Oben BA Series Manuale utente

BASeries

Single Action Ballhead

You’reonsteadyground™

Thank You forchoosingOben!

This Oben BA Series ballhead is a compact and

lightweight head that provides nimble, reliable

operation. The single lock makes it easy to rapidly

adjust the ball and calibrated base. A snap-in quick-

release plate is included for eortless mounting

and dismounting of the camera. The dual-locking

quick-release keeps the camera securely attached

to the ballhead and prevents the camera from being

accidentally released. For additional security, the

ballhead is constructed with extra tension to oer

greater control when repositioning the camera.

Integrated bubble levels ensure accurate alignment

of the camera with the horizon. The calibrated base

of the ballhead allows for full 360° panning, as well

as precise placement of the camera.

Please read through this entire manual before using the

BA series ballhead.

Note: Images are for illustrative purposes only. Actual

product may vary.

INTRODUCTION

Key Features 4

MountBallheadToTripod 5

Converting MountingThread 5

MainLockingKnobOperation 5

Calibrated Base 6

Dual-LockingQuick-Release 6

MountQuick-Release Plate 6

MountCamera 7

Warnings 7

TABLE OF CONTENTS

Quick-ReleasePlate

Dual-LockingQuick-Release

SingleLock

1/4″-20 UNCMounting Screw

BaseWith 360° Markings

Bubblelevels

90°Groove

KEY FEATURES

The single Locking Knob locks

and unlocks the ballhead, which

allows you to change the position

of the camera. When changing

camera position using the Locking

Knob, always keep one hand

on the camera. Turn the knob

counterclockwise to unlock the

head and clockwise to lock it.

Ensure that the knob is ﬁrmly

tightened before letting go of the

camera.

For tripods with a 1/4″threaded

mounting stud: insert the

supplied Reducer Bushing into

the threaded mounting hole of the

head to enable a proper ﬁt.

OPERATION

To mount the ballhead on the

tripod, ﬁrst tighten the locking

knob on the head. Then, being

careful to properly align the

tripod stud and the ballhead hole

to avoid damaging them, rotate

the ballhead clockwise onto the

tripod, and tighten it by hand.

1.Mount BallheadTo Tripod

2.ConvertingMountingThread

3.Main LockingKnobOperation

The BA series is designed with

a dual-locking quick-release

latch to keep the camera

securely in place on the head.

To unlock the quick-release,

press the small latch while

pulling outward on the main

latch at the same time.

Mount the Quick-Release Plate

to the threaded hole on the

base of your camera. The plate

utilizes a 1/4″-20 screw that

will ﬁt most cameras. After

tightening the screw, fold the

thumbscrew ﬂat against the

bottom of the quick-release plate.

The base of the ballhead can

be rotated a full 360° and

is controlled by the single

locking knob on the side of

the ballhead. Twist the knob

counterclockwise to unlock

the base. Rotate the base to

the desired position, and lock

the base by turning the knob

clockwise. Calibrated degree

markings on the base of the

ballhead mark the position of

the camera precisely.

4.Calibrated Base

5.Dual-LockingQuick-Release

6.Mount Quick-ReleasePlate

OPERATION

Visit our website at ObenSupports.com

for more Oben products.

!Warnings:

• Do not exceed the ballhead’s maximum

load capacity (see packaging for details).

• Ensure that all appropriate locks are

engaged when necessary.

• Ballhead should only be used in

temperatures ranging between -22° and

140° F (-30° and 60° C). Do not operate in

saltwater. Dry ballhead if it becomes wet.

• Remove the camera from the ballhead

during setup or transport.

• Keep out of reach of children.

After mounting the quick-release

plate to your camera, ensure that

the locking knob on the ballhead

is securely tightened. To mount

the camera to the ballhead, ﬁrst

insert the side of the Quick-

Release Plate that is opposite the

quick-release latch. Then, press

down on the side of the quick-

release plate nearest the quick-

release latch. The quick-release

latch will automatically lock into

place when the plate is pushed

into the groove.

Warning: Always use one hand to

secure the camera while adjusting

the ballhead, and ensure that the

lock is engaged before letting go of

the camera.

OPERATION

7.Mount Camera

www.obensupports.com

Allother trademarksarethe propertyoftheir respectiveowners

GG3

Indice

Manuali Accessori per fotocamere popolari di altre marche

Viltrox

Viltrox EF-NEX Istruzioni per l'installazione

Calumet

Calumet 7100 Series CK7114 Manuale utente

Ropox

Ropox 4Single Series Manuale utente

Cambo

Cambo Wide DS Digital Series Istruzioni operative

Samsung

Samsung SHG-120 Manuale utente

Ryobi

Ryobi BPL-1820 Manuale operativo

Aegis

Aegis ABL-36020P Manuale utente

Pentax

Pentax Data Back Fc Manuale utente

Fantasea

Fantasea EyeGrabber F Series Manuale utente

Honeywell

Honeywell HDZ20HD Manuale utente

EGO

EGO BA1400T Manuale utente

Sima

Sima SRW-62 Manuale utente

Shape

Shape A7SSMKIT Manuale utente

Slide Kamera

Slide Kamera HST-2 Manuale utente

Power works

Power works 2902613 Manuale utente

SES

SES SE-2047-2 Manuale utente

Olympus

Olympus PT-EP05L Manuale utente

Starlite

Starlite OctoDome nxt Manuale utente