Octave TouchTunes Manuale utente
About This Guide
This setup guide is intended for TouchTunes Digital Jukebox Operators, as well as TouchTunes field service,
customer support, and sales personnel.
Topics
•What is TouchTunes Wireless Broadband?
•TouchTunes Wireless Broadband Hardware Kit Contents
•Setting up TouchTunes Wireless Broadband
•Troubleshooting
•Contacting Technical Support
What is TouchTunes Wireless Broadband?
Wireless Broadband enables TouchTunes operators to connect their jukeboxes to the Internet using a high-
speed wireless connection. All OpenStage jukeboxes require a high-speed Internet connection.
NOTE Make sure your jukebox has the latest software version installed before proceeding with the
installation of the Wireless Broadband connection. If the jukebox is not currently connected to a
broadband connection, you can update its software by taking out the hard drive and placing it in
another jukebox that does have a broadband connection, performing the software update, and
then putting the hard drive back in its original jukebox. The minimum required software version is
OpenStage 2.20.3-4.
TouchTunes Wireless Broadband Velocity
Installation Guide
July 2019
901118-001
Rev 00
2 Wireless Broadband Velocity Installation Guide
TouchTunes Wireless Broadband Hardware Kit Contents
TouchTunes Wireless Broadband Hardware Kit Contents
The TouchTunes Wireless Broadband Velocity hardware kit (600309-001) contains the following components
(note that the SIM card will already be installed in the modem and is shown outside of it for illustrative purposes
only).
Figure 1 TouchTunes Wireless Broadband AT&T Velocity Hardware Kit
3Wireless Broadband Velocity Installation Guide
Setting up TouchTunes Wireless Broadband
Setting up TouchTunes Wireless Broadband
Setting up your Wireless Internet connection consists of two steps:
•Step 1 - Verifying the SIM card is pre-installed in the USB Modem
•Step 2 - Installing and Configuring the Wireless USB Modem
Step 1 - Verifying the SIM card is pre-installed in the USB Modem
1. Open the USB modem by removing the cover as shown in the following figure.
Figure 2 Opening the USB modem
Item Description Quantity Part No.
Nano Sim Card, 4G LTE, Velocity 1 700804-001
Modem, 4G LTE AT&T Velocity 1 700787-002
Per, 4G LTE Blade Antenna, Pano, W18" Cable TouchTunes
Wireless
1 700739-002
USB Cable Extension, 6" 1 300398-006
Broadband AT&T Velocity Installation Guide (this document) 1 901118-001
4 Wireless Broadband Velocity Installation Guide
Setting up TouchTunes Wireless Broadband
2. The SIM slot already contains the SIM card, which was removed from the larger card included with the kit.
Figure 3 Verifying the SIM card is pre-installed
3. There is a serial number printed on the small SIM that also appears below a bar code on the larger card. Copy
this serial number somewhere you can easily find it again in the future. You may need it when calling technical
support about this jukebox’s wireless broadband connection. You can also keep the bigger card for the same
purpose.
4. Connect the antenna to the other end of the antenna cable by pushing the smaller connector into the big one,
carefully aligning the central pin from the big connector so it goes into the small hole on the small connector.
5Wireless Broadband Velocity Installation Guide
Setting up TouchTunes Wireless Broadband
Once the connectors are pushed in together as far as they can go, fasten the two together using the screw
part on the smaller connector.
Figure 4 Connecting the antenna cable
5. For best operation, position the antenna outside of the jukebox.
Step 2 - Installing and Configuring the Wireless USB Modem
To install and configure your wireless modem:
1. Remove any existing telephone line connections or previous USB wireless modems from the jukebox
computer.
6 Wireless Broadband Velocity Installation Guide
Setting up TouchTunes Wireless Broadband
2. Press your jukebox’s Manager (MNGR) button to enter Manager mode. The Manager button is located on the
I/O Board on Virtuo, Angelina, and Fusion jukeboxes. The button is located on the backplane for Playdium
jukeboxes.
Figure 5 Pressing the Manager button on the jukebox
7Wireless Broadband Velocity Installation Guide
Setting up TouchTunes Wireless Broadband
3. At the Operator menu, press DIAGNOSTIC.
Figure 6 Selecting Diagnostic
8 Wireless Broadband Velocity Installation Guide
Setting up TouchTunes Wireless Broadband
4. Under CONNECTION TYPE, press the Configure button.
Figure 7 Selecting Configure
9Wireless Broadband Velocity Installation Guide
Setting up TouchTunes Wireless Broadband
5. Under CONNECT WITH, press Broadband, and then under the HOST CONFIGURATION area, press
Wireless.
Figure 8 Selecting Broadband, then Wireless
10 Wireless Broadband Velocity Installation Guide
Setting up TouchTunes Wireless Broadband
6. Return to the Diagnostic - Network Status screen by pressing the Diagnostic button.
Figure 9 Returning to the Diagnostic - Network Status screen
7. Flip open the USB plug on the wireless modem and insert it into your jukebox’s appropriate USB port. For
Angelina/Fusion computers, you can plug the modem into any free USB port. For Playdium and Virtuo, you
must use a specific port. See Figure 11 for which ports to use. Also, for Playdium, Angelina and Fusion
jukeboxes, the included USB extension cable is required to prevent damage to the modem.
Figure 10 Flip the USB connector and plugging into a Virtuo directly, or into a Playdium using a USB cable extension
Altri manuali per TouchTunes
1
Indice
Altri manuali Octave Juke-box
