NZXT LIFT Manuale utente
LIFT
LIGHTWEIGHT AMBIDEXTROUS MOUSE
ENGLISH
VERSION 2.0
TABLE OF CONTENTS
1. ..................................................................... 02
INTRODUCTION
4. ................................................................... 05
SETTING UP
THE MOUSE
2. .................................................................... 03
ABOUT THE LIFT MOUSE
5. ...................................................................06
CHANGING LIGHTING
AND PROFILES
3. ...................................................................04
PACKAGE CONTENTS &
DESCRIPTION
6. ................................................................... 07
7. .................................................................... 08
8. .................................................................. A-1
APPENDIX
USING THE NZXT LIFT
MOUSE WITH CAM
SOFTWARE
USING THE LIFT MOUSE
IN HARDWARE MODE
05
LIFT
1. Connect the USB Cable to any available USB 2.0 (or faster) port on
your PC.
2. Choose a DPI setting that matches your preference by a short press
of the DPI button - there are several dierent default settings that
can be cycled through, from low to high sensitivity.
3. DPI settings can be further customized within NZXT CAM software
(for example, as a user you may only need one DPI setting, or just
a few, depending on your preference). Within CAM you may reduce
the number of customized settings and store them onto your mouse
under a profile. (see section 5, below).
4. Although the Lift Mouse will operate on nearly any surface, a mouse
pad or mat is recommended for optimal tracking.
4. SETTING UP THE MOUSE
E
Refer to the diagram by stating the DPI button is “E”
06
LIFT
CYCLING THROUGH DEFAULT LIGHTING SETTINGS
1. Using a long press of the DPI button (one to three second press), you
may cycle through several pre-programmed lighting modes.
2. By downloading and activating the NZXT CAM software, users may
utilize up to four on-board profiles which can have various settings
associated with each profile that will store custom DPI settings,
macros, and lighting. These settings are automatically activated
when changing to a specific profile using a long press of the DPI
button.
3. Once profiles and settings are loaded onto the Lift Mouse with NZXT
CAM, it is possible to operate the mouse without running software.
You may also transfer the mouse between dierent computers using
the settings stored on-board the mouse.
5. CHANGING LIGHTING AND PROFILES
E
Refer to the diagram by stating the DPI button is “E”
07
LIFT
6. USING THE NZXT LIFT MOUSE WITH CAM SOFTWARE
A. DOWNLOADING AND INSTALLING CAM SOFTWARE
Go to nzxt.com/software/cam for the latest version of CAM
B. SETUP OF CAM PROFILES AND STORING ON THE KEYBOARD
The Lift Mouse has four onboard profiles that can be setup and stored via
CAM software. After profile information is stored, it is not necessary to run
CAM to operate stored lighting, macros, etc.
C. CONTROLLING PROFILE SWITCHING
Depressing the DPI button for one to three seconds (long press) will
change to the next stored profile (1 through 4, respectively).
D. LIGHTING MODES
There are four default lighting modes stored on profiles #1 through #4 and
can be cycled through by a long press of the DPI button.
E. CUSTOMIZING RGB LIGHTING
By using CAM/Mouse/Lighting, users are able to customize lighting, and
set up lighting under profiles (if desired), as described in SECTION B.
F. CUSTOMIZING KEYBOARD MACROS
By using CAM/Mouse/Macros, users are able to create both simple and
complex macros, and store them under profiles (if desired), as described in
SECTION B.
G. REBINDING KEYS
By using CAM/Mouse/Key Remapping, users are able to create new and
customized button bindings, and store them under profiles (if desired), as
described in SECTION B.
08
LIFT
7. USING THE LIFT MOUSE IN HARDWARE MODE
A. CONTROLLING RGB LIGHTING
1. There are four default lighting modes stored on profiles #1 through
#4 and can be accessed by cycling through with a long press of the
DPI button. If customized lighting has been set up, and assigned
custom lighting to one of the onboard profiles, custom lighting will
activate when switching to a custom profile.
B. SWITCHING TO STORED PROFILES (1-4)
2. Depressing the DPI button (long key press) will cycle through all
active profiles. E
A-1
LIFT
8.5 Revision History................................................................ A-13
8. APPENDIX
8.2 NZXT Global Warranty Policy ................................ A-3
8.3 Support and Service....................................................... A-9
8.4 Regulatory Notices........................................................ A-12
8.1 SUPPORT.................................................................................... A-2
Indice
Altri manuali NZXT Topo
