Oasis FSC463R Istruzioni per l'installazione

SCC P/N

20-30109

READ AND SAVE THESE INSTRUCTIONS

Rev C Date: 10.1.2019

I:\Oper Manual\Oasis\FSC463R Ref Grab-N-Go 20-30109.pub

Merchandiser Shown With Product

For Illustrative Purposes Only

MODEL FSC463R REFRIGERATED GRAB-N-GO MERCHANDISER

888 E. Porter Road ∙ Muskegon, MI 49441 Phone: 231.798.8888 Fax: 231.798.4960 www.structuralconcepts.com

INSTALLATION &

OPERATING MANUAL

TABLE OF CONTENTS

OVERVIEW / TYPE / COMPLIANCE / WARNINGS / PRECAUTIONS / WIRING DIAGRAM ..............

REMOVAL OF CASE FROM SKID / POSITIONING UNIT ..…………..…………………………………..

ADJUSTING LEVELERS ………………………………………………...………………………………...….

FIELD WIRING BOX / ACCESS / PANEL REMOVAL / MAIN POWER SWITCH / TEMP. CONTROL

CEILING ORIGINATED ELECTRICAL & REFRIGERATION LINES / KNOCKOUT REMOVAL /

SEALING ……………………………………………………………………………………………….

MODEL FSC463R PLAN-O-GRAM (LOAD LEVEL GUIDELINES) ..…………………………………….

DIGITAL THERMOMETERS / SECURITY COVER INSTALLATION & REMOVAL …………..…..…...

POWER-UP CHECK (EVAPORATOR FAN AREA) ...……………………………………………………..

MAINTENANCE FUNDAMENTALS: NON-ADJUSTABLE SHELF / BRACKET ASSEMBLY ...…….

MAINTENANCE FUNDAMENTALS, CONTINUED: LED LIGHT FIXTURES / REMOVAL /

REPLACEMENT ………………………………………………………………………………...……..

REFRIGERATION FUNDAMENTALS: UNDERSIDE LAYOUT (BOTH SELF-CONTAINED &

REMOTE) ……………………………………………………………………………………………….

REFRIGERATION FUNDAMENTALS: SELF-CONTAINED UNIT ILLUSTRATED PARTS

BREAKDOWN ………………………………………………………………………………………….

GENERAL CLEANING (TO BE PERFORMED BY STORE PERSONNEL) - EXTERIOR / INTERIOR

GENERAL CLEANING (TO BE PERFORMED BY TRAINED SERVICE PROVIDERS ONLY) …..….

TROUBLESHOOTING (TO BE PERFORMED BY STORE PERSONNEL UNLESS STATED

OTHERWISE) …………………………………………………………………………………………..

TROUBLESHOOTING (TO BE PERFORMED BY TRAINED SERVICE PROVIDERS ONLY) ……….

TROUBLESHOOTING (BY TRAINED SERVICE PROVIDERS ONLY) - CONDENSING SYSTEM

TROUBLESHOOTING (BY TRAINED SERVICE PROVIDERS ONLY) - EVAPORATOR SYSTEM

PREVENTIVE MAINTENANCE (TO BE PERFORMED BY TRAINED SERVICE PROVIDERS) …….

PREVENTIVE MAINTENANCE: HONEYCOMB AIR DIFFUSERS (TO BE PERFORMED BY

TRAINED SERVICE PROVIDERS ONLY) .………………………………………………………...

SERIAL LABEL LOCATION & INFORMATION LISTED / TECH INFO & SERVICE………………......

CAREL® CONTROLLER - PROGRAMMING THE INSTRUMENT….……………………...….…….......

CAREL® CONTROLLER - USER INTERFACE, SUMMARY TABLES OF ALARMS & SIGNALS ….

CAREL® CONTROLLER - Summary Table of Operating Parameters (After Programming Key) .

TECHNICAL SERVICE CONTACT INFORMATION & WARRANTY INFORMATION ..…………….....

3-4

19-20

OVERVIEW

 These Structural Concepts merchandisers are

designed to merchandise packaged products at 41 °F

(5 °C) or less product temperatures.

 Cases should be installed and operated according to

this operating manual’s instructions to ensure proper

performance. Improper use will void warranty.

TYPE 1 vs. TYPE 2 CONDITIONS

This unit is designed for the display of products in ambient

store conditions where temperatures and humidity are

maintained within a specific range.

 Self-Contained cases are designed for Type 1

conditions: Ambient conditions at 55% maximum

humidity and maximum temperatures of 75 °F (24 °C).

 Remote cases are designed for Type 2 conditions:

Ambient conditions at 55% maximum humidity and

maximum temperatures of 80 °F (27 °C).

 If unsure if your case is designed for Type 1 or Type 2

conditions, see identifier label on your case. Location

may vary.

COMPLIANCE

 Performance issues when in violation of applicable

NEC, federal, state and local electrical and plumbing

codes are not covered by warranty. See below.

WARNINGS

 This sheet contains important warnings to prevent

injury or death. Please read carefully!

PRECAUTIONS, MAINTENANCE & WIRING DIAGRAM

INFORMATION

 See next page for PRECAUTIONS, MAINTENANCE

and WIRING DIAGRAM information.

WARNING

Hazardous moving parts. Do not operate unit with covers removed.

Fan blades may be exposed when deck panel is removed.

Disconnect power before removing deck panel.

WARNING

Risk of electric shock. Disconnect power before servicing unit.

CAUTION! More than one source of electrical supply is

employed with units that have separate circuits.

Disconnect ALL ELECTRICAL SOURCES before servicing.

WARNING

ELECTRICAL

HAZARD

WARNING

KEEP

HANDS

COMPLIANCE

This equipment MUST be installed in compliance with

all applicable NEC, federal, state and local

electrical and plumbing codes.

OVERVIEW / TYPE / COMPLIANCE / WARNINGS / PRECAUTIONS / WIRING DIAGRAM - PAGE 1 of 2

WARNING! POWER CORD AND PLUG MAINTENANCE

Risk of electric shock. If cord or plug becomes damaged,

replace only with cord and plug of same type.

WARNING: This product can expose you to chemicals, including

Urethane (Ethyl Carbamate), which are known to the state of

California to cause cancer and birth defects or other reproductive

harm. For more information go to P65Warnings.ca.gov.

OVERVIEW / TYPE / COMPLIANCE / WARNINGS / PRECAUTIONS / WIRING DIAGRAM - PAGE 2 of 2

CAUTION! GFCI BREAKER USE REQUIREMENT

If N.E.C. (National Electric Code) or your local code

requires GFCI (Ground Fault Circuit Interrupter) protection,

you MUST use a GFCI breaker in lieu of a GFCI receptacle.

CAUTION! ADVERSE CONDITIONS / SPACING ISSUES

 Performance issues caused by adverse conditions are NOT warranted.

 End panels must be tightly joined or kept at least 6-inches away from

any structure to prevent condensation.

 Unit must be kept at least 15-feet from exterior doors, overhead HVAC

vents or any air curtain disruption to maintain proper temperatures.

 Unit must not be exposed to direct sunlight or any heat source

(ovens, fryers, etc.).

 Keep at least 8-inch clearance above unit for air discharge

(self-contained units only).

CAUTION

CAUTION! LED LAMP REPLACEMENT GUIDELINES

LED lamps reflect specific size, shape and overall design.

Any replacements must meet factory specifications.

CAUTION

PRECAUTIONS

 This sheet contains important precautions to prevent

damage to unit or merchandise.

 Please read carefully!

 See previous page for specifics on OVERVIEW,

CONDITION TYPE, COMPLIANCE and WARNINGS.

WIRING DIAGRAM

 Each case has its own wiring diagram folded and in its

own packet.

 Wiring diagram placement may vary; it may be

placed near ballast box, field wiring box, raceway

cover, or other related location.

REFRIGERANT DISCLOSURE STATEMENT

 This equipment is prohibited from use in California

with any refrigerants on the “List of Prohibited

Substances” for that specific end-use, in accordance

with California Code of Regulations, title 17, section

95374.

 This disclosure statement has been reviewed and

approved by Structural Concepts and Structural

Concepts attests, under penalty of perjury, that these

statements are true and accurate.

CAUTION! WATER ON FLOOR CAN CAUSE EXTENSIVE DAMAGE

Before powering up unit:

 Check that drain lines flow directly to floor drain.

 Units with optional Clean Sweep™ MUST be properly connected.

1. Remove Unit From Skid

For your safety, the equipment is furnished with

a properly grounded cord connector. Do not

attempt to defeat the grounded connector.

 Caution! Remove BOTH lower panels from case

before removing from skid to prevent buckling.

 Illustrations below show case being removed

from skid.

REMOVAL OF CASE FROM SKID / POSITIONING UNIT

 Place case in proper location.

 Plug cord into certified electrical outlet with ground.

2. Positioning Unit

 Place unit into desired location before leveling.

 See next page for specifics about leveling.

Slide Skid Out

From Under

Case

ADJUSTING LEVELERS

Adjust Levelers

 After case is in position, adjust case so it is level

and plumb.

 You may need to remove front and/or rear

toe-kick to access levelers.

 Use adjustable wrench (and/or a pry bar) to adjust

leveler.

 Do not use Pry Bar on Toe-Kick as it will buckle.

 Do not use Pry Bar on End Panel. It may chip.

 Use Pry Bar ONLY on Base Frame to avoid

damaging case.

Pry Bar

FIELD WIRING BOX / ACCESS / PANEL REMOVAL / MAIN POWER SWITCH / TEMP. CONTROL

1. Field Wiring Box / Access

 Warning! Turn power off and/or disconnect

power before providing maintenance and

service to unit.

 Assembly/disassembly/servicing to be

performed by licensed electrical contractor.

 Panel must be removed to access field wiring box

and main power switch.

 See illustration below.

2. Panel Removal

 To remove panel (and access field wiring box), lift

panel up and off case hooks by grasping firmly

and pulling up and outward.

 See illustration at top-right.

Field Wiring /

Ballast Box

Thermostat Controller &

Main Power Switch

Main Power

Switch

3. Main Power Switch

 For self-contained cases, the main power switch

controls power to entire case.

 If main power switch is not turned on, lights will

not turn on NOR will refrigeration components

operate.

 See illustration below.

4. Temperature Control

 Illustration below shows location of temperature

controller (after removal of front panel).

 See Carel Temperature Controller information

in this manual for specifics on settings.

Self-Contained Merchandiser

(Partially Disassembled)

Slots For Attaching

To Case Hooks

Removable Front Panel

CEILING ORIGINATED ELECTRICAL & REFRIGERATION LINES / KNOCKOUT REMOVAL / SEALING

1. Merchandiser Versatility

 Structural Concepts cases can accompany

either floor or ceiling-originated electrical and/or

refrigeration lines.

 This page shows how ceiling-originated lines

are routed into case.

2. Ceiling Routed Electrical/Refrigeration. Lines

 A center pass-through protective plate is mount-

ed at top of case over two (2) PVC center

pass-throughs.

 If electrical/refrigeration lines are ceiling-

originated, remove plate knockouts.

 Electrical and/or refrigeration lines may then be

dropped through PVC center pass-throughs.

 Caution! If ceiling-originated lines are used,

you MUST seal both upper and lower PVC

Center Pass-Through

Protective Plate Shown After

Removal of Knock-Outs

center pass-throughs (at entrance points) with

expandable foam sealant to prevent

condensation in case.

3. Plate Removal

 Note: Though not required, protective plate can be

removed from merchandiser via four (4) screws.

4. Case Underside

 See REFRIGERATION FUNDAMENTALS:

UNDERSIDE LAYOUT (BOTH

SELF-CONTAINED & REMOTE) section in this

manual for location of center pass-throughs at

underside of case.

Center Pass-Through Protective

Plate Mounted on Merchandiser

Caution! If ceiling originated lines are

used, you MUST seal both upper and

lower PVC center pass-throughs (at

entrance points) with expandable

foam sealant to prevent

condensation in case.

MODEL FSC463R PLAN-O-GRAM (LOAD LEVEL GUIDELINES)

Model FSC463R Plan-O-Gram (Load Level Guidelines)

> Note: Any changes to this document must also be made to Operating Manual P/N 20-30299

CAUTION! TO MAINTAIN SAFE PRODUCT TEMPERATURES AND AIRFLOW

CAREFULLY FOLLOW THESE GUIDELINES:

 DO NOT STACK PRODUCT NEARER THAN 1” TO UNDERSIDE OF PLENUM

 DO NOT STACK PRODUCT NEARER THAN 1” TO UNDERSIDE OF SHELVES

 DO NOT ALLOW PRODUCT TO HANG OVER FRONT OF SHELVES

 DO NOT STACK PRODUCT ON DECKS HIGHER THAN UNDERSIDE OF SHELF

 DO NOT ALLOW PRODUCT ON DECKS TO HANG OVER PRODUCT STOP

ACCEPTABLE

PRODUCT PLACEMENT

1” Min.

--- SIDE VIEW --- --- SIDE VIEW ---

Do Not Allow Product

On Decks To Hang

Over Product Stop

Do Not Stack Product

Nearer Than 1” To

Underside of Plenum

Do Not Stack Product On

Decks Higher Than The

Underside Of Lower Shelf

Do Not Stack Product

Nearer Than 1” To

Underside of Shelves

Do Not Allow Product

To Hang Over Front

of Shelves

Acrylic Air

Deflector

1” Min.

Product

Stop

SCC P/N 20-30299

NOTE: ANY

REVISIONS TO THIS

DOCUMENT MUST

ALSO BE MADE TO

SCC P/N 20-30299

UNACCEPTABLE

PRODUCT PLACEMENT

DIGITAL THERMOMETERS / SECURITY COVER INSTALLATION & REMOVAL

1. Digital Thermometers

Digital thermometers are located on rear plenum at

upper area of case.

 Digital thermometers are on BOTH side of case.

 See enlarged illustration at lower-left.

2. Security Cover Installation (Optional)

A. Place security cover inside lower retainer brack-

et. See illustration of random unit with lower

retainer bracket at below-right.

B. Lean security cover against header at top of unit.

C. With key inserted in the lock, rotate the locking

mechanism’s “flat bar” into the bracket with slot at

center of case. See illustration at top-right and

mid-right.

3. Security Cover Removal (Optional)

A. With key inserted in the lock, rotate the locking

mechanism’s “flat bar” out of the bracket with slot

(as shown in top-right illustration).

Digital

Thermometer

B. Lean security cover away from header at top of

unit.

C. Holding security cover handles (or grasping sides

of security cover, if no handles), lift security cover

up and away from header. See illustration

below-right

Security

Cover

Key & Locking

Mechanism

Locking

Mechanism With

“Flat Bar” To

Lock Into Slot

Bracket

With Slot

For Latch

Sample View of

Lower Retainer

Bracket (Rotated

For Illustrative

Purposes Only)

Header

Indice

Altri manuali Oasis Merchandiser

Oasis

Oasis FSC663R Manuale utente

Manuali Merchandiser popolari di altre marche

FRIGOGLASS

FRIGOGLASS Flex 20 HC Manuale utente

Hussmann

Hussmann ENTYCE TY3 Manuale utente

EPTA

EPTA COSTAN RHINO MULTI Manuale utente

Hussmann

Hussmann CRFD Istruzioni operative

CASCO

CASCO Nano Cube Manuale utente

Hussmann

Hussmann WDCHI Manuale utente

True

True GDIM-26 Manuale utente

Structural Concepts

Structural Concepts Oasis Mobile Series Istruzioni per l'installazione

Hussmann

Hussmann Q2-SS Istruzioni operative originali

Haussmann

Haussmann RL Manuale utente

Howard McCray

Howard McCray R-CDS32E-4 Manuale utente

Hussmann

Hussmann microSC SHM-A Series Manuale utente

Hussmann

Hussmann APT0500 Manuale utente

EPTA

EPTA iarp Cool Emotions Delight Lite Manuale utente

VALERA

VALERA BC 85 Manuale utente

HL Display

HL Display 3eBin Manuale utente

Hussmann

Hussmann Q1-SS Manuale di istruzioni

Hussmann

Hussmann impact Excel C2X-XLEP Manuale di istruzioni