Ocean Blue 400950 Guida all'installazione

SAVE THESE INSTRUCTIONS

DEALER/INSTALLER: GIVE TO HOMEOWNER

Ocean Blue

Outside Safety Ladder

Assembly and Installation Manual

Part no. 400950

Use with 30”/38”

Ocean Blue Mighty Step

to make a complete pool

entrance system.

Outside Safety Ladder

alone cannot be used to

enter/exit swimming pool.

Not for Use

with Soft

Sided Pools

- 1 -

Ocean Blue Outside Safety Ladder

Use with 30”/38”Ocean Blue Mighty Step

ASSEMBLY INSTRUCTIONS - PLEASE READ BEFORE ATTEMPTING ASSEMBLY

Tools Needed for Assembly

■Rubber Mallet

■Cordless Drill w/Phillips

Driver

■5/16” Drill Bit

■Pencil

Parts List

■2 - Side Rails

■2 - Handrails

■2 - Return Handrails

■2 - Mounting Blocks Rails

■2 - Mounting Blocks

■1 - Platform

■1 - Right Adjustable Rail Boot

■1 - Left Adjustable Rail Boot

■2 - Swing up Rails

■3 - Swing up Treads

■1 - Bottom Swing-up Tread

■1 - Fixed Ladder Tread

■1 - Hardware Safety Pack

Hardware Bag

■10 - 1/4-20 hex nuts

■20 - 1/4 -#10 x3/4 Phillips

self-tapping screws

■4 - 1/4-20 x 1.5”

■4 - 1/4-20 x .625”

■2 - 1/4 - 20 x 3-1/2” Bolts

■2 - 1/4” Flat Washers

■Instructions

■Padlock

2 – Handrails

2 – Swing-

up Rails

1 - Platform

1 - Fixed Ladder

Tread

2 - Right

Adjustable

Rail Boots

1 - Bottom

Swing-Up Tread

3 - Swing-up

Treads

1 - Hardware/Safety Pack

2 - Left Adjustable

Rail Boots

2 - Side Rails

2 – Return

Handrails

2 - Mounting

Blocks

2 - Mounting

Block Rails

- 2 -

Tools Needed: Rubber Mallet

Step #1

#1: Lay out the Swing-up

Rails and Swing-up Treads as

shown.

NOTE: The bottom Swing-up

Tread has a“house shaped”

tab and is positioned at the

bottom of the Swing-up Rail.

#3: Place the remaining Swing-up

Rail over the tabs of the Swing-up

Treads and tap into place using the

rubber mallet. Set this assembly

aside.

#1: Slip one of the Adjustable Rail

Boots over the end of a Side Rail.

It will need to be all the way on

if the outside dimension of your

pool is 50” or

backed off to

the marked

number that

corresponds

with the height

of your pool.

#2: Using two 1/4-20 x 1 1/2” long

bolts and two 1/4-20 hex nuts,

fasten the Adjustable Rail Boot to

the Side Rail. Repeat for remaining

Side Rail.

Step #3 continued

Step #2

Tools Needed: Rubber Mallet, cordless drill with Phillips bit.

#2: Using a rubber mallet, tap the

Swing-up Treads into place.

Adjustable Rail Boots are not required if the outside height of your pool

(measured from the ground to the top of the pool ledge) is 48”or less. If

this measurement is more than 48”rail boots will be required. If the out-

side measurement of your pool is 48” or less, skip to step 3.

#1: Overlap the at end of the

Handrail onto the top of the Side

Rail. Using two 1/4 - 20 x 5/8” bolts

and two 1/4- 20 hex nuts, attach the

Handrail to the Side Rail. Repeat for

the remaining Side Rail.

Step #3

Tools Needed: Rubber Mallet, cord-

less drill with Phillips bit.

- 3 -

Step #3 continued

#2: Slide two Handrails up through

the bottom of the Platform using the

openings nearest to the tabs.

#3: Stand up the assembly and us-

ing a rubber mallet tap the Platform

down until seated on the lugs on

the Side Rails. IT MAY REQUIRE

SEVERAL HARD BLOWS WITH A

RUBBER MALLET TO SEAT THE

PLATFORM ALL THE WAY DOWN

ONTO LUGS.

#4: Laying the

assembly on its

side, insert the

Return Hand-

rails through the

bottom of the

remaining holes

in the Platform

until seated on the lugs.

#5: Using two #10 x 3/4” self-tap-

ping screws, connect the Handrails

together by using one screw on

the outside and one screw on the

inside. Repeat for the remaining

handrails.

#6: Using the rubber mallet, attach

the xed ladder tread to the bottom

of the ladder as shown. NOTE: The

small groove should face the inside

of the ladder.

- 4 -

Step #4

#2: Using the rubber mallet, tap

the Mounting Blocks onto the

Mounting Block Rails.

#3: Slide the Mounting Block as-

semblies up into the open end of

the Return Handrails as shown.

Ladder is now ready to attach to

Ocean Blue Mighty Step.

Step #5

Tools Needed: Rubber Mallet, cordless drill with Phillips bit and a pencil.

Step #5 continued

Tools Needed: Rubber Mallet,

cordless drill with Phillips bit.

#1: Flex the oval openings on the

Swing Ladder assembly over the

two round tabs on the Platform.

Using a rubber mallet tap down on

the Swing-up Rail until seated over

the round tab.

Attaching Outside Safety Ladder to your

Ocean Blue Mighty Step

CHOOSE A LOCATION THAT IS LEVEL AND IN FULL VIEW.

POOL MUST HAVE COMPETENT ADULT SUPERVISION AT ALL TIMES WHEN IN USE.

Step #5

#1: Place your ladder over the

pool wall and rest the Mounting

Blocks on the pool step. The ladder

Platform must be level and rest on

top of the swimming pool ledge for

support. Depending on the outside

height of swimming pool ledge, rail

boots may

need to be

readjusted at

this time.

#2: Position the ladder so the

Mounting Blocks sit at. Using

a pencil, mark the height on the

Mounting Block Tubes. NOTE: If

necessary you may need to cut

down the Mounting Block Rails

with a hacksaw.

#3: Laying the ladder on its side,

attach both Mounting Block

assemblies to the ladder using two

#10 x 3/4” self-tapping screws in

each assembly.

#5: Check to make sure the hole

locations in the Platform are clear

of pool wall and supports. Drill two

5/16 holes through the Platform

and pool ledge. Fasten the ladder

platform to the pool ledge using two

¼-20 x 2-1/4” bolts, ¼-20 hex nuts.

OUTSIDE TREADS MUST

BE IN THE UP POSITION

AND LOCKED AT ALL

TIMES WHEN POOL IS

NOT IN USE.

- 5 -

Step #5 continued

#4: Position the ladder over the pool step with the Mounting Blocks sitting at on the top tread. Center the

ladder side-to-side and align the back of the Mounting Blocks next to the groove in the back of the Platform as

shown. Attach using four #10 x 3/4” self-tapping screws in each Mounting Block.

#6: When the pool is not in use,

rotate the Swing-up Ladder to the

up position and secure it in place

with the padlock as shown.

- 6 -

IMPORTANT For Your Safety

■Check the contents of the carton with the parts list for this ladder.

■DO NOT attempt to assemble or install the ladder if there are

ANY shortages of parts or hardware.

■For proper assembly and installation follow all instructions in the

sequence shown.

■Before using the product, after assembly and installation, go

over the instructions and procedures again to make sure nothing

has been overlooked.

■Be sure and safe. The manufacturer IS NOT responsible for

improper assembly, installation and use.

To keep your new ladder working properly, just hose off once a

week with clean water. Check the Swing-Up portion of the Outside

Safety ladder for proper operation. Check padlock for proper

operation, lubricate if necessary.

MAINTENANCE:

Unfasten the ladder from the pool ledge and from the Ocean Blue

Mighty Step. Store in a safe place out of the elements.

WINTERIZING:

Safety Rules

■Locate ladder on a solid base.

■One person on the ladder at

a time.

■Ladder MUST be installed per

manufacturer’s instructions.

■Secure ladder to top rail of

pool for greater stability and

safety as outlined in this

assembly manual.

■DANGER: No Jumping or

Diving from ladder.

■Face ladder when entering

and leaving pool.

■To prevent entrapment or

drowning — DO NOT swim

through, behind or around

ladder.

■Ladder to be used as a

swimming pool ladder only.

■Weight limit -

300 lbs. maximum

■Warning: Exceeding the

maximum weight restriction

may cause the ladder to fail.

■When ladder is not in use,

slide up outside ladder

section and lock using

padlock. Ladder must be

locked at all times when not in

use or when there is no

qualied adult supervision.

■Consult your local Building

Department before installation

of your pool and equipment.

■DANGER: Use a cordless

drill for assembly and

installation. NEVER use an

electric drill in or around the

pool.

OCEAN BLUE WATER PRODUCTS WARRANTY

Ocean Blue Water Products warrants their swimming pool ladders to be free from defects in

workmanship for one year from date of purchase.

DO NOT RETURN DEFECTIVE PART TO DEALER

The defective part should be returned, post paid, to:

Ocean Blue Water Products

7447A S Central Ave

Bedford Park IL 60638

Enclose proof of purchase (receipts, etc.) showing date purchased, your name, address, and

daytime phone number. You will be notied of cost to replace part. This warranty gives you specic

legal rights, and you may also have other rights which may vary from state to state.

Made in U.S.A • Printed in U.S.A.

- 7 -

Not for Use with Soft Sided Pools

Indice

Altri manuali Ocean Blue Attrezzatura di illuminazione

Ocean Blue

Ocean Blue 400200 Guida all'installazione

Manuali Attrezzatura di illuminazione popolari di altre marche

Brizo

Brizo 8SP-MU-4 Manuale utente

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuale utente

IKEA

IKEA BJÖRKSPIREA Manuale utente

Laserworld

Laserworld Evolution Series ES-400RGB Manuale utente

Alien

Alien RG STAR Manuale utente

EuroLite

EuroLite LED B-40 Manuale utente

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuale utente

Commercial Electric

Commercial Electric 54568141 Manuale utente

CREE LIGHTING

CREE LIGHTING 304 Series Manuale utente

Goobay

Goobay 49867 Manuale utente

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuale utente

Alkalite

Alkalite Krypton KT-81 Manuale utente

Clas Ohlson

Clas Ohlson GU10 Manuale utente

DTS

DTS DELTA 10 F Manuale utente

ring

ring Solar Steplight Manuale utente

One Stop Gardens

One Stop Gardens 57696 Istruzioni per il montaggio

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuale utente

SIREM

SIREM Swimeo A2 Manuale utente