Onn ONA16AV010 Manuale utente
Universal Remote
Model: ONA16AV010
PRODUCT GUIDE
123
6
5
4
789
0
MENU
GUIDE SHIFT
SETUP
TV CBL
INPUT
INFO
SAT
LAST
ENTER
EXIT
2
Congratulations on your purchase of the ONN
Universal Remote. This remote is capable of
operating thousands of video devices, including
TVs, cable and satellite receivers!
IMPORTANT:
SAVE THIS MANUAL AND CODE LIST FOR
FUTURE REFERENCE
QR Code
Scan the QR code to view our helpful
demonstration video for programming your
ONN remote.
Introduction ........................................................... 2
Battery Installation................................................. 3
Care and Maintenance ..................................... 3
Button Functions................................................... 4
Programming Your Remote ................................... 6
Direct Code Entry............................................. 6
Auto Code Search............................................ 8
Master Volume Feature ....................................... 10
Reset to Factory Settings.................................... 11
Troubleshooting................................................... 12
FCC Statement.................................................... 13
Remote Code Section ......................................... 14
Table of Contents
Scan this to view remote
setup video
Mira a ver el video de
instalación remota
www.myonnremote.com
3
Your universal remote requires two (2) AAA
Alkaline batteries (not included).
To Install the Batteries:
1. Remove the battery compartment cover by
sliding the cover down.
2. Match the (+) and (-) symbols on the batteries
to the (+) and (-) symbols inside the battery
compartment, then insert two (2) AAA Alkaline
batteries. Be sure to use fresh batteries.
3. Slide the battery compartment cover back
into place.
Note: If your remote stops operating properly,
replace the batteries with new ones. The remote
will retain the codes you have programmed for up
to 10 minutes after the batteries are removed.
Battery Precautions:
• Donotmixoldandnewbatteries.
• Donotmixalkaline,standard(carbon-zinc),or
rechargeable (Ni-Cd, Ni-MH, etc.) batteries.
• Alwaysremoveold,weakorworn-outbatteries
promptly and recycle or dispose of them in
accordance with local and national regulations.
Care and Maintenance
Do not submerge or rinse remote
under water.
Use and store the remote at normal
household temperatures.
Use a soft, damp cloth to easily clean the
remote’s top surface.
If the remote is not going to be used for a
long period of time, remove the batteries
from the remote. (NOTE: remote will need
to be reprogrammed if the batteries are
removed.)
Handle the remote with care.
Battery Installation
4
INFO
Displays/selects on-screen
channel information, etc.
In SHIFT mode, MENU
displays the Menu on the
TV and other devices.
NUMBERS
Enter numbers for direct
channel selection.
DOT
Used to select digital channels
(forexample:4.1,9.2).
INPUT
Selects the
video inputs from
available viewing sources.
TV, CBL/SAT,
Selects the device
to control.
MUTE
TurnsotheTVsound
while the picture remains.
In SHIFT mode, OK Selects
menu items for the device
you are controlling.
ON•OFF
Turns the device
OnorO.
Red Indicator
Light when
any button is
pressed.
Button Functions
5
SETUP
Used to program the remote.
SHIFT is the alternative
function of this button. Use
the SHIFT button to access
the Menu and Navigation
functions of your device.
To enter the SHIFT mode,
press this button once. To
exittheshiftmode,press
the SHIFT button again.
NOTE: The red indicator
light will blink when the
remote is in SHIFT mode.
VOLUME UP/DOWN
Changes the volume
level of the device,
normally the TV.
CHANNEL UP/DOWN
Changes the channels.
In SHIFT mode, these
buttons navigate on-
screen cursors and are
used to make selections.
LAST
Returns to the previously
selected channel. In
SHIFT mode, EXITexits
on-screen menus.
ENTER
For some TV models, use
after direct channel number
entry to immediately change
to the selected channel.
Button Functions, cont.
6
Programming Your Remote
Your ONN universal remote control is designed to
controlupto2dierentaudio/videodevicessuch
as TV, satellite, cable and audio devices using only
one remote. To use this remote, you will need to
program it to control the devices of your choice.
There are two ways to program the remote —
direct code entry or auto code search.
Direct Code Entry (Recommended)
1. Locate the Remote Code List
provided in this manual. Find the
DEVICE CATEGORY you wish to
program(forexampleTV, CBL/SAT)
andthenndtheBRAND of that
device. Circle all the codes under
thatbrand.Example:ForaGETV,
locate the TV code section then
circlealloftheGETVcodes.
2. Manually turn on the device you
wish to control.
3. Press and hold the SETUP button
until the red indicator light stays on
(approximately2seconds)andthen
release the SETUP button.
4. Press and release the desired device
button on the remote (TV, CBL/SAT).
The red indicator will blink once and
then remain on.
5. Entertherst4-digitcodepreviously
found in the code list using the
number buttons on the remote. If
the code entered is a valid code, the
redindicatorlightwillturno.Ifthe
code entered is not a valid code,
theredindicatorlightwillashand
remain on allowing you to re-enter
the code.
Note: If no buttons are pressed for
35 seconds, the remote will exit the
SETUP mode and you will have to
start over.
7
Programming Your Remote
6. Point the remote at the device.
Press the POWER button—if
thedeviceturnso,nofurther
programming is required for that
device. If the device does not turn
o,returntostep3andusethe
nextcodefoundinthecodelist.
Continue this process until a code
for your device is found.
To view a helpful demonstration video for
programming your ONN remote, see QR code
on page 2 of this manual.
Programming Notes
• Ifyourdevicedoesnotrespondtotheremote
after trying all codes listed or your brand is
not listed in the code list, use the Auto Code
Search method to program your remote.
• Sometimestherstcodethat“works”withyour
device may operate only a few functions of your
device. There may be another code in the code
list that performs more functions. Try other
codes from the code list for more functionality.
• Youcanuseanydevicebuttontocontrolother
devices in your home entertainment system.
Forexample,youcanusetheCBL/SAT device
button to control an audio receiver.
• Writedownthecodefoundtooperateyour
device for future reference.
8
Programming Your Remote
Auto Code Search
The Auto Code Search searches automatically
through all of the codes stored in this remote. Read
all the following steps prior to starting the auto
search as you will need to be prepared to lock in
the proper code when found.
1. Manually turn on the device you wish
to control.
2. Press and hold the SETUP button
until the red indicator light stays on
(approximately4seconds)andthen
release the button.
3. Press and release the desired device
button on the remote (TV, CBL/SAT).
The red indicator will blink once and
then remain on.
4. Point the remote at the device and
press and release the POWER button
to start the search. The red indicator
willash(approximatelyevery2
seconds) as the remote searches.
NOTE: The remote must be pointed
at the device for the duration of this
search.
5. Placeyourngeronthe#1 button so
you are prepared to lock-in the code.
6. Whenthedeviceshutsoorbegins
playing, press the #1 button to
lock-in the code. The red indicator
lightwillturno.NOTE: You have
approximately two seconds after the
device shuts o or begins playing to
lock in the code.
7. Point the remote at the device and
check to see if the remote operates
the device as desired. If it does, no
further programming is required for
that device. If it does not, return to
step 2 and start the auto search.
9
Programming Your Remote
To view a helpful demonstration video for
programming your ONN remote, scan the QR
code on page 2 of this manual.
Programming Notes
• Thisprocessmaytakeseveralminutesasthe
remote contains many codes.
• TheSETUP button can be used during the
search process to reverse the direction of the
searchoftheremotecodes.Forexample,if
you miss the code for your device and the
remote is continuing to search (as indicated by
the blinking red light), press the SETUP button
and the code search will reverse direction and
return to the code.
• WhenusingtheAutoCodeSearch
programming method, the device button
corresponding to the type of device you want
tocontrolmustbeselected(forexample,the
TV device button must be selected in step 3 if
you want to control a TV.
• Sometimestherstcodethat“works”with
your device may operate only a few functions
of your device. There may be another code
in the code list that performs more functions.
Continue the code search as directed above
until the best code is found.
10
Master Volume Feature
Master Volume Feature
The Master Volume Feature allows you to select
a single device (TV or audio receiver) that the
volumecontrolalwayscontrols.Forexample,
the remote can be in TV mode while the volume
buttons control the volume on your audio receiver
instead of your TV.
Enabling the Master Volume Feature
1. Press and hold the SETUP button
until the red indicator stays on
(approximately4seconds)andthen
release the button.
2. Press and release desired device
button (TV, CBL/SAT) for the device
you wish to control the volume.
3. Press and release the
MUTE button.
4. Press and release the VOL + button.
The red indicator will blink twice and
thengoo.
To test the feature put the remote in
another mode such as the TV mode
if you programmed the audio receiver
to be the Master Volume Device.
Point the remote at the audio receiver,
press and hold either the VOL + or
the VOL - button. If the audio receiver
volume changes then the remote is
programmed correctly. If the TV volume
changes and not the audio receiver,
you will have to repeat the steps above
and test again.
Disabling the Master Volume Feature
1. Press and hold the SETUP button
until the red indicator stays on
(approximately4seconds)andthen
release the button.
Indice
Altri manuali Onn Telecomando universale
