Olarm PRO IDS X Series Manuale utente
www.olarm.co/start
IDS X-Series Installation Guide
E & OE. Terms & conditions may apply. Page 1
2021-08-19
Locate your alarm panel
Note that the alarm panel is not the keypad. Alarm panels are
typically installed in a hidden location in the home such as a
cupboard or basement.
STEP 1
Verify the alarm panel’s rmware
version
Olarm PRO only supports IDS X-Series alarm panels with
rmware with version 2.5 and up. An alarm installer should be
able to upgrade the alarm panel rmware if required. Please
see the end of this manual for tips on how to view the alarm
panel rmware version via the keypad.
STEP 2
Unbox your Olarm PRO
The Olarm PRO box includes the following:
• 1x Olarm PRO device
• 1x Connector cable
• 1x Drill hole template and LED colour legend
• 2x Screws and wall plugs
STEP 3
Download the Olarm mobile app &
register your device
Scan QR code, or navigate to your app store on your device
and search for ‘Olarm’. This Olarm PRO will require an active
subscription to function. Please contact your installer or speak
STEP 4
Power down the alarm panel
Turn the power to your IDS X-Series alarm panel off at the
mains and disconnect the battery.
STEP 5
Connect to the X-Series adaptor board to
the alarm panel
Connect the Olarm IDS X-Series adapter board to the IDS
X-Series alarm panel as indicated below. Wire the red 12V wire
from the Olarm IDS X-Series adapter board into one of the
AUX+ terminals on the alarm panel as illustrated below.
STEP 7
Colour
White
Flashing green
Flashing blue
Blue
Red
Orange
Yellow
Purple
Status
Booting up
Connecting to alarm panel
Connecting to cloud
Connected, all okay
Cannot connect to alarm panel
Cannot connect to cloud
WiFi pairing active
Firmware upgrading - do not
power the device off
Check your Olarm PRO’s status
STEP 9
Turn the alarm panel back on
Power your IDS X-Series alarm panel on again. The Olarm PRO
should light up as per the chart below.
STEP 8
Connect the serial cable
Connect the 4-pin side of the supplied
cable to the Universal port on the Olarm
PRO. Connect the 5-pin side of the
supplied cable to an Olarm PRO IDS
X-Series adapter board. These adapter
boards are sold separately to the Olarm
PRO and can be purchased directly from
Olarm.
STEP 6
www.olarm.co/start
IDS X-Series Installation Guide
E & OE. Terms & conditions may apply. Page 2
2021-08-19
1. Ensure that the alarm system is powered up and on.
2. Ensure the alarm is disarmed.
3. Press [#] to clear the keypad.
4. Enter the installer menu by typing the installer code
followed by a [*].
a. The default installer code is [9999] or [999999].
b. If these do not work, please contact the alarm
installer who installed / manages the alarm system.
5. From the installer menu, enter the code [196] followed by
[*].
9. The Olarm PRO should turn a solid blue colour within 2
minutes and you should then be able to control the Olarm PRO
from the olarm mobile app.
6. Enter the serial security code [123456] followed by [*].
7. Press [#] button 2 to 3 times until you hear 4 to 5 beeps
from the keypad, this will take you out of the installer menu.
8. The keypad will then display:
Do NOT enter the Master Code at this stage, instead press [*]
which will then display the rmware version.
Congure the alarm panel
This section will guide you through entering a series of
codes / settings to allow the alarm panel and Olarm PRO to
communicate. The IDS X-Series alarm system caters for a
range of keypads and they all work slightly different. Please
follow the instructions relating to your keypad.
STEP 10
Please do NOT mount the Olarm PRO inside the alarm
box or near any other radio equipment. This will reduce
the signal strength and result in your device not
functioning correctly.
Mount the Olarm PRO
Mount your device using the screws and drill template
provided. We suggest mounting the Olarm PRO device on a
wall or on the outside of the alarm panel.
STEP 11
Troubleshooting
If your device LED remains ashing green for more
than 3 minutes - please check the connection between
the Olarm PRO and the alarm panel.
If your device LED is red - please check the
connection between the Olarm PRO and the alarm
panel.
If your device LED is orange - please ensure that the
Olarm PRO is located in an area with good mobile signal
strength. If it is not, please ensure that your device is
connected to WiFi using the wizard inside the Olarm
app.
If your device LED is not coming on - please check
the connection between the Olarm PRO and the alarm
panel and that the alarm panel is connected to power.
If your device LED remains purple for more than 15
minutes - please contact Olarm Support: +27 21 009 0911
To check your alarm panel rmware
version
Hold down the [*] key on the keypad down for 3 seconds. You
should see the following display:
TIP
Altri manuali Olarm Sistema di sicurezza
Manuali Sistema di sicurezza popolari di altre marche
EDM
EDM Solution 6+6 Wireless-AE Manuale utente
Highway Safety Group
Highway Safety Group EA401 Manuale utente
Siren
Siren LED GSM Manuale utente
Detection Systems
Detection Systems 7090i Istruzioni per il montaggio
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manuale utente
Siemens
Siemens FDM273 Manuale utente