OEM Tools 24496 Manuale di servizio

UNPACKING

After unpacking unit, inspect carefully

for any damage that may have occurred

during transit. Check for loose, missing,

or damaged parts. If any damage is

observed, a shipping damage claim

must be ﬁled with carrier. Do not use the

OEMTOOLS®Polisher if broken, bent,

cracked or damaged parts (including

labels) are noted. Any Polisher that appears

damaged in any way, operates abnormally

or is missing parts should be removed

from service immediately. If you suspect

that the Polisher was subjected to shock

load (a load that was dropped suddenly,

unexpectedly, etc.) immediately discontinue

use until it has been checked by a factory

authorized service center.

Please read and save these instructions. Read through this owner’s manual carefully before using product. Protect yourself and

others by observing all safety information, warnings, and cautions. Failure to comply with instructions could result in personal

injury and/or damage to product or property. Please retain instructions for future reference.

The following safety information is provided as a guideline to help you operate your Polisher under the safest possible conditions.

Any tool or piece of equipment can be potentially dangerous to use when safety or safe handling instructions are not known or

not followed. The following safety instructions are to provide the user with the information necessary for safe use and operation.

Please read and retain these instructions for the continued safe use of your service system. Failure to follow instructions listed

below may result in serious injury. In addition, make certain that anyone who uses the equipment understands and follows

these safety instructions as well.

Operating Instructions and Parts Manual 24496

FOR CUSTOMER SERVICE

Technical Question?

CALL 1-866-458-2472

[email protected]

7" VARIABLE SPEED POLISHER

Thank you very much for choosing an OEMTOOLS®Product!

For future reference, please register your new tool at www.oem-tools.com and complete the owner’s record below:

Model: _______________ Purchase Date: ___________

Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this

product before you begin using it. This product is designed for certain applications only. OEMTOOLS®cannot be responsible

for issues arising from modiﬁcation. We strongly recommend this product is not modiﬁed and/or used for any application other

than that for which it was designed. If you have any questions relative to a particular application, DO NOT use the product until

you have ﬁrst contacted customer service to determine if it can or should be performed on the product.

WARNING: Pursuant to California Proposition 65, this product contains chemicals known to the state of California to cause

cancer and birth defects or other reproductive harm. Wash hands after handling.

Explanation of Safety Signal Words

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

CAUTION: Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result

in property damage.

NOTES: Provide clarity and helpful information.

WARNING

1/17

2017 OEMTOOLS®

Operating Instructions and Parts Manual 24496

1/17

2017 OEMTOOLS®

7" VARIABLE SPEED POLISHER

POWER TOOL SAFETY

WARNING

Read and understand all safety warnings and instructions.

Failure to follow the warnings and instructions may result in

electric shock, ﬁre and/or serious injury.

Save all warnings and instructions for future reference.

WORK AREA SAFETY

1. Keep work area clean and well lit. Cluttered or dark areas

invite accidents.

2. Do not operate power tools in explosive atmospheres,

such as in the presence of ﬂammable liquids, gases or

dust. Power tools create sparks which may ignite the

dust or fumes.

3. Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

1. Double insulated tools are equipped with a polarized plug

(one blade is wider than the other). This plug will ﬁt in a

polarized plug only one way.

2. If the plug does not ﬁt fully into the outlet, reverse the plug.

If it still does not ﬁt, contact a qualiﬁed electrician to install

a polarized outlet. Do not alter the plug in any way. Double

insulation eliminates the need for the three-prong grounded

power cord and grounded power supply system.

3. Avoid body contact with grounded surfaces such as

pipes, radiators, ranges and refrigerators. There is

increased risk of electric shock if your body is grounded.

4. Do not expose power tools to rain or wet conditions.

Water entering the power tool will increase the risk of

electric shock.

5. Do not abuse the cord. Never use the cord to carry the

tool or pull the plug from an outlet. Keep cord away from

heat, oil, sharp edges or moving parts. Replace damaged

cords immediately. Damaged cords increase the risk of

electric shock.

6. When operating a power tool outdoors, use an outdoor

extension cord marked “W-A” or “W”. These cords are rated

for outdoor use and reduce the risk of electric shock.

7. When not in use, disconnect from the power source and

store in a safe, dry childproof location.

8. Avoid body contact with grounded surfaces such as

pipes, radiators, ranges and refrigerators.

PERSONAL SAFETY

1. Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a power tool

while you are tired or under the inﬂuence of drugs, alcohol

or medication. A moment of inattention while operating

power tools may result in serious personal injury.

2. Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask, non-

skid safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

3. Prevent unintentional starting. Ensure the switch is in the

off-position before connecting to power source and/or battery

pack, picking up or carrying the tool. Carrying power

tools with your ﬁnger on the switch or energizing power

tools that have the switch on invites accidents.

4. Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached

to a rotating part of the power tool may result in

personal injury.

5. Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

6. Dress properly. Do not wear loose clothing or jewelry.

Keep your hair, clothing and gloves away from moving

parts. Loose clothes, jewelry or long hair can be caught in

moving parts.

7. If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can

reduce dust related hazards.

POWER TOOL SAFETY

1. Do not force the power tool. Use the correct power tool

for your application. The correct power tool will do the job

better and safer at the rate for which it was designed.

2. Do not use the power tool if the switch does not turn it on

and off. Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

3. Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

4. Store idle power tools out of the reach of children and do

not allow persons unfamiliar with the power tool or these

instructions to operate the power tool. Power tools are

dangerous in the hands of untrained users.

5. Maintain power tools. Check for misalignment or binding

of moving parts, breakage of parts and any other

condition that may affect the power tool’s operation. If

damaged, have the power tool repaired before use. Many

accidents are caused by poorly maintained power tools.

6. Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to

bind and are easier to control.

7. Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into account

the working conditions and the work to be performed.

Use of the power tool for operations different from those

intended could result in a hazardous situation.

8. Hold the power tool by insulated gripping surfaces when

performing an operation where the cutting tool may

contact hidden wiring or its own cord. Contact with a

“live” wire will make exposed metal parts of the tool “live”

and shock the operator.

9. Use clamps or other practical ways to secure and support

the workpiece to a stable platform. Holding the workpiece

by hand or against your body leaves it unstable and may

lead to loss of control.

Operating Instructions and Parts Manual 24496

1/17

2017 OEMTOOLS®

7” VARIABLE SPEED POLISHER

SERVICE

Have your power tool serviced by a qualiﬁed repair person

using only identical replacement parts. This will ensure that

the safety of the power tool is maintained.

SPECIFIC SAFETY RULES

WARNING

1. Know your polisher. Carefully read and understand this

Instruction Manual. Learn the tool’s applications and

limitations, as well as the speciﬁc potential hazards

related to this tool. Following this rule will reduce the risk

of electric shock, ﬁre, or serious injury.

2. Always wear eye protection. Any power tool

can throw foreign objects into your eyes and cause

permanent eye damage. ALWAYS wear safety goggles

(not glasses) that comply with ANSI safety standard

Z87.1. Everyday glasses have only impact resistant

lenses. They ARE NOT safety glasses.

3. Glasses or goggles not in compliance with ANSI Z87.1

could cause serious injury when they break.

4. Always wear gloves to protect your hands from hot sparks.

5. Always wear hearing protection and a dust mask. Use

only in well ventilated areas. Use of personal protective

equipment and working in a safe environment will reduce

the risk of injury.

6. Accessories must be rated for at least the speed

recommended on the tool warning label. Wheels and

other accessories running over rated speed can ﬂy apart

and cause injury.

7. Hold tool by insulated gripping surfaces when

performing an operation where the cutting tool may

contact hidden wiring or its own cord. Contact with a

“live” wire will make exposed metal parts of the tool

“live” and shock the operator.

8. When an extension cable is required, you must ensure it

has the right ampere rating for your power tool and is in a

safe electrical condition.

9. Always switch off before you put the tool down.

10. If possible, always use clamps or a vise to hold your work.

11.Rags, cloths, cord, string and the like should never be left

around the work area.

12.If you are interrupted when operating the tool, complete

the process and switch off before looking up.

13.Periodically check that all nuts, bolts and other ﬁxings are

properly tightened.

14.Always use both hands to operate the tool.

15.Do not force the tool, let the tool do the work at a

reasonable speed. Overloading will occur if too much

pressure is applied and the motor slows resulting in

inefﬁcient operation and possible damage to the motor.

16.Do not continue to use worn, torn or heavily clogged

sanding discs.

17.Do not touch the moving disc.

18.Ensure that you have removed foreign objects such

as nails and screws from the work piece before

commencing sanding.

EXTENSION CORD SAFETY

WARNING

Keep the extension cord clear of the working area.

Position the cord so it will not get caught on the

workpiece, tools or any other obstructions while you are

working with the power tool.

1. Make sure any extension cord used with this tool is in

good condition. When using an extension cord, be sure

to use one of heavy enough gauge to carry the current

the tool will draw. An undersized cord will cause a drop in

line voltage resulting in loss of power and overheating.

2. The table below shows the correct size to use according

to cord length and nameplate ampere rating. If in doubt,

use the next heavier gauge. The smaller the gauge

number the heavier the cord.

3. Be sure your extension cord is properly wired and in

good condition. Always replace a damaged extension

cord or have it repaired by a qualiﬁed electrician before

using it. Protect your extension cord from sharp objects,

excessive heat and damp or wet areas.

4. Use a separate electrical circuit for your power tools.

This circuit must not be less than 14 gauge wire and

should be protected with either a 15 A time delayed

fuse or circuit breaker. Before connecting the power

tool to the power source, make sure the switch is in

the OFF position and the power source is the same as

indicated on the nameplate. Running at lower voltage

will damage the motor.

MINIMUM GAUGE (AWG) EXTENSION

CORDS (120 V use only)

Amperage

rating

Total length

than

Not

than

25'

(7.5 m)

50'

(15 m)

100'

(30 m)

150'

(45 m)

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Applicable

Operating Instructions and Parts Manual 24496

1/17

2017 OEMTOOLS®

7" VARIABLE SPEED POLISHER

IMPORTANT SAFETY INSTRUCTIONS

The warnings, precautions, and instructions discussed in this

manual cannot cover all possible conditions and situations

that may occur. The operator must understand that common

sense and caution are factors which cannot be built into this

product, but must be supplied by the operator.

WARNING

Use only attachments recommended or sold by

manufacturer.

1. Do not disassemble the polisher. Take it to a qualiﬁed

professional when service or repair is required. Incorrect

reassembly may result in electric shock or ﬁre.

2. Only use accessories which are speciﬁcally designed for

use with a 7" variable speed polisher.

3. Wear approved safety eye/face shield, ear defenders and

hand protection.

TROUBLESHOOTING

DISPOSAL

At the end of the useful life of the OEMTOOLS®7" Variable

Speed Polisher, dispose of the components according to all

state, federal and local regulations.

PURPOSE

Whether you are a professional detailer, or a weekend

DIY guy, the OEMTOOLS®Variable Speed Sander/

Polisher is up to the task. Featuring a soft start, this

sander/polisher comes equipped with a variable speed

dial that makes it easy to maintain the right speed to

avoid swirl marks and overheating the surface. RPM

range can be adjusted as low as 1,000 RPM all the

way up to 3,000 RPM. Plus, it has a common 5/8" x 11

spindle so you can attach a variety of accessories.

PRODUCT SPECIFICATIONS

Motor: 11 Amp

No-Load Speed: 1,000 – 3,000 RPM

Spindle Thread: 5/8" x 11

Spindle Lock: Yes

Electronic Speed Control: Yes

Variable Speed Control Dial: Yes

Power Cord Length: 6 Ft.

Weight: 8 Lbs.

INSTRUCTIONS

SETTING UP

D-HANDLE GRIP

Using the included Screws and Hex Key

Wrench, attached the D-Handle to the

Gear Housing as shown. The D-Handle

can be installed for either right-hand or

left-hand use.

OPERATION

VARIABLE SPEED

1. The polisher is ﬁtted with a variable

speed dial that allows the speed to be

adjusted to suit the application and

material.

2. The tool operates between the speeds

of 1,000 RPM and 3,000 RPM.

3. The higher the number on the variable

speed dial, the higher the speed.

4. For polishing and bufﬁng applications it is recommended

that a lower speed (1,000-1,500 RPM) is used.

5. For sanding applications it is recommended that the

high speed (3,000 RPM) is used to provide efﬁcient

material removal.

Trouble Problem Suggested Remedy

Sander/polisher

will not start

Power cord not

plugged in

Ensure that the cord is

connected to the power

supply

Power fault, fuse or

circuit breaker tripped

Check the power supply

Cord damaged Use authorized service

center to repair or replace

Faulty switch Use authorized service

center to repair or replace

switch

Faulty motor Use authorized service

center to repair or replace

motor

Poor performance Extension cord too long

or undersized

Use extension cord heavy

enough to carry the current

Tool is overheating Turn off the tool and let

it cool down to room

temperature. Inspect and

clean the ventilation slots

Too much wax on the

polishing sponge

Replace or clean the

accessory. Ensure that too

much polish is not applied

onto the accessory. Remove

a portion of wax and retry

Polishing bonnet or

bufﬁng wheel worn

Replace with new bonnet or

bufﬁng wheel

Vibration or

abnormal noise

Accessory not secured Ensure that the accessory is

secured onto the spindle and

that all ﬂanges are tight

Loose screws Ensure that all ﬁxing screws

are fully tightened

Operating Instructions and Parts Manual 24496

1/17

2017 OEMTOOLS®

7” VARIABLE SPEED POLISHER

WARNING

Do not operate the machine with a polishing bonnet attached

above 1,500 RPM.

ON/OFF

1. Before starting the sander/polisher, ﬁrst

ensure the accessory and the tool are in

good condition. Plug the cord set into

the outet and set up for the application

to be performed.

2. Hold the tool ﬁrmly.

3. Press the lock-off button and then

press the on/off switch.

4. To adjust the speed, rotate the variable

speed dial.

5. To turn the tool off, release the on/off

switch.

6. The sander/polisher will stop.

NOTE: The disc continues to turn for a few

seconds even though the switch is turned off.

7. Keep hands well away from the moving disc.

8. DO NOT place the sander/polisher down until the disc

has come to a complete stop.

ATTACHING THE BACKING PAD

Switch off the tool and disconnect it from

the power source.

1. To ﬁt the backing pad onto the spindle

press and hold the spindle lock button

and screw the backing pad onto the

spindle in a clockwise direction. Turn

the pad by hand, ensuring that it is tight

on the spindle and that it rotates fully

and does not wobble unduly.

2. To remove the backing pad, press and hold the spindle

lock button and unscrew the pad from the spindle.

NOTE: The pad unscrews in a counterclockwise direction.

3. Run the sander/polisher at no load for at least one minute

to ensure the new sanding pad is in good condition.

Make sure you are wearing all the safety gear and that

you face the sander/polisher away from you.

FITTING THE SANDPAPER

1. The sander/polisher is ﬁtted with a

hook and loop backing pad allowing

easy changing of accessories. Ensure

there are no debris left in the hooks

and loops of the pad before ﬁtting

accessories.

2. Align the sandpaper with the backing

pad and press down ﬁrmly to ensure a

good grip.

3. Special care must be taken with hook and loop pads,

as a build-up of dust, or wearing the sandpaper down

completely before changing it, can result in damage to

the hooks and loops on the pad and require a new pad to

be ﬁtted.

NOTE: Hook and loop pads, backing pads, bonnet, foam

pad and wool pad are not covered under the warranty.

SELECTING THE RIGHT GRADE OF

SANDPAPER

Switch off the tool and disconnect it from the power supply.

1. Different grades of sandpaper can be purchased from

your local hardware store.

2. Typical grades are coarse (40–60 grit), medium (80–100

grit), and ﬁne (120–240 grit).

3. Use coarse grade to remove rough ﬁnishes, medium

grade to smooth the work, and ﬁne grade to ﬁnish it off.

4. It is best to make a trial run on a scrap piece of material

to determine the optimum grades of sandpaper for a

particular job.

HOLDING AND GUIDING THE TOOL

1. Always clamp the work piece where

applicable.

2. Before starting the tool, ﬁrst ensure the

sanding pad, sanding disc and the tool

are in good condition. Plug the cord

into the mains socket.

3. To start the tool squeeze the on/off

trigger.

4. Do not overload the tool so that the disc slows down. Let

the tool do the work rather than applying pressure. The

weight of the tool alone provides sufﬁcient pressure.

5. Hold the tool securely and make sure that you have full

control at all times.

6. During the sanding operation, maintain an angle of

10–15 degrees between the tool and the work piece. After

completing the application, turn the sander/polisher off. To

turn the tool off let go of the on/off switch. The tool will stop.

NOTE: The disc continues to spin for a few seconds even

though the switch is turned off.

7. Keep hands well away from the moving disc.

PREPARING THE SURFACE

NOTE: For optimum results, ensure that the surface is clean

and dry before polishing. Most high-gloss surfaces can be

cleaned with a mild soap and water solution. A mild ammonia

such as that used in glass cleaners can be used to remove

stubborn dirt such as road tar, grease and bug stains.

WARNING

Always check the label for recommended applications

before using a cleaning product. Using the incorrect product

for the application may damage the surface. Use only

recommended car care products.

NOTE: Never apply cleaner directly onto the surface to be

polished. Apply to a clean cloth and then use the cloth to

clean the surface.

Operating Instructions and Parts Manual 24496

1/17

2017 OEMTOOLS®

7" VARIABLE SPEED POLISHER

ATTACHING THE BONNET

The sander/polisher is supplied with a

polishing bonnet used for ﬁne bufﬁng and

to ﬁnish the surface.

1. The polishing bonnet is ﬁtted over the

backing pad.

2. To ﬁt the backing pad turn the sander/

polisher upside down.

3. Place the backing pad onto the spindle

making sure that it ﬁts securely.

4. Fit the polishing bonnet over the top

of the backing pad and ensure that the

outer edge is drawn over the top of the

backing pad.

5. Turn the sander/polisher over. Run

the sander/polisher at no load for at least one minute to

ensure the backing pad and polishing bonnet are in good

condition. Make sure you are wearing all the safety gear

and that you face the sander/polisher away from you.

ATTACHING POLISHING PAD OR FOAM PAD

1. Attach hook and loop foam or wool pad to backing pad,

being careful to center the backing pad with the foam or

wool pad.

2. Screw backing pad onto spindle while depressing spindle

lock button.

3. Turn the sander/polisher over. Run the sander/polisher at

no load for at least one minute to ensure the wool or foam

pad is in good condition.

4. Make sure you are wearing all the safety gear and that

you face the sander polisher away from you.

POLISHING

1. Ensure the variable speed dial is set to the slowest speed.

2. Hold the sander/polisher ﬁrmly against the surface and

squeeze the on/off trigger.

3. Always start and stop the sander/polisher on or against

the surface being buffed.

4. Begin by bufﬁng larger ﬂat surfaces, such as hood, trunk and

roof. Use a broad sweeping motion in a crisscross pattern.

5. Do not press down on the surface with the sander/polisher.

Do not overload the tool so that the disc slows down. Let

the tool do the work rather than applying pressure. The

weight of the tool alone provides sufﬁcient pressure.

6. Once ﬂat surfaces have been covered, buff curved

surfaces such as car doors and quarter panels. Use small

circular motions.

7. After bufﬁng the entire surface turn the tool off and let go

of the on/off switch. The tool will stop.

NOTE: The disc continues to spin for a few seconds even

though the switch is turned off. Keep hands well away from

the moving disc.

8. Wait until the pad stops rotating before lifting the sander/

polisher from the surface.

9. Unplug the sander/polisher.

10.Buff surfaces by hand for hard to reach areas, such as

the underside of bumpers or side mirrors.

MAINTENANCE

WARNING

Always ensure that the tool is switched off and the plug

is removed from the power point before making any

adjustments or maintenance procedures.

1. Avoid using solvents when cleaning plastic parts, most

plastics are susceptible to damage from various types of

commercial solvents and may be damaged by their use.

2. Use clean cloth to remove dirt and carbon dust.

3. Do not at any time allow brake ﬂuids, gasoline, petroleum

based products or penetrating oils to come into contact

with plastic parts. They contain chemicals that can

damage, weaken or destroy plastic.

4. Allow the pad to dry completely after each use.

5. Be careful not to use too much polish at one time, if the

sponge becomes saturated it will not last as long.

WARNING

Turn the on/off switch to the off position and unplug the

tool from the power supply before performing trouble

shooting procedures.

CLEANING

1. Keep the tool’s air vents unclogged and clean at all times.

2. Remove dust and dirt regularly. Cleaning is best done with a rag.

3. Never use caustic agents to clean plastic parts.

CAUTION

Do not use cleaning agents to clean the plastic parts of the

tool. A mild detergent on a damp cloth is recommended.

Water must never come into contact with the tool.

GENERAL INSPECTION

Regularly check that all the ﬁxing screws are tight. They may

vibrate loose over time.

ELECTRICAL WARNING

POWER SOURCE CONNECTION POWER

REQUIREMENTS

This product is designed to operate on a properly grounded

120 volt, 60Hz, single-phase alternating current (AC) power

source fused with a time delayed fuse or circuit breaker. It is

recommended that a qualiﬁed electrician verify the ACTUAL

VOLTAGE at the receptacle into which the product will be

plugged and conﬁrm that the receptacle is properly fused

and grounded.

DO NOT OPERATE THIS PRODUCT if the ACTUAL power

source voltage is less than 105 Volts AC or greater than 132

Volts AC. Contact a qualiﬁed electrician if this problem exists.

Improper performance and/or damage to the product will result

if operated on inadequate or excessive power.

DO NOT abuse cord. Never use the cord to carry tools or pull

the plug from an outlet. Keep cord away from heat, sharp

edges or moving parts. Replace damaged cords immediately.

Damaged cords increase the risk of electric shock.

compounds or plaster. During any use on these materials it

is extremely important that the tool is cleaned frequently by

blowing it out with an air jet.

Operating Instructions and Parts Manual 24496

1/17

2017 OEMTOOLS®

7” VARIABLE SPEED POLISHER

Figure Description Qty.

Backing Pad 1

B Woodruff Key 1

C Output Spindle 1

D Card 1

E Screw 4

F Front Cover 1

G Bearing 1

H Bearing Cover 1

I Screw 3

J Big Gear 1

K Circlip for Shaft 2

L Needle Bearing 1

M Screw 4

N Gear Housing 1

O E Ring 1

P Spring 1

Figure Description Qty.

Q Brake Pin 1

R Bearing 1

S Bearing Cover 1

T Screw 3

U Armature 1

V Bearing 1

W Rubber Brush 1

X Fan Guide 1

Y Screw 2

Z Stator 1

AA Screw 2

BB Up-Carbon Cap 1

CC Carbon Brush 2

DD Brush Holder 2

EE Spring 2

FF Plastic Housing 1

Figure Description Qty.

GG Name Plate 2

HH Down-Carbon Cap 1

II Switch 1

JJ Speed Control 1

KK Back Housing 1

LL Screw 5

MM Terry Bonnet 1

NN Cord Clip 1

OO Screw 2

PP Back Housing 1

QQ Rubber Sleeve 1

RR Cord 1

SS Side Handle 1

TT Screw 1

UU Screw 1

VV Screw 4

WW Hex Key 10 mm 1

PARTS LIST

This symbol designates that this tool

is listed with U.S. requirements by ETL

Testing Laboratories, Inc. Conforms to UL

Std. 60745-1 and 60745-2-3.

Intertek

5006077

ZZ6850

PARTS DIAGRAM

NOTE: Not all components of the Polisher are replacement items,

but are illustrated as a convenient reference for location and position

in the assembly sequence.

Includes (1) wool pad, (1) foam piece and (1) sandpaper not shown.

C US

Operating Instructions and Parts Manual 24496

1/17

2017 OEMTOOLS®

7" VARIABLE SPEED POLISHER

OEMTOOLS®ONE YEAR WARRANTY

If for up to one year from the date of purchase of this OEMTOOLS®product you ﬁnd any defect in material

or workmanship, through normal usage, return it to the place of purchase, or to OEMTOOLS®for repair

or replacement at our discretion. In order to obtain this service, send your tool and proof of purchase,

transportation pre-paid, to OEMTOOLS®Q.A. Dept., 3580 E. Raines Road #3, Memphis, TN 38118. We will not

be responsible for lost or damaged goods during transportation; please insure your package. If our inspection

veriﬁes the defect, we will either repair or replace the product at our election, or we may elect to refund the

purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products

at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the

scope of our warranty, then you must bear the cost of returning the product.

OEMTOOLS®does not provide warranty for products labeled other than OEM®or OEMTOOLS®. OEMTOOLS®

will not provide any warranty for products subjected to abnormal use. Abnormal use includes, but is not limited

to, abuse, accident, alteration, neglect, and unauthorized or unreasonable use or repairs. This warranty does not

cover bits, blades, ﬁles, batteries, or calibration. We recommend that you maintain your tools and sharpen or

replace blades, bits, ﬁles, and batteries as necessary. OEMTOOLS®reserves the right to makes any changes in

construction or design at any time without any obligation in incorporating such changes to tools or equipment

previously sold.

OEMTOOLS®makes every effort to ensure that its products meet high quality and durability standards, and

warrants to the original purchaser that this product is free from defects in materials and workmanship for the

period of one year from the date of purchase. This warranty does not apply to damage due directly or indirectly

to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper

installation, normal wear and tear or to lack of maintenance.

We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or

consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation

of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS

WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE

WARRANTIES OF MERCHANTABILITY AND FITNESS. This warranty gives you speciﬁc legal rights, and you may

also have other rights, which vary from state to state.

3580 E. Raines Road, Suite 3, Memphis, TN 38118

Tel: 1-866-458-2472

www.oem-tools.com

Don’t forget to register your new OEMTOOLS

product at www.oem-tools.com.

Indice

Altri manuali OEM Tools Levigatrice

OEM Tools

OEM Tools 24417 Manuale di servizio

Manuali Levigatrice popolari di altre marche

Oliver

Oliver 6305 Manuale utente

Jet

Jet 22-44 Pro-3 Manuale di servizio

Makita

Makita M9204 Manuale

Makita

Makita M9204 Manuale utente

Craftsman

Craftsman 351.215131 Manuale utente

Clarke

Clarke Woodworker CBS1-5B Manuale di istruzioni

Chicago Pneumatic

Chicago Pneumatic CP9778 Manuale utente

Nitto Kohki

Nitto Kohki BB-20 Manuale utente

Ferm

Ferm FEOS-135 Manuale utente

Unior

Unior 1510 Manuale utente

stayer

stayer ls1200 Manuale utente

Jet

Jet JSG-96 Manuale di servizio

Parkside

Parkside PDS 290 B2 Manuale utente

Status

Status XPA Series Manuale utente

Clarke

Clarke EZ Sand Manuale utente

Craftsman

Craftsman 113.22521 Manuale utente

Craftsman

Craftsman 113.225831 Manuale utente

CLAS

CLAS OP 1429 Manuale utente