screws can be inserted

Ethernet address

(M.A.C. identification)

Insert the Ethernet network

cable here

Figure 1. Ethernet Adapter Module Installation

Step Procedure

4 Align the adapter’s three mounting holes with the three mounting

posts (shown in Figure 1) and carefully push the adapter toward

the baseplate.

5 Insert the three 1-inch screws included with the mounting kit (see

Figure 2), making certain that they are aligned correctly, and

tighten (using a Phillips screwdriver) to ensure the adapter is

mounted securely.

Making Connections to

the Ethernet Adapter

Use the following procedure to connect the Ethernet Adapter to the EP/2.

Step Procedure

1 Insert the RJ-45 connector from the Ethernet network cable into

the port on the right side of the Ethernet Adapter (see Figure 1).

2 Slide the EP/2 electronics assembly over the lip at the top of the

baseplate and down over the mounting posts.

3 Locate the DB-37 connector on the top of the adapter, carefully

align the pins, and guide the DB-37 connectors on the EP/2

electronics assembly over the connector on the Ethernet Adapter

and over the connector on the transition board of the EP/2.

§Do not force the connection.

continued

Doc. #569040000—A 7/30/04 3

Ethernet®Adapter Installation Instructions

WARNING

DO NOT PLUG THIS MODULE INTO A

POWERED CONTROLLER!

10BASE-T LAN

CONNECTION

MOUNT CONTROLLER BASEPLATE AND SLIDE

CONTROLLER ELECTRONICS INTO PLACE.

RECEIVE

TRANSMIT

POLARITY

COLLISION

GOOD LINK

ETHERNET Adapter

MODEL EP/2 - EA

Insert three screws here

to mount the Ethernet

Adapter to the EP/2

DB-37 connector

for connecting

to the EP/2

Electronics

Figure 2. Mounting screw locations on the

Ethernet Adapter

Step Procedure

4 Use the hex wrench to tighten the retaining screw in the

mounting post on the right side to secure the EP/2 electronics

assembly to the baseplate.

§The left retaining screw cannot be used with the Ethernet

Adapter installed.

Checking Installation

To check the installation, monitor the five status light-emitting diodes (LEDs) on

the face of the Ethernet Adapter.

§The Good Link status LED will blink once when power is supplied to the

EP/2. After several seconds it will remain lit, indicating that the network is

correctly wired and configured and working properly.

§The Polarity status LED, when lit, indicates that the network wiring polarity is

reversed. The adapter will continue to function. Check the Ethernet network

cable wiring and correct the polarity.

§The Receive and Transmit status LEDs flash on and off intermittently to show

that communication is occurring if the EP/2 is communicating with the LAN.

§The Collision status LED blinks occasionally during normal communications.

If this LED blinks often or stays on for long periods it indicates a problem.

Monitor the Ethernet network’s operation on the EP/2’s display. Refer to Novar’s

Controls EP/2 Keypad and Display Instructions (Document No. 5601190).

LOGIC ONE®IS A REGISTERED TRADEMARK OF NOVAR CONTROLS CORPORATION.

ETHERNET®IS A REGISTERED TRADEMARK OF XEROX CORPORATION.

THE CONTENTS OF THIS DOCUMENT ARE SUBJECT TO CHANGE WITHOUT NOTICE.

PRINTED IN THE U.S.A.

NOVAR CONTROLS CORPORATION

6060 ROCKSIDE WOODS BLVD., CLEVELAND, OH 44131

TEL.: 800.348.1235 WWW.NOVARCONTROLS.COM

4Doc. #569040000—A 7/30/04

Ethernet®Adapter Installation Instructions

Indice

Manuali Adattatore popolari di altre marche

PCB Piezotronics

PCB Piezotronics 090B274 Manuale utente

Auvidea

Auvidea J20 Manuale del prodotto

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manuale utente

Akribis

Akribis ITF-21-BISS-MIT Manuale utente

Tenda

Tenda W54U Manuale utente

ROHO

ROHO AGILITY Manuale utente

PROLiNK

PROLiNK WN2001 Manuale utente

Hawking

Hawking HUF2 Manuale utente

Airlink101

Airlink101 AWLC4030 Manuale utente

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manuale utente

Philips

Philips SWA4554S/10 Manuale utente

JVC

JVC TS-C9D2B Manuale di istruzioni

NETGEAR

NETGEAR A6100 Manuale utente

D-Link

D-Link DWA-121 Manuale utente

Philips

Philips SWA2037 Manuale utente

Basalte

Basalte 0610-20 Manuale utente

Yealink

Yealink EHS40 Manuale utente

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manuale utente