OEM Tools 24669 Manuale di servizio

UNPACKING

After unpacking unit, inspect carefully for any damage

that may have occurred during transit. Check for loose,

missing, or damaged parts. If any damage is observed,

a shipping damage claim must be ﬁled with carrier. Do

not use the OEMTOOLS™Drill if broken, bent, cracked, or

damaged parts (including labels) are noted. Any Drill that

appears damaged in any way, operates abnormally, or is

missing parts should be removed from service immediately.

If you suspect that the Drill was subjected to shock load

(a load that was dropped suddenly, unexpectedly, etc.),

immediately discontinue use until it has been checked by

a factory authorized service center.

Please read and save these instructions. Read through this owner’s manual carefully before using product. Protect yourself and

others by observing all safety information, warnings, and cautions. Failure to comply with instructions could result in personal

injury and/or damage to product or property. Please retain instructions for future reference.

The following safety information is provided as a guideline to help you operate your Drill under the safest possible conditions.

Any tool or piece of equipment can be potentially dangerous to use when safety or safe handling instructions are not known or

not followed. The following safety instructions are to provide the user with the information necessary for safe use and operation.

Please read and retain these instructions for the continued safe use of your service system. Failure to follow instructions listed

below may result in serious injury. In addition, make certain that anyone who uses the equipment understands and follows

these safety instructions as well.

Operating Instructions and Parts Manual 24669

FOR CUSTOMER SERVICE

Technical Question?

CALL 1-866-458-2472

[email protected]

Thank you very much for choosing an OEMTOOLS™Product!

For future reference, please register your new tool at www.oem-tools.com and complete the owner’s record below:

Model: _______________ Purchase Date: ___________

Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product

before you begin using it. This product is designed for certain applications only. OEMTOOLS™cannot be responsible for issues

arising from modiﬁcation. We strongly recommend this product is not modiﬁed and/or used for any application other than that for

which it was designed. If you have any questions relative to a particular application, DO NOT use the product until you have ﬁrst

contacted customer service to determine if it can or should be performed on the product.

Explanation of Safety Signal Words

WARNING:Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION:Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

CAUTION:Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may

result in property damage.

NOTES:Provide clarity and helpful information.

3/8"DRILL

4/18

2018 OEMTOOLS™

WARNING

Operating Instructions and Parts Manual 24669

4/18

2018 OEMTOOLS™

3/8"DRILL

POWER TOOL SAFETY

WARNING:Read all safety warnings and instructions.

Failure to follow the warnings and instructions may result

in electric shock, ﬁre and/or serious injury.

Save all warnings and instructions for future reference.

WORK AREA SAFETY

Keep work area clean and well lit. Cluttered or dark areas

invite accidents.

DO NOT operate power tools in explosive

atmospheres, such as in the presence of ﬂammable

liquids, gases or dust. Power tools create sparks which

may ignite the dust or fumes.

Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

1. Power tool plugs must match the outlet. Never modify

the plug in any way. DO NOT use any adapter plugs

with earthed (grounded) power tools. Unmodiﬁed plugs

and matching outlets will reduce risk of electric shock.

2. Avoid body contact with earthed or grounded surfaces

such as pipes, radiators, ranges and refrigerators. There

is an increased risk of electric shock if your body is

earthed or grounded.

3. DO NOT expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

4. DO NOT abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of

electric shock.

5. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of

electric shock.

6. If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of a ground fault circuit

interrupter (GFCI) reduces the risk of electric shock.

PERSONAL SAFETY

1. Stay alert, watch what you are doing, and use common

sense when operating a power tool. DO NOT use a

power tool while you are tired or under the inﬂuence of

drugs, alcohol, or medication. A moment of inattention

while operating power tools may result in serious

personal injury.

2. Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will

reduce personal injuries.

3. Prevent unintentional starting. Ensure the switch is in

the OFF position before connecting to power source

and/or battery pack, picking up, or carrying the tool.

Carrying power tools with your ﬁnger on the switch

or energizing power tools that have the switch ON

invites accidents.

4. Remove any adjusting key or wrench before turning

the power tool ON. A wrench or a key left attached

to a rotating part of the power tool may result in

personal injury.

5. DO NOT overreach. Keep proper footing and balance

at all times. This enables better control of the power

tool in unexpected situations.

6. Dress properly. DO NOT wear loose clothing or jewelry.

Keep your hair, clothing and gloves away from moving

parts. Loose clothes, jewelry or long hair can be caught

in moving parts.

7. If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-related hazards.

POWER TOOL USE AND CARE

1. DO NOT force the power tool. Use the correct power

tool for your application. The correct power tool will

do the job better and safer at the rate for which it was

designed.

2. DO NOT use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

3. Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk

of starting the power tool accidentally.

4. Store idle power tools out of the reach of children and

DO NOT allow persons unfamiliar with the power tool

or these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

5. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

6. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

7. Use the power tool, accessories and tool bits, etc. in

accordance with these instructions, taking into account

the working conditions and the work to be performed.

Use of the power tool for operations different from

those intended could result in a hazardous situation.

8. Hold power tools by insulated gripping surfaces when

performing an operation where the cutting tool may

contact hidden wiring or its own cord. Contact with a

“live” wire will make exposed metal parts of the tool

“live” and shock the operator.

SERVICE

Have your power tool serviced by a qualiﬁed repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

Operating Instructions and Parts Manual 24669

4/18

2018 OEMTOOLS™

3/8"DRILL

WARNING:Know your drill. DO NOT plug in the

drill until you have read and understand this Instruction

Manual. Learn the tool’s applications and limitations, as

well as the speciﬁc potential hazards related to this tool.

Following this rule will reduce the risk of electric shock,

ﬁre, or serious injury.

WARNING:Always wear eye protection. Any power

tool can throw foreign objects into your eyes and cause

permanent eye damage. ALWAYS wear safety goggles

(not glasses) that comply with ANSI safety standard

Z87.1. Everyday glasses have only impact resistant

lenses. They ARE NOT safety glasses.

WARNING:Glasses or goggles not in compliance with

ANSI Z87.1 could cause serious injury when they break.

WARNING:Always use a safety shield, hearing

protection, and dust mask when drilling concrete.

1. DO NOT drill material too small to be securely held.

2. Always keep hands out of the path of the drill bit. Avoid

awkward hand positions where a sudden slip could

cause your hand to move into the path of the drill bit.

3. Secure the workpiece. Use clamps or a vice to hold the

workpiece. It is safer than using your hand and it frees

both hands to operate the tool.

4. Make sure there are no nails or foreign objects in the

part of the workpiece to be drilled.

5. To avoid injury from accidental starting, always remove

the plug from the power source before installing or

removing a drill bit.

6. DO NOT install or use any drill bit that exceeds 7" (17.5

cm) in length or extends more than 6"(15 cm) beyond

the chuck jaws. They can bend or break suddenly.

7. Before starting the operation, jog the drill switch to

make sure the drill bit does not wobble or vibrate.

8. DO NOT use ﬂy cutters or multiple-part hole cutters,

because they can come apart or become unbalanced

during use.

9. Make sure the spindle has come to a complete stop

before touching the chuck or attempting to change the

drill bit.

10. Always make sure the chuck is tight and the drill bit

ﬁrmly tightened in the chuck before starting drill.

GUIDELINES FOR EXTENSION CORDS

Make sure your extension cord is the proper size.

When using an extension cord, be sure to use one

heavy enough to carry the current the tool will draw.

An undersized cord will cause a drop in line voltage

resulting in loss of power and overheating. The table at

right shows the correct size to use according to cord

length and nameplate ampere rating. If in doubt, use

the next heavier gauge. The smaller the gauge number,

the heavier the cord.

Be sure your extension cord is properly wired and in

good condition. Always replace a damaged extension

cord or have it repaired by a qualiﬁed electrician before

using it. Protect your extension cord from sharp objects,

excessive heat and damp or wet areas.

Use a separate electrical circuit for your power tools.

This circuit must not be less than 14 gauge wire and

should be protected with either a 15A time delay fuse

or circuit breaker. Before connecting the power tool

to the power source, make sure the switch is in the

OFF position and the power source is the same as

indicated on the nameplate. Running at lower voltage

will damage the motor.

WARNING:Repair or replace damaged or worn

extension cords immediately.

Select the appropriate extension cord gauge and length

using the chart below.

When operating a power tool outdoors, use an outdoor

extension cord marked “W-A” or “W”. These cords are rated

for outdoor use and reduce the risk of electric shock.

WARNING:Keep the extension cord clear of the

working area. Position the cord so it will not get caught

on the workpiece, tools, or any other obstructions while

you are working with the power tool.

Minimum Gauge (AWG) Extension Cords

(120 V use only)

Ampere rating Total length

than

Not

than

25'

(7.5 m)

50'

(15 m)

100'

(30 m)

150'

(45 m)

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not applicable

IMPORTANT SAFETY INSTRUCTIONS

The warnings, precautions, and instructions discussed

in this manual cannot cover all possible conditions

and situations that may occur. The operator must

understand that common sense and caution are factors

which cannot be built into this product, but must be

supplied by the operator.

DISPOSAL

At the end of the useful life of the OEMTOOLS™Drill,

dispose of the components according to all state, federal,

and local regulations.

PURPOSE

The OEMTOOLS™3/8" Drill is built with a powerful 4.0

Amp motor to power through the toughest jobs. It is

designed with an easy access forward/reverse lever for

one-hand operation and an ergonomic, rubber mold-

over grip for comfort. It is used for drilling holes, driving

screws, loosening or tightening various materials together

with fasteners and other applications.

Operating Instructions and Parts Manual 24669

4/18

2018 OEMTOOLS™

3/8"DRILL

PRODUCT SPECIFICATIONS

Motor: 4 Amp, 120V, 60Hz

Variable Speed: 0-3,000 RPM (No-load)

Chuck: 3/8" Keyless

Max. Drilling Capacity: 1" (Wood) and 3/8" (Metal)

Trigger Lock: Yes

Rocker Switch: Forward/Reverse

Cord: 6 Ft.

Weight: 3.5 Lbs.

WARNING:Double insulated tools are equipped

with a polarized plug (one blade is wider than the

other). This plug will ﬁt in a polarized plug only one

way. If the plug does not ﬁt fully in the outlet, reverse

the plug. If it still does not ﬁt, contact a qualiﬁed

electrician to install a polarized outlet. DO NOT change

the plug in any way. Double insulation eliminates the

need for the three wire grounded power cord and

grounded power supply system.

OPERATING INSTRUCTIONS

WARNING:Be sure you read, understand and apply

safety instructions before use.

1. Always inspect, maintain and operate in accordance

with ANSI safety code for power tools and other local

safety codes and regulations.

2. Use clamps or other practical ways to secure and

support the workpiece to a stable platform.

3. DO NOT force the tool. Use the correct tool for the job.

4. Disconnect the plug from the power source before

making any adjustments, changing accessories or

storing the tool.

5. Check for misalignment or binding moving parts,

breakage of parts, and any other condition that may

affect the tool’s operation. If damaged, have the tool

serviced before using.

6. Use only accessories that are recommended by the

manufacturer for your model.

7. Always make sure the work surface is free from nails

and other foreign objects.

8. Never hold the workpiece in one hand and the tool in

the other hand when in use. Never place hands near or

below the cutting surface.

9. Never lay workpiece on hard surfaces like concrete,

stone, etc.

10. Always check accessory bits, grinding stones, cut-off

wheels, etc. for damage before each use.

11. To avoid shock or ﬁre, replace power cord immediately

if it is worn, cut or damaged in any way.

12. Avoid accidental starting. Be sure switch is OFF before

plugging in.

13. Remove adjusting keys or wrenches before turning the

tool ON.

WARNING:If any part is missing or damaged, DO NOT

plug the Drill into the power source until the missing or

damaged part is replaced.

WARNING:To avoid ﬁre or toxic reaction, never use

gasoline, naphtha, acetone, lacquer thinner, or similar

highly volatile solvents to clean the tool.

ASSEMBLY AND OPERATION

FORWARD/REVERSE SWITCH

The forward/reverse switch (1) is conveniently mounted

above the trigger switch (#2 in Fig. 1). To make the drill

rotate clockwise for drilling, push the forward/reverse switch

to the right. To make the drill rotate counterclockwise, push

the forward/reverse switch to the left.

NOTES: Never change the position of the forward/

reverse switch while the chuck is turning.

There is no dead center position for the forward/reverse

switch.

The tool will run only when it is in either the full left or full

right position.



Fig. 1



VARIABLE SPEED TRIGGER SWITCH

This drill is equipped with a variable-speed ON/OFF

trigger switch.

1. To start drill, gently squeeze the trigger switch

(#2 in Fig. 2). NOTE:The drill will turn at its slowest

speed when the trigger switch is depressed slightly.

The drill will turn at its fastest speed when the trigger

switch is fully depressed.



Fig. 2



2. To stop the drill, release the trigger switch.

NOTE: Drilling at a slow speed for an extended period of

time may cause the drill motor to overheat. If drill gets hot,

stop drilling and allow it to cool for at least 15 minutes.

INSTALLING DRILL BITS

WARNING:Never hold the chuck body with one hand

and use the drill power to rotate the drill body to loosen

or tighten bits. Serious injury may result.

This drill is equipped with a keyless chuck.

This chuck is designed to provide easy two-handed

tightening and loosening of the chuck jaws.

1. To open the keyless drill chuck, grasp and hold the

chuck collar (1) with one hand (Fig. 3). Rotate the chuck

body (2) in a counterclockwise direction until the chuck

jaws (3) open wide enough to accept the bit (4).

Fig. 1

Fig. 2

Operating Instructions and Parts Manual 24669

4/18

2018 OEMTOOLS™

3/8"DRILL

2. Insert the bit into the chuck the full length of the jaws or

until the spiral portion of the bit is near the chuck jaws.

Raise the front of your drill slightly to prevent the bit

from falling out of the chuck jaws.

3. Tighten the chuck jaws onto the bit by turning the

chuck body in a clockwise direction.

NOTE: Make sure the bit is properly aligned in the jaws

and NOT at an angle. An improperly aligned bit could be

thrown from the chuck when the drill is started.

4. Finish tightening the chuck jaws by holding the chuck

collar with one hand and ﬁrmly tightening the chuck

body by rotating it in a clockwise direction.

NOTE: Hand tighten the chuck jaws. DO NOT use pliers.



Fig. 3



WARNING:DO NOT insert the drill bit into the chuck

and tighten as shown in Fig. 4. The drill bit MUST be

properly inserted with all three of the chuck jaws holding the

bit centered in the chuck. Failure to properly insert the drill

bit could cause the drill bit to be thrown from the chuck, and

could result in serious injury or damage to the chuck.



Fig. 4



REMOVING DRILL BITS

1. To open the keyless drill chuck, grasp and hold the

chuck collar with one hand. Rotate the chuck body in

a counterclockwise direction until the chuck jaws open

wide enough to release the bit.

2. Remove the bit.

TRIGGER SWITCH LOCK

The trigger switch lock-on feature allows the trigger

switch to be locked in the ON position at full speed when

continuous operation for extended periods of time is

required (Fig. 5).



Fig. 5



To lock the trigger switch in the ON position, pull back on

the trigger switch to start the drill. Continue to squeeze

the trigger until the drill reaches its maximum speed. Push

the trigger switch lock button (3) into the drill handle.

Release the trigger switch while holding the trigger switch

lock button into the drill handle. The drill will continue to

run at full speed. To release the trigger switch lock button,

pull the trigger switch back and then release the trigger.

DRILLING

When drilling into smooth, hard surfaces such as metal,

use a center punch to mark the desired hole location.

This will prevent the drill bit from slipping off center as the

hole is started.

The workpiece to be drilled should be secured in a vice or

with clamps to keep it from turning as the drill bit rotates

(Fig. 6).

Fig. 6



1. Check the drill bit to make sure it is ﬁrmly locked into

the drill chuck, and verify that the forward/reverse

switch is in the forward position.

2. Hold the drill ﬁrmly with both hands whenever possible.

Use one hand to grasp the handle and switch.

NOTE: Make sure the hand placed on the body of the

drill does not cover the air vents. Covering these air

vents will reduce motor cooling, and possibly lead to

overheating the motor.

3. While holding the drill ﬁrmly, place the point of the drill

bit at the point to be drilled.

4. Squeeze the switch trigger to start the drill.

NOTE: Always use a higher drill speed when drilling small

holes. Use a slower drill speed when drilling large holes.

5. Move the drill bit into the workpiece applying only enough

pressure to keep the bit cutting. DO NOT force the drill bit

or apply sideways pressure to elongate the hole.

WARNING:Be prepared for binding and bit breakthrough.

When these situations occur, the drill bit has a tendency to

grab the workpiece. This action will kick the drill opposite

to the direction of the drill bit rotation, and could cause loss

of control when breaking through material as you complete

drilling the hole. If you are not prepared, this loss of control

can result in serious injury.

Fig. 5

Fig. 6

Fig. 4

Fig. 3

Operating Instructions and Parts Manual 24669

4/18

2018 OEMTOOLS™

3/8"DRILL

When drilling metals, use light oil on the drill bit to keep

it from overheating. The oil will prolong the life of the drill

bit and improve the cutting action. If the bit jams in the

workpiece, or if the drill stalls, release the trigger switch

immediately. Remove the bit from the workpiece and

determine the reason for jamming.

REMOVING THE CHUCK

To remove the chuck:

1. Remove the drill plug from the power source.

2. Insert a 5/16"(8 mm) or larger hex key (1) into the chuck

(2) and tighten the chuck jaws securely (Fig. 7). Make

sure each of the chuck jaws (3) is seated on the ﬂat

surfaces of the hex key.



Fig. 7



3. Tap the hex key sharply with a mallet (4) in a clockwise

direction. This action will loosen the screw in the chuck

for easy removal.

4. Open chuck jaws and remove the hex key.

5. Open the chuck jaws as far as possible.

6. Remove the chuck screw using a #2 screwdriver

(Fig. 8)



Fig. 8



NOTE: Turn the screw CLOCKWISE to remove it.

This screw has a left-handed thread. Insert the hex

key into the chuck and tighten jaws of chuck securely

(Fig. 9). Tap the hex key sharply with a mallet in a

COUNTERCLOCKWISE direction. This will loosen the

chuck on the spindle. The chuck can now be unscrewed

and removed from the spindle by hand.

Insert the hex key into the chuck and tighten jaws of

chuck securely (Fig. 9). Tap the hex key sharply with a

mallet in a COUNTERCLOCKWISE direction. This will

loosen the chuck on the spindle. The chuck can now be

unscrewed and removed from the spindle by hand.



Fig. 9



RETIGHTENING A LOOSE CHUCK

After installing a chuck that has previously been removed,

the chuck may become loose on the spindle and develop

a wobble. Also, the chuck screw may become loose,

causing the chuck jaws to bind and prevent them from

closing. To tighten the chuck, follow these steps:

1. Insert the hex key into the chuck and tighten the chuck

securely.

2. Tap the hex key sharply with a mallet in a CLOCKWISE

direction (Fig. 10). This will tighten the chuck on the

spindle.



Fig. 10



3. Open the chuck jaws and remove the hex key.

4. Tighten the chuck screw using a #2 screwdriver.

NOTE: Turn the screw COUNTERCLOCKWISE to tighten

it. This screw has a left-handed thread.

MAINTENANCE

WARNING:When servicing, use only identical

replacement parts. The use of any other part may create a

hazard or cause product damage.

DO NOT use solvents when cleaning plastic parts.

Plastics are susceptible to damage from various types of

commercial solvents and may be damaged by their use.

Use a clean cloth to remove dirt, dust, oil, grease, etc.

WARNING:DO NOT allow brake ﬂuids, gasoline,

petroleum-based products, penetrating oils, etc. to come

into contact with plastic parts. They contain chemicals

that can damage, weaken or destroy plastic.

DO NOT abuse power tools. Abusive practices can

damage the tool and the workpiece.

WARNING:DO NOT attempt to modify tools or create

accessories. Any such alteration or modiﬁcation is misuse

and could result in a hazardous condition leading to

possible serious injury. It will also void the warranty.

LUBRICATION

All of the bearings in this tool are lubricated with a

sufﬁcient amount of high-grade lubricant for the life of

the unit under normal conditions. Therefore, no further

lubrication is required.

WARNING:When servicing, use only original

equipment replacement parts. The use of any other parts

may create a safety hazard or cause damage to the drill.

Any attempt to repair or replace electrical parts on

this drill may create a safety hazard unless repairs are

performed by a qualiﬁed technician. For more information,

call the Toll-free Helpline, at 1-866-458-2472.

Fig. 7

Fig. 8

Fig. 9

Fig. 10

Operating Instructions and Parts Manual 24669

4/18

2018 OEMTOOLS™

3/8"DRILL

PARTS DIAGRAM

PARTS LIST

This symbol designates that this tool is listed

with U.S. and Canadian requirements by ETL

Testing Laboratories, Inc. and conforms to UL

Std. 60745-1, 60745-2-1, 60745-2-2. Certiﬁed to

CAN/CSA Std. C22.2 No. 60745-1, 60745-2-1,

60745-2-2.

Item # Description Qty.

1 Chuck Screw 1

2 3/8 Chuck 1

3 Shaft 1

4 Bearing 6001-RS 1

5 Big Gear 1

6 Bearing 687-RS 1

7 Bearing Seat 1

8 Bearing 608-RS 1

9 Fan 1

10 Forward/Reverse Switch 1

11 Cord Set 1

12 Cord Guard 1

Item # Description Qty.

13 Housing 1

14 Screw 8

15 Screw 2

16 Strain Relief 1

17 Switch 1

18 Stator 1

19 Bearing 607RS 1

20 Carbon Brush 2

21 Brush Holder 2

22 Copper Crush Holder 2

23 Rotor 1

NOTE: Not all components of the Drill are replacement

items, but are illustrated as a convenient reference for

location and position in the assembly sequence.

Operating Instructions and Parts Manual 24669

4/18

2018 OEMTOOLS™

3/8"DRILL

3580 E. Raines Road, Suite 3, Memphis, TN 38118

Tel: 1-866-458-2472

www.oem-tools.com

OEMTOOLS™ONE YEAR WARRANTY

For up to one year from the date of purchase of this OEMTOOLS™product, if you ﬁnd any defect in material or

workmanship (through normal usage), return it to the place of purchase or to OEMTOOLS™for repair or replacement at

our discretion. In order to obtain this service, send the product and proof of purchase (transportation pre-paid) to:

OEMTOOLS™Q.A. Dept, 3580 E. Raines Road #3, Memphis, TN 38118.

We will not be responsible for lost or damaged goods during transportation; please insure your package. If our

inspection veriﬁes the defect, we will either repair or replace the product, or we may elect to refund the purchase price

if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if

we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you

must bear the cost of returning the product.

OEMTOOLS™does not provide warranty for products labeled other than OEM®or OEMTOOLS™. OEMTOOLS™will

not provide any warranty for products subjected to abnormal use. Abnormal use includes (but is not limited to) abuse,

accident, alteration, neglect, and unauthorized or unreasonable use or repairs. This warranty does not cover bits,

blades, ﬁles, batteries, or calibration. We recommend that you maintain your tools and sharpen or replace blades, bits,

ﬁles, and batteries as necessary. OEMTOOLS™reserves the right to make any changes in construction or design at

any time without any obligation in incorporating such changes to tools or equipment previously sold. OEMTOOLS™

makes every effort to ensure that its products meet high quality and durability standards, and warrants to the original

purchaser that this product is free from defects in materials and workmanship for the period of one year from the

date of purchase. This warranty does not apply to damage due directly or indirectly to misuse, abuse, negligence or

accidents, repairs, or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or

to lack of maintenance.

We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or

consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of

incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY

IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF

MERCHANTABILITY AND FITNESS. This warranty gives you speciﬁc legal rights, and you may also have other rights,

which vary from state to state.

Don’t forget to register your new OEMTOOLS™product at www.oem-tools.com.

Indice

Altri manuali OEM Tools Trapano

OEM Tools

OEM Tools 24660 Manuale utente

Manuali Trapano popolari di altre marche

Makita

Makita BDF456 Manuale utente

Black & Decker

Black & Decker LDX220 Manuale utente

Hitachi

Hitachi DH 40MA Manuale utente

Challenge

Challenge JO Manuale tecnico di riferimento

Makita

Makita LXFD01 Manuale utente

Festool

Festool T18+3 Manuale utente

Milwaukee

Milwaukee M12 FPDX-202X Manuale utente

EINHELL

EINHELL TE-RH 32 E Manuale utente

Makita

Makita DHP484 Manuale utente

Makita

Makita FD05 Manuale utente

Bosch

Bosch PSB 530 RA Manuale utente

Maximum

Maximum 054-1359-4 Manuale utente

Makita

Makita HP332D Manuale utente

Raider

Raider RDP-HD31H Manuale utente

Bort

Bort BPM-1400x2 Manuale utente

Black & Decker

Black & Decker 7266 Manuale utente

KENT USA

KENT USA TRD1230 Manuale utente

Bosch

Bosch GSB 19-2 RE Manuale utente