One Remote RMB4 Manuale utente
User guide, English
OneRemote RMB4 controller installed in a Bang & Olufsen Beo4 remote control.
Operate these devices using the modified Beo4:
Samsung LED TV 7-series and other.
Operate devices that are operate able with RCU’s like:
Samsung most remotes for Samsung digital TV.
User guide type 35104373 RMB4
2
3
Congratulations
With the OneRemote controller installed inside your Bang & Olufsen Beo4
remote control, you can fully operate your non B&O TV with this terminal.
This guide explains how.
If your Beo4 has already been correctly set up, you can now proceed to one
of the two operation tables:
Important ! !
If the OneRemote controller has not yet been optimized for your setup,
refer to the installation section about the initial setup and option program-
ming. There is no programming needed during everyday use.
The OneRemote controller that has been installed inside your Beo4 remote
control, can be used in any Beo4 remote control. Both first generation mod-
els and the latest with extra buttons for manoeuvring, the Beo4 Navi.
To get the most of your modified Beo4, the OneRemote controller must be
programmed according to the Beo4 model and the environment that your
TV is a part of. Refer to page 5 and forward, for the initial setting.
*1 Extra buttons have been added on never Beo4 models, Beo4 Navi. Se page 10.
Page 9
If your Beo4 has enabled Navi buttons . *1
Page 8
In any other case.
4
The OneRemote controller for the Beo4 remote control
The OneRemote controller is a small microcomputer module, which is specifically
made to be built in to a Bang & Olufsen Beo4 remote control.
The controller captures the commands that were meant for operating a Bang & Olufsen
device. Before the commands are emitted from the Beo4, these commands are convert-
ed, and therefore also able to operate a non Bang & Olufsen TV.
Each controller is dedicated for operating a specific product like an Apple iPod docking
station, a flat screen TV, a curtain controller etc.
The controller makes the Beo4 able to operate a third part device, still able to operate
any other Bang & Olufsen products.
If there is a Bang & Olufsen audiomaster in the room, it can be used for handling the sound. Speakers con-
nected to an audiomaster are of a much better quality than the speakers in a TV. In a B&O linkroom setup
with Beolink Active or Beolink Passive, you can also use these speakers to improve sound from most TV’s.
Only a simple audio cable is needed between the TV and the audiomaster. See the option programming sec-
tion about AAUX and PC modes on page 11.
5
Operating with OneRemote.
To be able to operate the non B&O TV optimal using the OneRemote modified Beo4,
the user has to be familiar with the operations available when using the original remote
control, as described in the TV’s user manual.
A beo4 remote control is not equipped with as many keys as most remote controls for
non B&O devices. We have designed an operation ‘layout’ that works logically, even
when shifting between different OneRemote operated devices. To get a common layout
for many devices, we therefore needed to redefine a few of the beo4 buttons to other
functions.
The Beo4 Navi model introduces new buttons, making it easier to make operation
table’s, closer to the TV’s own.
Coloured function buttons.
To make room for easy access to more important functions, in some layouts we have
moved the coloured function buttons, to a lower layer. In these layouts to send a ‘color’
command, a O must be pressed before the coloured button itself.
This way we are able to assign other functions to the coloured buttons in direct mode.
In a OneRemote environment the coloured buttons are often assigned to these opera-
tions:
Go, Navi or Stop shifted operation.
Some of the buttons has two or three operations. To get to these they have to be preced-
ed with O or q.
In case of Beo4 Navi a p button has been a added to replace the O button, when
in ‘mode 2’. In mode 2 the OneRemote uses the Center button for shifting, instead of
O . Refer to page 10.
Buttons that has been assigned secondary functions are listed in the operating table on
page 9.
QGuide, EPG or similar.
EBack, Backup, Return or similar.
W
R
Programme zapping. P+/ P- ,
Channel up/ down or CH+/ CH-.
6
Programme stepping, up/ down manoeuvring in menus.
Most set top boxes and TV’s has 4 arrow buttons for manoeuvring in on-screen menus,
up, down, left and right. In addition they are equipped with separate programme step-
ping buttons for zapping through the programme list. Often these keys are named P+, P
-, CH+ or CH-.
OneRemote often makes use of the Rand the W keys for programme zap-
ping. This way the four up, down, left and right buttons are free to be used for the more
natural use of manoeuvring in on screen menus.
Using a Beo4 Navi in mode 2, manoeuvring in On-screen menus is fully handled using
the added ‘joy-stick’, not available on previous Beo4 models. In a Beo4 Navi setup we
therefore can make use of the up and down arrows for programme zapping.
Setting the Zap Mode Option
If the OneRemote controller is not set to operate in Navi mode, the Beo4 but-
tonsW and R are used for programme stepping. The D and Fbuttons
are used to manoeuvre up and down in an on-screen menu. This is the default factory
setting, as described above.
Selecting the Zap mode buttons:
Enter one of these 2 codes within 10 seconds to set the preffered Programme Zap mode buttons.
LIGHT mq90p The
D
and
F
buttons will be used for pro-
gramme zapping.
LIGHT mq91p The W & R buttons will be used for pro-
gramme zapping.
7
Disabling and Dual TV Option
The OneRemote controller in the modified Beo4 remote control can be enabled or disa-
bled using this option. When disabled the Beo4 remote control operates as a Beo4 that
has not been modified.
In DUAL TV-mode the OneRemote controller enables operation of both a B&O TV and
the non B&O TV which the controller is made to operate.
Disabling and Dual TV mode:
Enter one of these 3 codes within 10 seconds to set the preffered mode.
LIGHT mq20p Disables the OneRemote controller.
LIGHT mq21p Enables the OneRemote controller.
LIGHT mq22p Enables the OneRemote controller in Dual TV mode.
In this mode:
t + 1 starts operating a B&O TV.
t + 2 starts operating the non B&O TV
8
Translation table when not in Navigation mode. * see page 10
Daily operation Text TV operation
t Turns on the TV
w Turns off the TV
OO Enter
W*1*2 Prog + TTV page+
R*1*2 Prog - TTV page -
Q*1*2 Guide
E*1*2 Return TTV Hold
eExit
mSource
om Menu TTV Index
*1 The up/ down arrow operations can be ex-
changed with the blue and yellow buttons. See
page 6.
*2 As the direct function of the coloured func-
tion buttons has been assigned to other func-
tions, these have to be preceded with a o
to retrieve the actual coloured function.
oQ Green function
oW Yellow function
oE Red function
oR Blue function
TEXT Text TV on/ mix
t Text TV off
Playback operations
oPlay press 1 sec.
qq Stop
oq Pause
oA/SRew/ FF
rRecord
Other operations
O1 FAV
O2 Channal list TTV Hide
O3 info TTV Show
O4 Tools TTV Size
O5 Content
O6 Subtitle
O7 Media Play
O9 Internet
Special/ alternative operations
O0 Play
O8 Record
Oe 3D
qe AD
9
Translation table when in Navigation mode. * see page xxxxxx
Daily operation Text TV operation
t Turns on the TV
w Turns off the TV
OO Enter
DF CH+ / CH-
AS REW / FF
Navi buttons are used for manoeuvring in on-
screen menus.
W Yellow key
R
Blue key
Q Green key
E Red key
eExit
BACK Back
mSource
om Menu TTV Index
oQ EPG
oW CH List
oE PRE CH
oR TOOLS
TEXT Text TV on/ mix
t Text TV off
Playback operations
pPlay
qq Stop
oq Pause
rRecord
Other operations
O1 FAV
O2 Channal list TTV Hide
O3 info TTV Show
O4 Tools TTV Size
O5 Content
O6 Subtitle
O7 Media Play
O9 Internet
Special/ alternative operations
O8 Record
Oe 3D
qe AD
10
Beo4 NAVI mode option.
Newer Beo4 models are named Beo4 Navi due to an added special navigation button.
A joystick type control button, placed where previous Beo4 models have a Obutton.
If your Beo4 has a O button, this chapter is not relevant for you !
Use of the Beo4 Navi joystick navigation operation:
Enter one of these 2 codes within 10 seconds to enable or disable the OneRemote controllers use of the ex-
Set the Beo4 Navi remote control in operation mode 2, as described in the B&O user guide that was sup-
plied with your Beo4, if you want to use these. Otherwise select mode 1.
LIGHT mq51p Enable use of the NAVI control.
When the OneRemote controller NAVI mode has been
enabled, use the operation table on page 9.
LIGHT mq50p Disable use of the NAVI control.
When the OneRemote controller NAVI mode has been
disabled, use the operation table on page 8.
Altri manuali per RMB4
18
Indice
Altri manuali One Remote Controllori
