Olimpia splendid Secco tech Manuale utente

TECHNICAL FEATURES

Secco Tech

Power Supply 230V - 50Hz

Input Power (27°C - 65% U.R.) 190 W – 1,2 A

Max Input Power (32°C - 80% U.R.) 232 W – 1,3A

Heating Element Input power --

Dehumidification Capacity 27°C - 65% U.R. (liters) 6,6 /24 h

Dehumidification Capacity 32°C - 80% U.R. (liters) 13 /24 h

Fan Speeds 1

Refrigerant type R 134A

Refrigerant quantity 0,160 kg

Air Flow 120 m

Tank Capacity (liters) 2

Dimensions (HxWxD) mm 300X427X258

Weight 13 kg

Noise level (sound power) 36 dB(A)

Water Proof Level IPX0

OPERATING WORKING LIMITS

Max working conditions in dehumidification mode: DB / WB 35°C/31°C

Min working conditions in dehumidification mode: DB / WB 2°C/1°C

INTRODUCTION

The dehumidifier is fitted with an electronic logic system which controls operation and optimises consumption and performance.

The keys and information on the control panel have the following meanings

1) Start / Stand-by key

2) Operating mode selection key

3) Desired humidity / increment key (selection range from 30 to 90%).

4) Desired humidity / decrement key (selection range from 30 to 90%).

5) Detected ambient humidity / temperature warning key

6) Temperature indication

7) Humidity indication

8) Operating mode indications

9) Condensate collection tank full or tank shortage (LED ON),

Continuous discharge function enabled (LED BLINKING with frequency 1.25Hz).

Tank empty/present with continuous discharge disabled (LED OFF).

SELECTING FUNCTIONS

Stand-by. Key (1)

This key activates the dehumidifier or puts it in Stand-by mode. In the latter case, the display shows ' - - - - ' and the dehumidifier is

deactivated.

Mode. Key (2)

Pressing this button the following operating modes can be set:

• DEHUMIDIFICATION, indicated by the "drop" symbol light on the display.

• DRYING

indicated by the "T-Shirt" + “HI” symbols light on the display.

OPERATION WITH CONTINUOUS DISCHARGE

To operate the dehumidifier with continuous discharge, carry out the following operations:

• Take the tank out of the appliance.

• Connect the rubber pipe provided in the outfit to the condensate collection tank (at the top of the tank compartment).

• Secure the pipe with the metal clamp provided.

• Simultaneously press the increment (3) and decrement (4) keys for three seconds, with the machine in function

The activation of this function is indicated by the flashing "tank" symbol (9).

The continuous discharge function is cancelled if the empty tank is refitted.

FUNCTION DETAILS

• DEHUMIDIFICATION indicated by the "drop" symbol light on the display.

Compressor and fan are switched on if the minimum OFF time (Cf) has elapsed and if the relative humidity

value is higher than the set point + 3; compressor and fan remain ON as long as the relative humidity value is

above the set point – 3; when below the set point – 3, compressor and fan switch off (the fan switch-off is

delayed by 30 seconds with respect to the compressor) and remain off for a minimum time equal to Cf (measured as from switch-

off of the compressor), at the end of which compressor and fan are switched back on again if the relative humidity value is greater

than the set point +3.

The set point can be adjusted from 30% to 90% Rh in steps of 5%; pressing the UP (Key 3) or DOWN (Key 4) keys increases or

decreases the set point value by 5%.

•

DRYING MODE

Compressor and fan are switched on if the minimum OFF time (Cf) has elapsed.

Compressor and fan switch off only in the following cases:

cut in of the tank full switch,

operation in defrosting mode,

alarms (the switching off of fan always delays for 30 seconds compared with compressor.

The fan speed is always the minimum speed (winding no. 1 is energized).

• DEFROSTING MODE

If there is a frost condition (evaporator temperature < Ft and compressor ON) the compressor remains on for

a maximum time equal to Co minutes, at the expiry of which air defrosting takes place (fan on at minimum

speed, resistor not active in models with resistor, compressor off) which terminates when the pre-set

temperature is reached (evaporator temperature > St), compatibly with the minimum compressor OFF

duration Cf.

If the formation of frost is detected and the compressor is stopped due to reaching of the set point before the

expiry of Co the fan remains on until the end of defrosting temperature is reached.

ALARM CODES

Display

Indication Likely Cause Suggested Solution

Relative humidity drops below very low values (<22%). Activate the dehumidifier with

higher ambient

humidity conditions.

"Hr" flashing

Humidity sensor broken. Change humidity sensor or

whole PCB (according to the

model).

"tE" flashing The ambient evaporator temperature sensor

is damaged. Change ambient temperature

sensor or whole PCB (according

to the model).

"Lo" flashing The ambient temperature is too low. It means that

after 30

minutes of operation in defrosting mode (compressor

stopped and fan working) the defrosting temperature does

not exceed St. Alarm reset automatically after room temp

rise up St.

Activate the dehumidifier with

higher ambient humidity

conditions.

"EE" flashing The EEPROM of the PCB is damaged. Change the PCB (for some

model models only).

Mnemonic Range scheduled Parameters set Description

Co 20 min 50 min 20 Compressor in defrosting ON time

Cf 3 min 15 min 3 Compressor minimum OFF time

Ft -9°C +9°C 1 Frost accumulation temperature

St 0°C +9°C 3 End of defrosting temperature

• AUTOTEST MODE

By pressing the keys 4+5 for 3 seconds in sequence with the unit in Stand-by, the following

sequence is started (each phase has a duration of 3 seconds):

- switch-on of all symbols of the displays

- display of the software release

- activation of the fan (max speed managed according to the model, resistor powered when provided) and

compressor, displaying the code At on digits to the right side and the evaporator probe temperature

to the left side.

The compressor remains ON continuously, independently of the set point and the tank level switch; the

pause between stop and subsequent start and the defrosting function are also excluded.

The tank level symbol is active if the tank is absent (switch open), off if the tank is present (input closed).

Pressing the key 5 the software refresh the standard display mode as room air temperature and relative humidity values.

Press the stand-by key or disconnect the power supply to quit the auto test mode.

SECCO TECH WIRING DIAGRAM

A1 - Power board

A2 - Control board

A3 - Humidity/temperature sensor board

B1 - Evaporator temperature probe

F1 - Overload protector

M1 - Compressor

M2 - Fan motor

S1 - Microswitch

Indice

Altri manuali Olimpia splendid Deumidificatore

Olimpia splendid

Olimpia splendid SeccoPur S Manuale elenco delle parti

Olimpia splendid

Olimpia splendid AQUARIA 18 Manuale elenco delle parti

Olimpia splendid

Olimpia splendid SECCASCIUTTO Manuale elenco delle parti

Olimpia splendid

Olimpia splendid Secco Prof Manuale del proprietario

Olimpia splendid

Olimpia splendid AQUARIA SILENT Guida rapida

Olimpia splendid

Olimpia splendid AQUARIA 18 P Manuale elenco delle parti

Olimpia splendid

Olimpia splendid seccoprof Manuale elenco delle parti

Olimpia splendid

Olimpia splendid Secco Manuale elenco delle parti

Olimpia splendid

Olimpia splendid SECCOPROF 30 P Manuale elenco delle parti

Olimpia splendid

Olimpia splendid AQUARIA 14P Manuale elenco delle parti

Olimpia splendid

Olimpia splendid SeccoMust Manuale elenco delle parti

Olimpia splendid

Olimpia splendid PROCOOL 16 E Scheda tecnica

Olimpia splendid

Olimpia splendid AQUARIA SLIM 12 P Manuale elenco delle parti

Olimpia splendid

Olimpia splendid SeccoReale Manuale elenco delle parti

Olimpia splendid

Olimpia splendid SECCOPROF 30 P Scheda tecnica

Olimpia splendid

Olimpia splendid Secco Asciutto EL Manuale elenco delle parti

Olimpia splendid

Olimpia splendid AQUARIA SLIM 14 P Manuale elenco delle parti

Olimpia splendid

Olimpia splendid AQUARIA 10 Guida rapida

Olimpia splendid

Olimpia splendid AQUARIA SILENT 15 P Manuale elenco delle parti

Olimpia splendid

Olimpia splendid SeccoReale Elettronico Manuale elenco delle parti

Manuali Deumidificatore popolari di altre marche

Daitsu

Daitsu CD031IU-DFA Manuale utente

Fehom

Fehom PDGT701BE Manuale utente

Hitachi

Hitachi RD-190GX Manuale utente

Westpoint

Westpoint MDF1-30AE Manuale utente

SOLIS

SOLIS easy dry compact Manuale utente

ENVIROBOSS

ENVIROBOSS EB240 Manuale utente

Sinclair

Sinclair R-9112 Manuale utente

Kenmore

Kenmore 580.54701 Manuale utente

Demargo

Demargo DM828NF Manuale utente

Altrad Lescha

Altrad Lescha LDH 600 Manuale utente

BOMANN

BOMANN LE 1150 CB Manuale utente

SPT

SPT SD-46 Manuale utente

REMKO

REMKO SLN 40 Manuale utente

Haier

Haier HD458 Manuale utente

Logik

Logik L20DHW12 Manuale utente

Frigidaire

Frigidaire FDR30S1 - 30 Pint Capacity Dehumidifier Guida rapida

Blitz

Blitz HHD Series Manuale utente

Prem-I-Air

Prem-I-Air PD14DEN Manuale utente

Olimpia splendid secco tech Manuale utente

Manuali Deumidificatore popolari di altre marche