Omega Engineering TCIC Manuale utente
TCIC User’s Manual
1
1. Main Features
2. Installation
3. TCIC-Monitor
3.1 Title
3.2 Menus
3.2.1 File
3.2.1.1 Exit
3.2.2 Setup
3.2.2.1 Card Settings
3.2.2.2 TCIC-Monitor Settings
3.2.2.3 Calibration and Defaults
3.2.2.4 Card ddress
3.2.2.5 View ll Settings (Read Only)
3.2.3 Library
3.2.3.1 Load
3.2.3.2 Save
3.2.3.3 Delete
3.3 "Outputs" Box
3.4 "Save to File" Command ('Start' or 'Stop')
3.5 Channel Boxes
3.5.1 Channel Title
3.5.2 Digital Display
3.5.3 nalog Display
3.5.4 Channel Description
3.5.5 "Show Graph" Command
3.6 Cold Junction Temperature
4. Command Set
4.1 Requesting Data
4.2 Change Output Status
4.3 Setpoint Configuration
4.4 Sample Program
4.5 Troubleshooting
5. Multi-Card System
6. USB, RS232 & RS485
7. Specifications
8. LabVIEW Sample
TCIC User’s Manual
2
1. Main Features
• Very High Speed & High Resolution.
• Supports up to 8 channels (differential inputs).
• Each channel can be set for a thermocouple reading or
for a voltage (millivolt) reading.
• Internal /D resolution: 24 bit (not all are used).
• Sampling rate: 400 Hz (50 Hz for each channel).
• Single opto-isolated output per channel which can be
used as a set-point (alarm etc.) or as a general purpose
output.
• Conversion tables are on board to enable stand-alone
operation.
• Reading is in °F, °C or mV.
• CJC (Cold Junction Compensation) built on board.
• Each channel supports the most popular families of
thermocouples (E, J, K, R, S, T) or any indefinite voltage
source in the range -500mV -> +500mV.
• USB as a standard method of communication.
• USB + RS485 and RS232 (option).
• Multiple boards may be connected via USB or the
optional RS485.
• On board high accuracy reference voltage for easy
calibration.
• No need for external power supply when used with USB.
• Includes Windows software for initial setup and also a
Smart data logger package for monitoring & collecting
readings in high speed – with graphic mode display.
Communication
Two types of drivers are available:
• The direct driver provides access via a DLL supplying
functions to directly control the device.
• The VCP (Virtual COM Port) driver would make the TCIC
appear as a spare COM port on the PC, e.g. COM3.
TCIC User’s Manual
3
Setpoints
Each channel may be defined as a
setpoint
, which means that
the corresponding output will turn on upon crossing some level.
The setpoint user-defined selection also controls the
direction
of
the ‘setpoint indication’; that is, turn the output on upon crossing
the limit either
upwards
or
downwards
. In other words, the
direction
of the trigger is user-defined. Likewise, the user may
define a
hysteresis
behavior, e.g., the output turns on when the
temperature goes above some limit and only goes off again when
the temperature falls below another (lower) limit, thus eliminating
undesirable fluctuations in the status of the output.
TCIC User’s Manual
4
2. Installation
(The following description refers to Windows XP. Obviously, on
another operating system it might be different.)
1. Make sure that all package files have been copied – and
unzipped if necessary – to your hard disk.
2. Two types of drivers are available. Install the one that
meets best your requirements. Note that only one
driver may be installed at the same time. That is, if
for some reason you want to switch to the other driver,
first uninstall the retired one.
• The direct driver provides access via a DLL supplying
functions to directly control the device.
• The VCP (Virtual COM Port) driver would make the
TCIC appear as a spare COM port on the PC, e.g.
COM3.
Consider which driver is best for you and proceed
accordingly to step 3 or 4.
3. Installing the Direct DLL Driver:
3.1 If the VCP (Virtual COM Port) Driver is installed,
uninstall it as follows:
Click: Start – Control Panel – dd or Remove Programs –
FTDI USB Serial Converter Drivers – Change/Remove
Disconnect all TCIC boards from the USB port and click
Continue…
TCIC User’s Manual
5
Click Finish.
3.2 Disconnect or disable the internet communication if
such exists. The reason for that is that there are cases
where the installation procedure automatically
communicates with manufacturer’s site, which might lead
to wrong operation.
3.3 Connect the TCIC card to your PC.
3.4 The ‘Found New Hardware Wizard’ appears.
Select the last option like this:
TCIC User’s Manual
6
3.5 Press Next and select the second option:
3.6 Press Next and browse to the Direct DLL driver folder:
TCIC User’s Manual
7
3.7 Click Next…
3.8 Press Continue nyway…
TCIC User’s Manual
8
Click Finish – that’s it!
Questo manuale è adatto per i seguenti modelli
1
Altri manuali Omega Engineering Hardware di rete
Manuali Hardware di rete popolari di altre marche
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuale utente
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuale utente
Yudor
Yudor YDS-16 Manuale utente
D-Link
D-Link ShareCenter DNS-320L Manuale utente
Samsung
Samsung ES1642dc Istruzioni per l’uso
Honeywell Home
Honeywell Home LTEM-PV Istruzioni per il montaggio
