1
2
3
4 5
A
B
A
1
1
1
1
Luminaire
Set of Pictograms
Mounting accessories
Manual
1 2
Pictogram Installation
3
Mounting Methods
22
11
A duration test can be conducted by pushing the
button steadily for 5 to 10 seconds. In order to be
performed, the mains power supply should be
connected and the battery should be fully charged.
The luminaire enters emergency mode, the CHARGE
LED is turned OFF and the BATTERY FAULT LED starts
blinking. Its duration is the stated autonomy duration
Manual Autonomy Test
Remove the diffusor and then by pressing the test
button briefly an operation test is initiated. The light
source and the emergency circuit of the device are
tested. The manual test can be conducted only if the
mains power supply and the battery are connected.
During this test period the LAMP TEST LED will blink.
The battery must have adequate charge. This test
lasts for 3 seconds.
Manual Operational Test
Two additional labels are included in the package.
one for 3 hours duration (180) and one for 8 hour
duration (480). Depending on the selected duration,
the installer must cover the default 1 hour (60)
printing with one label that has the required
duration. Please take notice of the orientation of the
label.
Technical Label Installation
The user can select one of the 3 available minimum
autonomy durations 1 hour, 3 hours and 8 hours. The
selection must be done while the luminaire is
disconnected from AC and battery supplies. The
selection is achieved through Switches 2 & 3 of DS1
as shown below.
Autonomy Duration Selection
These devices are used indoors and outdoors
o
(t -25-40 C) in places where emergency light is
needed, its suitable for freezers. Each device must be
permanently connected to mains power supply. In
normal operation the battery is charging. The light
source can be either on or off, depending on user’s
choice. In case of a mains power supply failure, the
device enters emergency mode and the illumination
LED turns on. When the mains power supply is
restored the device turns to normal operation.
6. I s not allowed to discard batteries into t i
common trash bins, they must be discarded
only in battery recycling points. Do not
incinerate.
5. In case of inactive use for a period greater than 2
months, disconnect the battery by pulling out the
battery’s connector.
4. In case of battery replacement, it must be
replaced by the same type, by the manufacturer
or a competent person.
3. The device must be connected to the mains
power supply through a circuit breaker that is
depends on the total line’s power load.
2. Always use in any case round mains cable, with a
diameter of 5-10mm (H05RN-F type 2x1mm² or
any other type, at least equal to it’s mechanical
and electrical properties). ATTENTION!! The cable
must not be deformed in any way (This
requirement is important to ensure the ΙΡ rating).
1. Operations for installation, maintainance or
testing must be done by authorized personnel
only.
ΑΤΤΕΝΤΙΟΝ!!!
When the luminaire is used without the pictograms
or the SP-1100 and you require more light output
then remove the lens that covers the LEDs.
Lens Removal
The Automatic Autonomy Test is conducted every 6
months and measures the device’s back up operation
and emergency duration. This test includes all
functions of the Manual Autonomy Test.
Automatic Autonomy Test
This test includes all the operations that are provided
in Manual Operational Test and is conducted
automatically every 15 days and lasts 3 seconds.
Automatic Operational Test
of the luminaire. If at the end of the test the autonomy
is lower than the nominal, the BATTERY FAULT LED will
lit and battery needs to be replaced. If the result of the
test is good then the luminaire enters charging mode
and the CHARGE LED starts blinking until the battery is
fully charged.
Oly luminaires can be surface mounted on walls or ceilings. For these mounted installations, special
accessories are included.
Wall
bottom
view Wall installation Ceiling installation
Ceiling
* ATTENTION!!! The below mounting methods can be done after request of the necessary
mounting accessories!!
Extra Mounting Methods *
Suspended ceiling installation
with mounting accessory
A-3018
Suspended installation with A-3018 accessory
The luminary can be installed in a suspended
ceiling.
A marking panel (SP-1100) can be installed on the luminary pointing the desired direction.
Suspended ceiling installation
with mounting accessories
and marking panel
Ceiling installation
with marking panel
General
5
6 7
7
8
8 9
NOTE!!
After finishing the installation you must power the luminaire for at least 24 hours in order to
completely charge the battery. The rated autonomy duration can be achieved after that time.
Package Contents
2
923100410_09_003 923100410_09_003 923100410_09_003
Drill one of the 5 available holes with a 16-18mm drill bit. Install the included rubber gasket and pass
through the power cables. Install the included tie (if needed) to fasten and securely the power cables.
34
1h
(default position) 3h 8h
Battery Connection
Attention!! The 6 plastic
latches (A) must be secured
(click sound). This requirement
is important to ensure the
IP65 rating. Power on the
luminary.
ON
1 2 3 4
ON
1 2 3 4
ON
1 2 3 4
6) Autonomy Duration Selection
(Read on General Informations, Page 1) 7 a) Permanent Maintained Operation
7 b) Non-Maintained Operation 7 c) Controlled Maintained Operation of the lamp
ON
1 2 3 4
11
10
Ν for neutral, L for live wire
WARNING!! Isolate the mains power supply before making the connections.
Ν for neutral, L for live wire WARNING!! Isolate the mains power supply before making the connections.
Description
Indications LED Status
BATT.
FAULT
(yellow)
LAMP
FAULT
(red)
CHARGE
(green)
Fully charged
Charging
Battery fault or
emergency mode
Operational test
Operational failed
Autonomy test
Duration fault
Note:
Permanently
ON
Blink
Indifferent
Off
N
L
Link
N
L
1
Installation Instructions
or
Switch number 4 of DS1
must be in ON position.
ON
1 2 3 4
Switch number 4 of DS1
must be in OFF position.
and
ON
1 2 3 4
Switch number 4 of DS1
must be in OFF position.
and
N
L
External
switch
1
2
1. Install the pictogram you need in the diffuser, be careful to
secure it on the 3 plastic holders.
2. Refit the diffusor with the pictogram to the luminary.
