Omnimount UCL Manuale utente

UCL Installation Guide

Index

Mounting the Wall Plate

Mounting to Wooden Stud

Mounting to Masonry

Mounting the Cantilever Assembly

Configuring the UM-1 Adaptor Plate

Mounting the Display

Adjusting the Display

Roll Control

Vertical Tilt

Swivel

180° Pan

Stowing the Screen

Mounting the Wall Plate

Mounting to Wooden Stud

1. Determine the location where you want the display mounted on the

wall.

2. Use stud finder to locate and mark the center of the two studs.

3. Remove Plasma CL from box. Remove UM-1 Adaptor plate from the

Mounting Head, and set the four 3/8”-16 button head cap screws aside

for later.

Note that the cantilever arm is mounted at the end of the wall plate for

shipping.

4. Remove cantilever arm from Wall plate.

5. Align center mounting holes of wall plate with center marks on studs.

Using the wall plate as a template, mark the mounting holes and center

J box hole. Install J box as required.

Note: Electrical outlets should only be installed by a qualified

electrician.

6. Drill mounting holes with 9/32” bit. Mounting holes should be 3”

(76 mm) deep.

Mounting to Masonry

1. Using the wall plate as a template, mark the mounting holes in the

desired mounting location.

2. Drill mounting holes with 3/8” (10mm) masonry bit. Mounting holes

should be a minimum of 2 9/16” (65mm) deep.

3. Insert masonry mounting anchors (not supplied) into holes, and tap

flush with hammer.

Proceed to

Mounting Cantilever Assembly

1. Important: for the display to be centered over the wall plate when

the cantilever arm is folded, the arm will need to be offset by

approximately 4” (10.1 cm) from the desired center position of the

screen. To do this, first note where the desired center of screen position

intersects the wall plate, and then mark the wall plate.

2. Attach cantilever arm to the wall plate at the indicated offset

location.

3. Mount cantilever assembly to wall using supplied 3/8” lag bolts.

4. Fold cantilever arm to verify center location of mounting head.

Note:

the mounting head will be centered with the arm folded in one

direction only.

Center

screen

mountin

hole

offset

Cantilever

arm

assembl

Configuring the UM-1 adaptor plate

Measure display

The UM-1 ships with a standard set of mounting rails pre-installed.

These rails will fit a display where the vertical distance between

mounting lands on the display are 17 1/8” or less. If your display is

larger than this, you will need to install the large set of mounting rails,

which are included with the UM-1. Please see Install Mounting Rails at

the end of this section for details.

Set UM-1 width

The UM-1 is capable of handling a wide range of landed insert widths.

Measure the horizontal distance between mounting lands on your

display, and set the width of the Mounting Rails as shown,

Standard Range: 38 ½” (98 cm) to 15 ¾” (40 cm)

Standard Configuration

For standard range configurations, loosen the screws on the sliders using

the supplied Allen wrench, adjust rails to desired width, and then re-

tighten screws.

Narrow Range: 15 ½” (39 cm) to 3 ½” (9 cm)

Narrow Configuration

For narrow range configurations, flip slider/rail assembly over (as shown

below) before inserting them into the channels.

Secure sliders and back plate

Secure sliders with (8) button head screws.

For

medium and narrow displays

, where the nuts on the slider are

beneath the back plate, thread button head screws through the back

plate and into the slider as shown.

Note:

The ou er co ne s of the back pla e must always be secured with a

screw.

t r r t

For

wide displays

, where the nuts on the slider are positioned outside of

the back plate, use lock nut with button head screws (supplied) to

secure the back plate, as shown at right.

Mount UM1 to Display

Hardware Selection

a. Consult the supplied Hardware Cross Reference List.

b. Select the mounting hardware for your display.

Attach UM-1 to Display

a. Position the UM-1 over back of display.

b. Thread mounting screws through square washers and spacers (if

required), as shown.

c. Thread mounting screws through slots on side rails into landed

inserts, and secure loosely.

d. With mounting screws installed, center UM-1 on the back of the

display, and then tighten all screws securely.

CAUTION: Do not use power tools or over-tighten the mounting screws.

Install Mounting Rails

1. Remove slider retaining screws as shown.

2. Remove sliders from channels.

3. Select required side rail size:

Medium rail – up to 17 1/8” height of landed inserts

Large rail – up to 25” height of landed inserts

4. Attach selected side rails to sliders as shown.

5. Re-install slider assemblies into channels as shown, and return to Set

UM-1 Width section.

Mounting the Display

1. Locate the set of four 3/8”-16 button head cap screws removed at the

beginning of the installation.

2. Thread two of the screws approximately a ¼” (.6 cm) into the upper

set of PEM nuts on the adaptor plate, as shown.

3. With the help of an assistant, carefully lift the display and hang it

onto the Plasma CL by dropping the exposed portion of the screws down

into the key slots on the nose piece of the Plasma CL.

4. With the display hanging on the mount, thread the second set of

screws into place, and then tighten all four screws securely.

Display Adjustments

Roll Control

Function - Horizontal leveling of the display.

Operation - Grasp the sides of the display, and roll it into the desired

position.

Adjusting Roll Tension – Roll tension is controlled by the two tension

bolts located on the outer edges of the nose piece. Use an open-ended

9/16” wrench to make adjustments to the tension bolts by inserting

wrench between the nose piece and the adaptor plate.

Vertical Tilt

Function – raising and lowering the screen edge to improve viewing

angle/picture quality.

Operation – Loosen tilt tension screws with supplied 3/16” Allen wrench

as shown. Adjust display for desired tilt angle. Re-tighten tension

screws.

Swivel

Purpose – Optimize viewing angle for off center viewing positions.

Operation – Grasp edges of display and swivel into desired position.

Adjust swivel tension – Adjust tension with supplied 3/16” Allen wrench.

180° Pan

Purpose – Allows display to be positioned perpendicular to wall.

Operation – Extend cantilever arm completely. Fully swivel display in

desired direction.

Note: Maximum screen size for full 180° Pan is approximately 50”.

Stowing the Screen

Purpose – Allows display to be folded flat to the wall.

Operation – Grasp center pivot point of cantilever arm and edge of

display. Fold arm in half at pivot point and push display back flat

against wall.

Centering the Screen

The screen will be centered with the cantilever arm folded in one

direction only, as shown.

Indice

Altri manuali Omnimount Supporto TV

Omnimount

Omnimount CI120TPL Manuale utente

Omnimount

Omnimount 1004186 Manuale utente

Omnimount

Omnimount 10239 Manuale utente

Omnimount

Omnimount 37FB-T Manuale

Omnimount

Omnimount 1100167 Manuale utente

Omnimount

Omnimount 10034 Manuale utente

Omnimount

Omnimount OE150T Manuale utente

Omnimount

Omnimount 10322 Manuale utente

Omnimount

Omnimount LEDW60 Manuale utente

Omnimount

Omnimount OC100T Manuale utente

Omnimount

Omnimount VB60LED Manuale utente

Omnimount

Omnimount VB60LED Manuale utente

Omnimount

Omnimount 10321 Manuale utente

Omnimount

Omnimount WM1-L Manuale utente

Omnimount

Omnimount OC80FM Manuale utente

Omnimount

Omnimount NC200-F Manuale utente

Omnimount

Omnimount OL200FT Manuale utente

Omnimount

Omnimount WM1-M Manuale utente

Omnimount

Omnimount PRO HD CART Manuale utente

Omnimount

Omnimount MORELLO 40 Manuale utente

Omnimount

Omnimount OC40FMX Manuale utente

Omnimount

Omnimount Silhouette 65 Manuale utente

Omnimount

Omnimount OC120T Manuale utente

Omnimount

Omnimount CI120FMX Manuale utente

Manuali Supporto TV popolari di altre marche

Ergotron

Ergotron Neo Flex Cantilever UHD Manuale utente

StarTech.com

StarTech.com FPCEILBTB Manuale utente

VonHaus

VonHaus 05/038 Manuale utente

Techlink

Techlink ECHO TV Manuale utente

Sandstrom

Sandstrom SSTVMC12X Manuale utente

Sony

Sony SU-WL700 Guida

ICW

ICW SCACC18 Manuale utente

LG WM-L640V Manuale utente

Gembird

Gembird WM-65ST-01 Manuale utente

ERARD

ERARD FiTUP XXL 035320 Manuale utente

PEERLESS

PEERLESS PLCK-1 Guida

Kanto

Kanto RCF180 Manuale utente

GEM

GEM GEM GP001 Manuale utente

Gladiator Joe

Gladiator Joe GJ0A0053 Manuale utente

Vivotek

Vivotek AM-105 Manuale utente

Vivo

Vivo VESA STAND-VAD1B Manuale utente

AmazonBasics

AmazonBasics B07QG3LMG4 Manuale utente

Secura

Secura QLF210 Manuale utente