O'Neal Microflash 4T Manuale utente
User's Guide
MICROFLASH 4T
TABLE OF CONTENTS
3
microFlash 4t Printer: Top View 4
Installing a Radio Card 5
Using Batteries: General Guidelines 6
Installing and/or Replacing Batteries 6
Charging the Battery 7
Determining Battery Condition 7
Installing Paper 8
Printing a Self-Test 10
Configuring the Printer 10
Using Printer Data Cables 10
Using 802.11b/Bluetooth 11
802.11b Parameters 11
Bluetooth Parameters 11
Using Buttons, LEDs, and Audio Indicators 12
Button Functions 12
LED Indicators 12
Blue RF Power LED Indicators 12
Charge LED Indicators 13
CardReader LED Indicators 13
Audio Indicators 14
CardReader Audio Indicators 14
Using a CardReader 15
General Guidelines 15
Supplies 18
Media Supplies 18
MICROFLASH 4T PRINTER USER'S GUIDE
4
microFlash 4t Printer: Top View
Roller
Paper/Paper
Cavity
Power Port
Battery Retaining Clip
Battery/Battery Well
Self-Test Button
RF/Power Button/LED
Charge LED
Print Head
Release Lever
Data Port
Figure 1
MICROFLASH 4T PRINTER USER'S GUIDE
5
Installing a Radio Card
1. Remove the radio card cap (Figure 2).
2. With the logo facing down, insert the radio card
between the foam and the radio card strap
(Figure 3).
3. Carefully push the card into the connector until it is
fully seated (Figure 4).
4. Replace the radio card cap.
5. For information on configuring the radio, see
Configuring the Printer on page 10
.
6. Install the batteries. For more information, see
Installing and/or Replacing Batteries on page 6
.
Note: The following information applies to printers
with radio capabilities.
Caution: Before installing the radio card, verify the
red, battery isolator labels are in place or remove the
batteries before installing the radio card.
Figure 2 Figure 3
Figure 4
MICROFLASH 4T PRINTER USER'S GUIDE
6
Using Batteries: General Guidelines
If your printer came with batteries already installed,
remove the red, battery isolator labels. If your
printer did not come with batteries installed, see
Installing and/or Replacing Batteries on this page
.
If you are storing your printer for a long period of
time, reinstall the battery isolator labels.
Both batteries must be installed for your printer to
operate properly.
Installing and/or Replacing Batteries
1. Open the printer's cover (Figure 5).
2. If applicable, remove the batteries by pressing the
retainer clip outward with your thumb (Figure 6).
3. While pressing the retainer clip, lift the outside end
of the battery past the retainer clip.
4. Insert or replace the new batteries. Verify the
battery contacts are facing down and are on the
outside edge of the printer (Figure 7).
Figure 5 Figure 6
Figure 7
MICROFLASH 4T PRINTER USER'S GUIDE
7
Charging the Battery
To charge the battery, you must first remove the red,
battery isolator labels.
If the battery is low when the printer “wakes up,” the
printer sounds three short beeps. Plug the AC Adapter
into an appropriate power source. The Charge LED
turns red when charging and turns green when fully
charged. (For more information on the Charge LED, see
Using Buttons, LEDs, and Audio Indicators on page 12
.)
A complete charge takes approximately 2 to 4 hours.
Determining Battery Condition
To determine the battery’s condition, print a self-test.
For more information, see
Printing a Self-Test on
page 10
. The battery voltage varies between 6.2 and
8.4 volts.
Caution: To obtain full battery capacity, a new battery
must cycle through two to three charges. To restart a
charge, unplug the power cord. Wait 30 seconds, then
replug the power cord.
MICROFLASH 4T PRINTER USER'S GUIDE
8
Installing Paper
1. Insert a roll of paper with the end of the roll exiting
from the bottom of the paper cavity (Figure 8).
2. Open the print head by raising the gray, print head
release lever until it is fully open. Do not stop at the
partial open position (Figure 9).
3. Wake up the printer by briefly pressing the red, self-
test button (Figure 10).
4. Feed the end of the paper under the roller. The
paper automatically feeds under the roller and exits
the top of the print head. Verify the paper exits the
print head straight (Figure 11).
Figure 8 Figure 9
Figure 10 Figure 11
MICROFLASH 4T PRINTER USER'S GUIDE
9
5. Lower the gray, print head release lever (Figure 12).
6. Feed the paper through the printer's cover
(Figure 13).
7. Close and latch the printer's cover.
Figure 12 Figure 13
MICROFLASH 4T PRINTER USER'S GUIDE
10
Printing a Self-Test
1. After installing the paper, open the printer's cover.
2. Press and hold the red, self-test button for
approximately five seconds until printing begins.
3. After printing begins, release the red, self- test
button.
Configuring the Printer
The printer has many configurable settings. To
configure or upgrade firmware, download the Windows
configuration program at www.oneilprinters.com.
Using Printer Data Cables
1. Select the appropriate cable for use with the host
and/or device you are using.
2. Insert the plug into the printer's data port
(Figure 14).
3. Lead the cable through the notch on the outside of
the printer's cover.
4. With the cable exiting the front of the printer, close
and latch the printer's cover.
Caution: If the red, battery isolator labels are
installed, remove them.
Figure 14
Indice
