Olympia electronics BS-409 Manuale utente

Page 1 from 3

PIR & microwave detector

for conventional alarm panels

BS-409

921409000_09_003

GUARANTEE

TYPICAL WEIGHT

EXTERNAL DIMENSIONS

CONSTRUCTION MATERIAL

RELATIVE HUMIDITY

OPERATION TEMPERATURE RANGE

PRODUCED IN ACCORDANCE WITH

DEGREES OF COVER PROTECTION

DETECTION RANGE

DETECTION ANGLE

ACTIVATION CONSUMPTION

IDLE CONSUMPTION

OPERATION VOLTAGE

TECHNICAL CHARACTERISTICS

8.2 - 16V DC

Thank you for purchasing this product of Olympia Electronics. A European manufacturer.

The BS-409 has a Wide Angle lens, fourfold infrared sensor and microwaves, with new electronic

circuits that minimize the false alarms, and avoid the alarm conditions caused by small animals.

The detector also has a bi directional temperature compensation circuit, for unvarying detection for all

the periods of the year.

In the figures bellow are showed the main detector’s parts.

Holding screw

LED

indicators

Lens

Cable entrance

Bracket

holding

screw

Corner

mount

knockout

Mounting

knockout

25.5mA DC

16.5mA DC

5-18m, adjustable

IP 40

EN 50130-4, EN 55022, EN 60950-1

2 years

-20 to 50 C

Up to 95%

ABS

115x61x37.5mm

100 gr

ACTIVATION PERIODE 2(+/- 1)sec

ACTIVATED RELAY OUTPUT N. C 28VD C 0.1A with 1 0Ω ser ies pr otection resistor ( open w hen co ver is removed)

High Quality European based Manufacturers

LED

OFF ON

LED

OFF ON

LED’s are enabled

LED’s are disabled

High sensitivity. 2 pulses for stable

environment.

Note: For long detection range set the switch

in OFF position.

PIR

OFF ON

Low sensitivity. 3 pulses for

harsh environment.

MW low range control according to the

room size with detection range for m 5 - 9 . Immunity to an animal up to 25 kg

``OR`` operation. The alarm signal

(relay activation) occurred when one

of the sensors signal (PIR & MW) is

present.

MW PET

Α/Ο

PET

Α/Ο

OFF ON OFF ON

OFF ON

PIR adjustment

Use the Potentiometer marked "PIR" to adjust the

detection sensitivity between 15% and 100%,

according to walk test in the protected area.

(Factory setting is 57%)

Rotate the potentiometer clockwise to increase

range, counter-clockwise to decrease range.

MW high range control according to the

room size with detection range for m10 - 18 .

Immunity to an animal up to 15 kg

``AND`` operation. The alarm signal

occurred only when both sensor signals

(PIR and MW) are present at the same

time.

Description of the detector adjustments

Connection terminals

indication

LED’s

Sensor

ΜW sensitivity

control

LED

PIR

PET

A/O

-12V+ TAMP EOL RELAY

PIR ALARM DOP

PIR PIR range

control

Microswitches

Microswitche’s operation

Selecting mounting location

The detector must be installed in areas that can cover the

larger area as possible. Avoid locations that can cause false

alarms. These locations are:

- Facing direct sunlight.

- Facing areas that may change temperature rapidly.

- Areas where there are air ducts or substantial airflows.

- Avoid screen, curtain that may block detection area.

- Do not install outdoors.

The detector can either be wall or corner mounted. If ceiling or

special wall mounting is required, use the optional bracket base

with the included parts (BASE-401).

Refer to bracket description. (See fig. 4)

Down and side view

Figure 3

TAMPER

switch

Page 2 from 3

SENSITIVITY CONTROL

Position the potentiometer "MW" at min-scale firstly,

then, along with walk testing, turn to mid-scale or max-

scale gradually until you get detection at the longest

distance for the required detection range.

Rotate the potentiometer clockwise to increase range,

counter-clockwise to decrease range.

921409000_09_003

Unscrew the holding screw and gently raise the front cover.

Carefully unscrew the PCB holding screw located on the PC board.

Break out the desired knockout holes for proper installation.

The circular and rectangular indentations at the bottom base are the knockout holes for wire entry.

You may also use mounting holes that are not in use for running the wiring into the detector.

For bracket mounting option - lead wire through the bracket.

Mount the detector base to the wall, corner or ceiling (For option with bracket see Fig. 4).

Reinstall the PC board by fully tightening the holding screw. Connect wire to terminal block.

Replace the cover by inserting it back in the appropriate closing pins and screw in the holding

screw.

Connections

Connect to terminal 1 (-) and 2 (+) the power supply.

Connect to the terminals 3 and 4 the wires from the zone 24Η (24 hours zone).

The 6 and 7 terminals are the detector’s alarm output. Connect to these terminals the wires of the

panel’s detection zone.

Testing the detector

Apply 12 Vdc power to the detector, wait 2 minutes to finish the detector warm up time. Conduct

testing with the protected area cleared of all people.

Remove front cover.Make sure that PIR and MW switches are in positions high sensitivity.

Make sure that LED switch is ON.

Replace the front cover.

Start walking slowly across the detection zone.

Observe that the detector's LED lights whenever motion is detected.

Allow 5 sec. between each test.

After the walk test is completed, the LED, PIR and MW switches may be changed.

NOTE: Walk tests should be conducted, at least once a year, to confirm proper operation and

coverage of the detector.

Page 3 from 3 921409000_09_003

Indice

Altri manuali olympia electronics Sensore di sicurezza

olympia electronics

olympia electronics BS-470 Manuale utente

olympia electronics

olympia electronics tuv BS-360 Manuale utente

olympia electronics

olympia electronics ZLD-34 Manuale utente

olympia electronics

olympia electronics GR-736/21L Manuale utente

olympia electronics

olympia electronics BSR-6060/A Manuale utente

olympia electronics

olympia electronics BSR-6060/A Manuale utente

olympia electronics

olympia electronics BSR-6060/A/MAR Manuale utente

olympia electronics

olympia electronics BSR-8019 Manuale utente

olympia electronics

olympia electronics BS-405/A Manuale utente

olympia electronics

olympia electronics TC100N Manuale utente

olympia electronics

olympia electronics BSR-6160 Manuale utente

olympia electronics

olympia electronics JA-80PB Manuale utente

olympia electronics

olympia electronics BSR-5036 Manuale utente

olympia electronics

olympia electronics BSR-6060/A/MAR Manuale utente

olympia electronics

olympia electronics BS- 660/A Manuale utente

olympia electronics

olympia electronics BS-536 Manuale utente

olympia electronics

olympia electronics BS-116 Manuale utente

olympia electronics

olympia electronics BSR-6057/A Manuale utente

olympia electronics

olympia electronics BS-661/A Manuale utente

olympia electronics

olympia electronics BSR-6060 Manuale utente

Manuali Sensore di sicurezza popolari di altre marche

THORLABS

THORLABS PDA10JT Manuale utente

Waeco

Waeco UV-DETECT Manuale utente

Intermatic

Intermatic IOS-DSIMF Manuale utente

urmet domus

urmet domus 1083 Manuale utente

Siemens

Siemens AZL66 Series Manuale utente

BTI

BTI Profiline Multi Finder Manuale utente

Challenger

Challenger SL01 Manuale utente

DMP Electronics

DMP Electronics 1122INT Manuale utente

Rielta

Rielta Ladoga MK-RK Manuale utente

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuale utente

Bosch

Bosch DS835 Manuale utente

DBI SALA

DBI SALA EZ Stop Manuale dell'operatore

Lamptime

Lamptime ST05C Manuale utente

Ubiquiti

Ubiquiti MFI-MSC Manuale utente

Subsite

Subsite 910R Istruzioni per l'installazione

Satel

Satel OPAL Pro Manuale utente

Aleph

Aleph XC-1XTEU Manuale utente

Pima

Pima LARIS QUAD Manuale utente

olympia electronics BS-409 Manuale utente

Manuali Sensore di sicurezza popolari di altre marche