Numatic Floorcare tt 1840 Manuale utente

Trouble Shooting and Help Guide

TT / TTB 1840

FloorCare

PROBLEM CAUSE SOLUTION

Machine will not operate. Missing or blown fuses.

Battery not connected.

Low battery charge.

Replace fuse.

Connect Battery.

Charge.

Vacuum will not operate. Vacuum not turned on. Turn on.

Poor water pick-up. Waste-water tank full.

Blocked vacuum hose.

Loose hose.

Basket lter blocked.

Separator lter blocked.

Poor separator seal.

Damaged separator seal.

Damaged vacuum hose.

Damaged oor-tool blades.

Low battery charge.

Empty.

Clean.

Tighten.

Clean.

Clean and ret.

Renew.

Recharge.

No brush / Scrub function. No brushes tted.

Brush overloaded.

Check and t.

Reset.

Little or no water ow. Clean-water tank empty.

Clean-water tank lter blocked.

Incorrect water ow setting.

Fill.

Clean.

Adjust tap as desired

Machine just ‘stops’ while

operating.

To much load on the brush system.

Blown fuse in battery pack.

Reset, decrease the brush load.

Replace 40 Amp fuse.

The 1840 has been designed to scrub and dry a variety of hard oors.

This machine has not been designed to pick up large objects, make sure you pre-sweep the oor before use.

For optimum performance make sure you keep the lters, hoses and oor tool blades clean and free from debris.

Disconnect from the power supply or remove the battery BEFORE commencing cleaning or maintenance.

After every time the machine is used.

The machine should be left in a clean and tidy state, drain

all uids, clean all lters, pipes and place the

battery on charge.

It is recommended you strip and

thoroughly clean the machine and its

components regularly.

At least weekly to avoid operating

troubles and machine breakdowns.

Fitting Brush, Filling Machine, Water Tap, Raising the Floor Tool Using Machine, Brush Overload, Battery Fuse Storage, Cleaning Floor tool and Inlet tube

Draining Top Tank, Draining Bottom Tank, Clean Water Filter Clean Separator, Removing Top Tank Remove Bottom Tank, Re-assembling Machine Battery Care

Make sure you read and fully

understand your 1840 manual

before using the machine.

Fitting brush, Filling machine, Clean water tap and Raising oor tool...

Clean Water Tap...

Fitting the brush...

Located on the left of the machine is the clean

water tap, make sure the tap has been turned

on before use.

Index page...

The machine uses a 400mm brush or a

360mm pad drive.

Fit the brush pad onto the Nulock drive and

twist to lock in place.

Filling tank...

Remove the ller cap and ll using a hose,

bucket or suitable container.

Fill the clean water tank to a maximum of 18

litres including chemical if required.

Fill gauge...

Fitted to the clean water inlet

is a red plastic ll gauge, this

shows the tank full.

Moving when full...

When the clean water tank is full the machine

can be tilted to a maximum of 450 without

spillage.

Take care to make sure that contaminants (leaves, hair, dirt, etc.) are not allowed to enter the clean water tank.

Ideally set the tap to 45% this enables the

cleaning solution to last the same time as a

fully charged battery..

Off

45%

Raising and lowering the Floor Tool...

To raise and lower the oor tool make sure the

oor tool is central to the machine.

Lift the handle near the base of

the handle to raise the oor tool

and lock in position.

Fitting Brush, Filling Machine, Water Tap, Raising the Floor Tool Using Machine, Brush Overload, Battery Fuse Storage, Cleaning Floor tool and Inlet tube

Draining Top Tank, Draining Bottom Tank, Clean Water Filter Clean Separator, Removing Top Tank Remove Bottom Tank, Re-assembling Machine Battery Care

Operating Switches and Overload / Fuses

Operating Switches...

Hi - Lo Setting

The 1840 machine provides a choice of both high and low speeds.

To activate the control panel: press the Mode select button or press a trigger on the handle.

The battery pack comes tted with a 40 amp fuse, replace the fuse using Numatic approved part (208526) if required.

Index page...

Battery Pack Fuse...

Press the mode select button again to get vacuum only.

The On / Off Switch and triggers are not required in this mode. (g 3)

Press the mode select button to switch this mode off and return to default mode.

The panel if unused will automatically turn off after 60 seconds.

Brush Overload...

The brush motor will cut out and the Hi / Lo light will ash if the brush motor has been overloaded (g 4).

Releasing the handle triggers will allow the machine to reset.

Mode Button

To start: hold down either trigger and press the yellow On / Off switch once.

Whilst the brush motor is running press the water ow On / Off button for uid control (g 1), the clean water On / Off tap must be open.

When the Triggers are released the brush motor and the cleaning solution pump will switch off, the vacuum motor will continue for 10 seconds.

Press the mode select button to operate the brush only (g 2).

The start sequence is required in this mode.

The water ow On / Off button will operate in this mode.

If the brush motor keeps overloading consider using a different type of brush.

Heavy brush load decreases the available battery run time.

Fitting Brush, Filling Machine, Water Tap, Raising the Floor Tool Using Machine, Brush Overload, Battery Fuse Storage, Cleaning Floor tool and Inlet tube

Draining Top Tank, Draining Bottom Tank, Clean Water Filter Clean Separator, Removing Top Tank Remove Bottom Tank, Re-assembling Machine Battery Care

Index page...

Make sure the oor tool inlet is not blocked

(g 1).

Brushes, Floor tool and Inlet tube...

Storage ...

Numatic recommend you leave your 1840 resting on the brush if leaving for machine for

short periods of time.

This saves distorting the squeeze blades.

Remove the brush and oor tool if you are leaving the machine for extended periods of

time.

Floor tool and inlet tube...

1 3

The oor tool can also be stripped and cleaned.

Clean the oor tool blades, replace if damaged and clean the castors.

Replace is a reverse of the removal procedure, making sure the slotted blade goes to the front of the machine.

The oor tool can be removed by swinging it to

the right side of the machine (g 2)...

And undoing the retaining knobs (g 3).

It is important to make sure the oor tool is properly maintained for reliable water pick up.

After every time your machine is used, we recommend you drain all uids, clean all

lters, pipes and place the battery on charge.

The machine should be left in a clean and tidy state.

Fitting Brush, Filling Machine, Water Tap, Raising the Floor Tool Using Machine, Brush Overload, Battery Fuse Storage, Cleaning Floor tool and Inlet tube

Draining Top Tank, Draining Bottom Tank, Clean Water Filter Clean Separator, Removing Top Tank Remove Bottom Tank, Re-assembling Machine Battery Care

Drain Top (Waste) Tank

Use the drain hose to empty the top tank and ush the tank through with clean water, it is

advisable to let the tank air dry, by removing the separator, if leaving your machine for extended

periods of time.

Drain Bottom (Clean Water) Tank

Located on the left of the machine is the yellow bottom tank drain cap.

Drain the clean water tank if leaving your machine for a extended period.

Note... Do not over tighten the yellow drain cap, this can not only cause the

plastic to split, but make it extremely hard to remove the next time you want to

drain the tank. The cap has a rubber seal and might require a spanner to remove.

Index page... Regular Maintenance...

*Note:- Machine side cut away for clarity.

Located under the clean water inlet is the clean water lter.

Cleaning chemicals residue can cause the lter to become blocked causing

poor water ow.

Remove the clean water inlet (g 1).

On the bottom of the tank is the clean water lter, clean the lter regularly

(g 2).

(Clean Water) Tank Filter...

1 2

If you require further training or

assistance contact your supervisor

Fitting Brush, Filling Machine, Water Tap, Raising the Floor Tool Using Machine, Brush Overload, Battery Fuse Storage, Cleaning Floor tool and Inlet tube

Draining Top Tank, Draining Bottom Tank, Clean Water Filter Clean Separator, Removing Top Tank Remove Bottom Tank, Re-assembling Machine Battery Care

Remove and clean the separator...

Index page... Regular Maintenance...

The separator has a sealing rubber which should be cleaned and inspected at every cleaning of the machine (g 1).

Also remove the two lters clipped into the separator and ush with clean water.

Replace by tting the rear of the lter rst then clipping the front to lock in place (g 2).

If you are leaving the machine for a long period leave the separator off, allowing the machine to air dry. Replace before commencing cleaning.

1 2

Remove the top (dirty water) tank...

Disconnect and remove the battery before proceeding with tank removal.

Once emptied the top (dirty water) tank can be simply lifted off the machine.

If you require further training or

assistance contact your supervisor

Fitting Brush, Filling Machine, Water Tap, Raising the Floor Tool Using Machine, Brush Overload, Battery Fuse Storage, Cleaning Floor tool and Inlet tube

Draining Top Tank, Draining Bottom Tank, Clean Water Filter Clean Separator, Removing Top Tank Remove Bottom Tank, Re-assembling Machine Battery Care

Index page...

Removing the bottom (clean water) tank...

Once the Bottom (clean water)Tank has been emptied the tank can be removed, this involves rstly disconnecting the water feed pipe from the

clean water tap.

Note which way the clean water pipe and the black suction pipes are routed as they will have to be re-routed the same way on re-assembling.

Lift the bottom tank making sure the black suction hose passes through the tank. Remove the suction hose from the inlet tube.

Once the machine is stripped you can clean all tubes, pipes and lters.

It is recommended that you carry out this procedure once a week.

Re-assembling the machine...

Ret the oor tool vacuum hose and feed the hose through the bottom tank, place the bottom tank onto the base.

Make sure the water feed pipe locates in the channel moulded into the base of the tank.

Connect the water feed pipe to the tap.

Place the oor tool vacuum hose as shown and ret the top tank. Ret the Separator and reconnect the vacuum and separator hoses.

If you require further training or

assistance contact your supervisor

Regular Maintenance...

Fitting Brush, Filling Machine, Water Tap, Raising the Floor Tool Using Machine, Brush Overload, Battery Fuse Storage, Cleaning Floor tool and Inlet tube

Draining Top Tank, Draining Bottom Tank, Clean Water Filter Clean Separator, Removing Top Tank Remove Bottom Tank, Re-assembling Machine Battery Care

Battery Care...

Battery charging...

Index page...

Use recommended PPE as required...

Please comply with your company’s COSHH risk assessments

(Make sure you wear the appropriate safety clothing).

Leave the machine empty and clean...

Open the separator and let the machine air dry...

Only leave the machine resting on the brush and oor tool for short periods of time...

If you require further training or

assistance contact your supervisor

Manufactured by

Numatic International

Chard, Somerset. TA20 2GB

01460 68600

We have had cases where operatives have plugged the charger into the machine (g 1) instead of the battery (g 2), this will not charge the battery, but will cause damage to the

machine.

Disconnecting the Charger.

Make sure you use the connector handles tted to the grey plug when disconnecting the machine, avoid pulling on the electrical cables, as this can cause damage to the cable

(g 3).

Recharge the battery fully after its last use.

Do not leave the battery in a discharged state.

1 32

MED-000610 08/15 (A01)

Fitting Brush, Filling Machine, Water Tap, Raising the Floor Tool Using Machine, Brush Overload, Battery Fuse Storage, Cleaning Floor tool and Inlet tube

Draining Top Tank, Draining Bottom Tank, Clean Water Filter Clean Separator, Removing Top Tank Remove Bottom Tank, Re-assembling Machine Battery Care

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Numatic Macchina per pavimenti

Numatic

Numatic TWINTEC CABLE TT4055 Manuale di installazione e funzionamento

Numatic

Numatic LoLine NLL 415 Manuale utente

Numatic

Numatic TTB-665 Manuale utente

Numatic

Numatic TTB-455 Manuale utente

Numatic

Numatic TT-3450S Manuale utente

Numatic

Numatic HNS1550G Manuale utente

Numatic

Numatic TWINTEC BATTERY ETB4045 Manuale di installazione e funzionamento

Numatic

Numatic TTB 345S Manuale utente

Numatic

Numatic NPR 1515/S Manuale utente

Numatic

Numatic LoLine NLL 332 Manuale utente

Numatic

Numatic TTB 1840 Manuale utente

Numatic

Numatic NuSpeed NR-1500 Manuale utente

Numatic

Numatic Nacecare TT 1117 / 100 Manuale utente

Numatic

Numatic TTB 4055/100 Manuale utente

Numatic

Numatic HFS 1023 Manuale utente

Numatic

Numatic NuSpeed NR-1500 Manuale utente

Numatic

Numatic TTB 2120/100T Manuale utente

Numatic

Numatic TTB 1117/100 Manuale utente

Numatic

Numatic NuSpeed NR-1500 Manuale utente

Numatic

Numatic TT 345 Manuale utente

Numatic

Numatic TTB 4055/100 Manuale utente

Numatic

Numatic TTB-1620 Manuale utente

Numatic

Numatic NV-450 Manuale utente

Numatic

Numatic TTV 4555 Manuale utente

Manuali Macchina per pavimenti popolari di altre marche

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Manuale utente

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Manuale utente

Mytee

Mytee 8070 Mytee-Lite Manuale utente

Kärcher

Kärcher B 140 R Manuale utente

Triple S

Triple S Ace 26T1 Manuale utente

Nilfisk-Advance

Nilfisk-Advance SW 750 Manuale utente

Tornado

Tornado Marathon 2000 98190 Manuale

Windsor

Windsor ADMIRAL Admiral 8 Manuale utente

Tennant

Tennant 8210D Manuale utente

Nobles

Nobles Frontier Manuale del prodotto

lavina

lavina 21-X Manuale utente

KENT

KENT Edge 28B Manuale utente

Tennant

Tennant 215 Manuale del prodotto

Windsor

Windsor BDP 51/2000C Manuale utente

CleanFreak

CleanFreak DURA-18HD Manuale utente

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Guida per l'amministratore

BETCO

BETCO PB24 Manuale utente

IPC

IPC CT51-71 BT Manuale utente

Numatic floorcare tt 1840 Manuale utente

Manuali Macchina per pavimenti popolari di altre marche