Omron Sentech STC-SC202POEHS Manuale utente
No.12S162-03
1/47
STC-SC202POEHS / SB202POEHS
Users guide
GigE Vision Camera
UXGA Color / Monochrome CCD
STC-SC202POEHS / STC-SBC202POEHS
User’s Guide
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *[email protected] *http://www.aegiselect.com
No.12S162-03
2/47
STC-SC202POEHS / SB202POEHS
Users guide
Table of Contents
1 Connector Specifications ..................................................................................................................................... 3
1.1 RJ45 Connector ...................................................................................................................................................... 3
1.2 Power-I/O connector ............................................................................................................................................... 4
1.2.1 Equivalent Circuit for the Input Pin of the I/O Connector .................................................................................... 6
1.2.2 Typical Input circuit .............................................................................................................................................. 7
1.2.3 Typical output circuit ............................................................................................................................................ 7
1.2.4 Input and Output Signal Timing (Hardware Trigger) ........................................................................................... 8
1.2.5 Input and Output Signal Timing (Software Trigger) ............................................................................................. 9
1.2.6 Trigger Signal Processing Process ................................................................................................................... 10
2 Camera Output Timing Charts ........................................................................................................................... 11
2.1 Horizontal Timing ...................................................................................................................................................11
2.1.1 Color Bayer Order (This information is only for STC-SC202POEHS) ...............................................................11
2.2 Vertical Timing ....................................................................................................................................................... 12
2.2.1 Full Scanning ..................................................................................................................................................... 12
2.2.2 AOI (Area of Interest) ........................................................................................................................................ 13
Pixel Transferring Image ....................................................................................................................................... 14
1.1
3 Camera Operational Modes ................................................................................................................................ 15
3.1 Normal Mode ........................................................................................................................................................ 15
3.2 Pulse Width Trigger Mode .................................................................................................................................... 15
3.2.1 Timing ................................................................................................................................................................ 15
3.2.2 Exposure Timing with the Positive Polarity Trigger Signal ................................................................................ 16
3.2.3 Exposure Timing with the Negative Polarity Trigger Signal .............................................................................. 16
3.3 Edge Preset Trigger Mode .................................................................................................................................... 17
3.3.1 Timing ................................................................................................................................................................ 17
3.3.2 Exposure Timing with the Positive Polarity Trigger Signal ................................................................................ 18
3.3.3 Exposure Timing with the Negative Polarity Trigger Signal .............................................................................. 18
3.4 Edge preset trigger mode (The trigger input while the image is out) .................................................................... 19
3.4.1 Timing ................................................................................................................................................................ 19
3.4.2 Exposure Timing with the Positive Polarity Trigger Signal ................................................................................ 20
3.4.3 Exposure Timing with the Negative Polarity Trigger Signal .............................................................................. 20
3.5 H Reset Mode ....................................................................................................................................................... 21
4 Communication Protocol.................................................................................................................................... 22
4.1 Communication Method ........................................................................................................................................ 22
4.2 Communication Settings ....................................................................................................................................... 22
4.3 Communication Format ........................................................................................................................................ 22
4.4 Camera Control Command ................................................................................................................................... 25
4.4.1 Camera Command List (Device Code: 000000) ............................................................................................... 25
4.4.2 Camera Command List (Device Code: 100000) ............................................................................................... 27
4.4.3 Descriptions of the Camera Commands (Device code: 000000); ..................................................................... 29
4.4.4 Descriptions of the Camera Commands (Device code: 100000); ..................................................................... 34
4.1 GenICam Command / Camera Command Reference Table ................................................................................ 41
5 Saving and Loading a User Set data ................................................................................................................. 44
5.1.1 When the Camera is Saving the Parameters .................................................................................................... 44
5.1.2 When the Camera is Loading the Parameters .................................................................................................. 44
5.1.3 When the Camera is Running ........................................................................................................................... 45
5.1.4 Camera initialization (Factory Defaults) ............................................................................................................ 45
6 Revision History .................................................................................................................................................. 46
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *[email protected] *http://www.aegiselect.com
No.12S162-03
3/47
STC-SC202POEHS / SB202POEHS
Users guide
1 Connector Specifications
1.1 RJ45 Connector
This product is NOT a PoE type. Apply power (+10.8 to +26.4Vdc) ONLY through the I/O connector.
Pin Assignment: LED Information:
Pin No.
Signal Name
1 TA+
2 TA-
3 TB+
4 TC+
5 TC-
6 TB-
7 TD+
8 TD-
Please use a 1Gb supported NIC, Network Switch and LAN cable. Check that the NIC and Network
Switch being used is “1Gb transferring”.
NIC and Network Switch support 1Gb. Please confirm the setting on 1Gb transfer.
As for the actual connection, please refer another document “System_Configuration”.
.
Green LED
Yellow LED
Status
Green Light ON Orange Light ON Power ON
Green Light ON Orange Light Blinking 1Gb Transferring
Light OFF Orange Light Blinking 100 Mb Transferring
DC Iris Lens Connector
RJ45 Connector
Green light: OFF
Yellow light: Blinking
100 Mb Transferring
Green light: ON
Yellow light: Blinking
1 Gb Transferring
The camera is powered-on
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *[email protected] *http://www.aegiselect.com
No.12S162-03
4/47
STC-SC202POEHS / SB202POEHS
Users guide
1.2 Power-I/O connector
HR10A-7R-6PB（Hirose）or equivalent
This connector is for the power supply (12Vdc) and input /output signals.
Use HR10A-7P-6S (Hirose) or equivalent for the cable side.
Pin Assignment
Output signals can be assigned through the camera setting communication.
(Device Code = 00H, Command = F0H and F1H)
IO Signal Patterns for Pin No.2 (I/O-1) and Pin No.3 (I/O-2)
Note: I/O-1 can be assigned only by F0H[3..0] and F1[3], and I/O-2 can be assigned only by F0H[7..4] and F1[4].
Pin No.
Signal Name
IN / OUT
Voltage
1 GND IN 0V
2 I/O-1 OUT Open Collector
3 I/O-2 OUT Open Collector
4 TRG_In- IN Low: Smaller than +1.0V (Opt. Isolated -)
High: +3.0 to +26.4V (Opt. Isolated +)
*potential difference between TRG_In- and
TRG_In+
5 TRG_In+ IN
6 POWER IN IN +10.8 to +26.4 Vdc
Command No.
GenICam
F0H[3..0]
F1[3]
F0H[7..4]
F1[4]
I/O-1 (Pin No.2) / I/O-2 (Pin No.3)
For I/O-1 (Pin No. 2)
For I/O-2 (Pin No.3)
0H
(initial setting) - 0H - FrameTriggerWait
(initial setting for I/O-1)
1H Set Value 1H Set Value UserOutput
2H - 2H
(initial setting) ExposureActive
(initial setting for I/O-2)
3H - 3H - TriggerAuxiliary
4H - 4H TriggerInternal
5H - 5H SensorReadOut
6H - 6H StrobeSignal
7H-FH - 7H-FH - For Test Use Only
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *[email protected] *http://www.aegiselect.com
No.12S162-03
5/47
STC-SC202POEHS / SB202POEHS
Users guide
1) FrameTriggerWait
The user can check the camera condition (camera exposure and image output processing by the trigger signal with
this FrameTriggerWait signal).
This signal is LOW for the period from the trigger input signal to the image output.
a) High status (3.3V): No processing by the trigger signal. The camera accepts the trigger signal.
b) Low status (0V): The camera is exposed and the image output processes by the trigger signal.
The camera default setting is the input trigger signal is INVALID while at the low status of this signal. When the
exposure starts while the image output by the next trigger signal, please change the camera setting (Device code:
00H, Command No. :13H) to accept the trigger signal while the image outputs.
The noise appears on the image when the exposure begins while the image is output. The noise appears on the
image when the start exposure while the image is output. In this case, please change the “H reset” for the exposure
start mode (Device code: 00H, Command No. : 12H) to change the exposure start point to the next HD timing.
2) UserOutput
The status of the UserOutput signal can change with the “UserOutputValue”.
3) ExposureActive
The user can check the exposure time with the ExposureActive signal.
4) TriggerAuxiliary
The TriggerAuxiliary signal is the input trigger signal.
5) TriggerInternal
The TriggerInternal signal is the input trigger signal with the trigger delay time.
6) SensorReadOut
The SensorReadOut signal is the FVAL signal, which is the image output period of the time.
7) StrobeSignal
The StrobeSignal signal is the strobe control signal.
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *[email protected] *http://www.aegiselect.com
No.12S162-03
6/47
STC-SC202POEHS / SB202POEHS
Users guide
1.2.1 Equivalent Circuit for the Input Pin of the I/O Connector
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *[email protected] *http://www.aegiselect.com
No.12S162-03
7/47
STC-SC202POEHS / SB202POEHS
Users guide
1.2.2 Typical Input circuit
1.2.3 Typical output circuit
Note;
Vcc and pull-up
register can be
configurable.
(+3.0 to +26.4V 3 to 5mA )
Pin2 or 3
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *[email protected] *http://www.aegiselect.com
No.12S162-03
8/47
STC-SC202POEHS / SB202POEHS
Users guide
1.2.4 Input and Output Signal Timing (Hardware Trigger)
Case of “External Hardware Trigger”, “Positive Edge Trigger”, “Edge Preset Exposure”,
Camera internal processing
Output Signal
External hardware
trigger
Photocoupler output
Filtering
Trigger delay
Exposure
Video output
FrameTriggerWait
ExposureActive
TriggerAuxiliary
TriggerInternal
SensorReadOut
StrobeSignal
StrobeSignalDelay on GenICam StrobeSignalOnTime on GenICam
TriggerDelay on GenICam
Up to 15us
For the signal duration, refer to another chapter "Exposure".
ExposureTimeRaw on GenICam
For the signal duration, refer to another chapter "Exposure".
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *[email protected] *http://www.aegiselect.com
No.12S162-03
9/47
STC-SC202POEHS / SB202POEHS
Users guide
1.2.5 Input and Output Signal Timing (Software Trigger)
Case of “Software Trigger”, “Positive Edge Trigger”, “Edge Preset Exposure”,
Camera internal processing
Output Signal
Software trigger,PLC
and Command
FrameTriggerWait
ExposureActive
TriggerAuxiliary
TriggerInternal
SensorReadOut
StrobeSignal
StrobeSignalDelay on GenICam StrobeSignalOnTime on GenICam
ExposureTimeRaw on GenICam
Trigger delay
Exposure
Video output
TriggerDelay on GenICam
For the signal duration, refer to another chapter "Exposure".
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *[email protected] *http://www.aegiselect.com
No.12S162-03
10/47
STC-SC202POEHS / SB202POEHS
Users guide
1.2.6 Trigger Signal Processing Process
External Hardware Trigger or Software Trigger input the camera’s internal process as follows.
Switching Trigger can be done through register access or GenICam commands
Switching point 1 : Switch to Hardware Trigger and Software Trigger
Register: 12H.5=0
Register: 12H.5=1
TriggerSource=Software on GenICam
TriggerSource=Hardware on GenICam
Switching point 2 : Switch to PLC programmable Software trigger and command software trigger
Register: 16H.7-6=00
Register: 16H.7-6=10
GenICam のTriggerSoftwareSource=PLC
GenICam のTriggerSource=Command
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *[email protected] *http://www.aegiselect.com
Questo manuale è adatto per i seguenti modelli
1
Indice
