OHAUS Defender 3000 Series Manuale utente

DEFENDER 3000 Series Floor Scale

Instruction Manual

DEFENDER 3000 Series Floor Scale EN-1

INTRODUCTION

This manual contains installation, operation and maintenance instructions for the DEFENDER 3000 Series Floor

Scale.

SAFETY PRECAUTIONS

Please follow these safety precautions:

Never operate in hazardous areas.

The foundation at the installation site must be capable of safely supporting the weight of the

floor scale plus the weight of the maximum load.

Ensure that vibrations due to machines near the installation site are kept to a minimum. This

applies also when the floor scale is integrated into conveying systems.

INSTALLATION

CAUTION: THE FLOOR SCALE IS VERY HEAVY.

ALWAYS USE AN APPROPRIATE HOIST TO LIFT IT FROM THE PACKAGING

OR TO MOVE IT INTO THE REQUIRED POSITION.

Unpacking

1. Remove the outer packaging

materials from the top and sides

of the floor scale.

2. Install the two included eye bolts

into holes in top of platform.

(See Figure 1.)

3. Lift the floor scale from the

packaging material, see caution

notice.

EYE BOLT

LOAD CELL FEET

SHIPPING FEET (IF INSTALLED)

Figure 1. Hoisting Method.

EN-2 DEFENDER 3000 Series Floor Scale

Positioning

Ensure the surface is flat in the area where the scale will be positioned, especially in the region of the load cell feet.

Small differences in height can be compensated by adjusting the load cell feet.

1. If an Indicator is included with the floor scale, ensure that it is kept with the floor scale during positioning as

there may be an attached connecting cable.

2. With the floor scale positioned over the final work area, remove the 4 shipping feet (if installed).

3. Install the 4 load cell feet (if not already installed).

4. Lower the scale on to the final work area.

5. Check that the floor scale is level; check that the 4 feet are in contact with the floor; make adjustments by

rotating the nuts on the load cell feet. Use an external level.

6. Ensure that the floor scale’s output cable does not become trapped or crushed during lifting or positioning.

Connecting an Indicator

When connecting the base to TD52 indicator, push the base connector onto the indicator connector and turn the

locking ring clockwise to lock it in place.

When connecting the base to an indicator that does not have the matching connector, install the optional load cell

cable adapter (P/N 30429931 sold separately) to the indicator. Then attach the load cell cable to the cable adapter.

Note: As an alternate wiring method, cut off the connector, strip the wires and attach them to the indicator using the

wiring codes in Table 1.

The extension cable accessory (P/N: 30429931) cannot be used if the scale will be used in a legal for trade or

legally controlled application, because there is no provision to seal the connection between the indicator and

platform.

TABLE 1. FLOOR SCALE WIRING COLOR CODE

Indicator Signal Name

Floor Scale Wire Color

EXE+

Green

SEN+

Blue

SIG+

White

SIG–

Red

SEN–

Yellow

EXE–

Black

DEFENDER 3000 Series Floor Scale EN-3

OPERATION

For setup, calibration and proper operation, refer to the instruction manual supplied with the indicator. Refer to the

specifications section of the floor scale for capacity, and readability information.

For continued best operating performance:

Avoid falling loads, shocks and hard lateral impacts

When weighing, all items should be centrally located on the floor scale and not

over hanging the sides or the ramps.

Verify the calibration of the floor scale system at regular intervals.

Operating Limits

Although the floor scales have extremely rugged construction, certain load limits must not be exceeded. Depending

on the type of loading, the maximum safe static load, i.e. the maximum admissible loading, is shown in Table 2.

TABLE 2. MAX ADMISSIBLE LOADING

Model

Maximum Central Load 1

(80% Surface Area)

Maximum side Load 2

(30% Surface Area)

One Side corner load 3

(10% Surface Area)

i-DF3000B1LAU

3800 kg

1800 kg

1200 kg

i-DF3000C1LAU

3800 kg

1800 kg

1200 kg

EN-4 DEFENDER 3000 Series Floor Scale

MAINTENANCE

Daily Checks

Check that the rocker feet are properly seated in the holes of each load cell.

Check that the 4 feet are in contact with the floor.

Check that the scale is free from debris, especially under the edges of the scale.

Check that there is no damage to the connecting cable.

Cleaning

Risk of Electrical Shock

Disconnect the power source before cleaning the scale with any liquids.

Maintenance of the floor scale is limited to regular cleaning.

–Wipe surfaces with a damp cloth.

–Use only common household cleaning agents.

–Never use water spray or high pressure cleaners.

When using optional Ramps or Foot Plates:

–Keep the air gap at the edge of the Floor Scale free of debris.

TECHNICAL DATA

Specifications TABLE 3. FLOOR SCALE SPECIFICATIONS

Floor Scale Models

i-DF3000B1LAU

i-DF3000C1LAU

Dimensions (mm)

1,200 x 1,200 x 110

Capacity (kg)

3000

Operating tempera-ture/ Humidity

–10°to 40°/ 0% to 95% Relative Humidity, Non-condensing

Emin (kg)

Material

Painted carbon steel, black painted, treaded

surface, fixed top plate 5 mm thick

Stainless steel, treaded surface, fixed top plate 5 mm

thick

Platform net wt (kg)

122

Feet

4 x swivel design, screw-in, carbon steel with rubber bottom cap, adjustable height

Load Cell Model / Material

4 x OIML C3, IP67 alloy steel, shear beam

4 x OIML C3, IP67 stainless steel, shear beam

Load Cell Capacity Emax (kg)

1,500

Load Cell Safe Overload Limit

150% of Emax

Load Cell Output Impedance

350 Ω ± 1 Ω

Load Cell Excitation Voltage

5V ~ 15V, DC/AC

Junction Box

Top access, IP65, Stainless steel, with 5m long cable

DEFENDER 3000 Series Floor Scale EN-5

DRAWINGS

Figure 2. Floor Scale Dimensions, (Shown with optional Foot Plates)

TABLE 4. FLOOR SCALE DIMENSIONS

MODELS

DIMENSIONS(mm)

FLOOR SCALE PLATFORM

FOOT CENTERS

i-DF3000B1LAU

1200

110

1100

i-DF3000C1LAU

ACCESSORIES

TABLE 5. LIST OF ACCESSORIES

ITEM

PART NUMBER

Foot Plate Kit, Painted steel, DF-B

72225239

Ramp Kit, Painted steel, 1.2m, DF-B

80252724

Pit Frame Kit, Painted steel, 1.2m, DF-B

83033710

Foot Plate Kit Stainless steel DF-C

30555522

Ramp Kit Stainless steel 1.2m DF-C

30555523

Pit Frame Kit Stainless steel 1.2m DF-C

30555524

EN-6 DEFENDER 3000 Series Floor Scale

DEFENDER 3000 SERIES FLOOR SCALE,

Installation of Optional Foot Plates and Ramps

Plates are required for certifiable installations. Installation of each Ramp also requires the installation of one set of

Foot Plates. Foot Plates are available separately and are included with the Ramp accessory kit. Refer to Figure 3

for mounting of the Foot Plates and Ramps. Installation of Floor Plates and Ramps must be done before final

placement of the Floor Scale.

Figure 3. Optional Foot Plate and Ramp Installation

Notes: 1. Expanding bolts require 12.5mm diameter holes drilled 60mm deep into the floor surface.

2. Foot Plate center to center dimensions W and L are shown in Table 6.

3. The Floor Scale must be positioned so the load cell feet rest within the large holes of the Foot Plates.

4. Ensure that a free air gap exists between the sides of the Floor Scale and the edges of the Ramps.

TABLE 6. DIMENSIONS FOR FLOOR PLATE AND RAMP INSTALLATION

MODELS

DIMENSIONS (mm)

RAMP

FOOT PLATE CENTERS

i-DF3000B1LAU

1200

1100

i-DF3000C1LAU

DEFENDER 3000 Series Floor Scale EN-7

DEFENDER 3000 SERIES FLOOR SCALE,

Installation and Dimensions of Pit Frame

SCALE

PIT FRAME

Figure 4. Pit Frame Installation

TABLE 7. DIMENSIONS OF PIT FRAME

SCALE MODEL

MATCHED PIT

FRAME MODEL

DIMENSIONS(mm)

i-DF3000B1LAU

Pit Frame 1.2m

1210

1340

i-DF3000C1LAU

EN-8 DEFENDER 3000 Series Floor Scale

COMPLIANCE

This product complies with the applicable EU Directives. The EU Declaration of Conformity is

available online at www.ohaus.com/ce.

This product complies with the EU Directive 2012/19/EU (WEEE). Please dispose of this product in

accordance with local regulations at the collecting point specified for electrical and electronic

equipment.

For disposal instructions in Europe, refer to www.ohaus.com/weee.

ISO 9001 Registration

The management system governing the production of this product is ISO 9001 certified.

LIMITED WARRANTY

Ohaus products are warranted against defects in materials and workmanship from the date of delivery through the

duration of the warranty period. During the warranty period Ohaus will repair, or, at its option, replace any

component(s) that proves to be defective at no charge, provided that the product is returned, freight prepaid, to

Ohaus.

This warranty does not apply if the product has been damaged by accident or misuse, exposed to radioactive or

corrosive materials, has foreign material penetrating to the inside of the product, or as a result of service or

modification by other than Ohaus. In lieu of a properly returned warranty registration card, the warranty period shall

begin on the date of shipment to the authorized dealer. No other express or implied warranty is given by Ohaus

Corporation. Ohaus Corporation shall not be liable for any consequential damages.

As warranty legislation differs from state to state and country to country, please contact Ohaus or your local Ohaus

dealer for further details.

Altri manuali per Defender 3000 Series

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali OHAUS Scala

OHAUS

OHAUS Scout SKX Series Manuale utente

OHAUS

OHAUS EX124 Manuale utente

OHAUS

OHAUS Traveler Series Manuale utente

OHAUS

OHAUS Valor V31X Manuale utente

OHAUS

OHAUS Adventurer Pro Series Manuale utente

OHAUS

OHAUS DEFENDER D60ER Manuale utente

OHAUS

OHAUS Scout SKX Manuale operativo

OHAUS

OHAUS T51P Manuale utente

OHAUS

OHAUS Catapult 1000 Manuale utente

OHAUS

OHAUS HP-120 Manuale utente

OHAUS

OHAUS Ranger 4000 Count Series Manuale utente

OHAUS

OHAUS Defender 3000 Series Manuale utente

OHAUS

OHAUS Ranger Manuale utente

OHAUS

OHAUS ES series Manuale utente

OHAUS

OHAUS VF Series Manuale utente

OHAUS

OHAUS DEFENDER SERIES Manuale utente

OHAUS

OHAUS ES series Manuale utente

OHAUS

OHAUS EX224 Manuale utente

OHAUS

OHAUS Defender D30BR Manuale utente

OHAUS

OHAUS Adventurer series Manuale utente

OHAUS

OHAUS Defender 6000 Indicators Manuale utente

OHAUS

OHAUS CL Series Manuale utente

OHAUS

OHAUS Adventurer Pro Series Manuale utente

OHAUS

OHAUS Ranger RC Manuale utente

Manuali Scala popolari di altre marche

AWS

AWS ZEO-50 Manuale utente

Gima

Gima Glass Body Fat Analyzer Manuale elenco delle parti

Seca

Seca 374 Manuale utente

TEC

TEC TEC SL59 SERIES Manuale utente

Axis

Axis B/E Series Manuale utente

Alecto

Alecto ACW-40 Manuale utente

Rice Lake

Rice Lake MSI-4260 IS Manuale utente

IKA

IKA RCT basic safety control Manuale utente

ADE

ADE M20011 Manuale utente

Duronic

Duronic KS3000 Manuale utente

Digi

Digi SM-720 Manuale utente

Cardinal

Cardinal CS Series Manuale utente

Korona

Korona Kastella Manuale utente

A&D

A&D FC-50Ki Manuale utente

BDA

BDA CAMARGUE Manuale utente

Tanita

Tanita HD-357 Manuale utente

Leifheit

Leifheit 03173 Manuale utente

Lumme

Lumme LU-1340 Manuale utente