ooznest C-Beam Machine Manuale utente
C-Beam Machine
Electrical Assembly Instructions
C-Beam Machine 1
Table of Contents
1.0 Getting Started 2
1.1 About The Kit 3
1.2 Check Product Contents 3
1.3 Tools Required 3
1.4 Notes on Assembly 4
2.0 Power Supply Assembly 5
2.1 Output 6
2.1.1 Securing XT60-Male Outputs ........................................................ 6
2.1.2 Inserting LED-Volt-Meter.............................................................. 7
2.2 Input 8
2.2.1 IEC-Inlet Wires ........................................................................... 8
2.2.2 Attaching IEC-Inlet...................................................................... 9
2.3 Connecting PSU-Cover 10
2.3.1 Connecting Wires ...................................................................... 10
2.3.2 Attaching PSU-Cover ................................................................. 12
2.3.3 Testing .................................................................................... 13
2.3.4 Mounting ................................................................................. 14
3.0 CNC xPro Assembly 15
3.0.1 Terminal-Block Attachment......................................................... 16
3.0.2 Fan Mount Assembly.................................................................. 17
3.0.3 Attaching The CNC-xPro ............................................................. 18
3.0.4 Fans Wiring .............................................................................. 19
3.0.5 Mounting the CNC-xPro Assembly................................................ 20
4.0 Wiring & Commissioning 22
4.1 CNC-xPro Wiring 23
4.1.1 Wiring Mounts .......................................................................... 23
4.1.2 Wire Routing ............................................................................ 24
4.1.3 Connecting the CNC-xPro ........................................................... 26
4.2 Software & Machine Settings 27
4.2.1 Installing Universal G-Code Sender (UGS) .................................... 27
4.2.2 Configuring The Firmware .......................................................... 28
4.3 Testing 29
4.4 Complete 31
5.0 Appendix 33
5.1 Appendix A - Kit Contents 34
6.0 Appendix B 39
6.1 Recommended GRBL Settings 40
C-Beam Machine Getting Started 2
1.0 Getting
Started
C-Beam Machine Getting Started 3
1.1 About The Kit
The C-Beam Machine is a perfect Hobby CNC to manufacturer custom pates out of wood,
plastics, or even aluminum. In many projects it happens, that an off the shelf plate does
not suit your needs, a C-Beam machine is the solution to this problem. A C-Beam Machine
offers the freedom to create the custom plates you need, right away, no long waits, no
extortionate prices.
Instructions to build the mechanical portion of the machine can be found by watching this
video: https://www.youtube.com/watch?v=HVR8pABCHXI
This manual mainly covers the electrical setup of the machine. Ideally, this kit should be
started straight after completing the mechanical assembly. This kit aims to provide you
with what you need to turn the mechanical kit into a working moving machine. To go
from this kit to a machine which can begin cutting, you will need a router and a spoiler
board with a system to mount the workpiece that you wish to cut.
The C-Beam machine has a very large community of users, who can mostly be found at
http://openbuilds.com. It is free to sign up to this community and it will allow you to
share your builds, interact with other members, and download useful community created
resources. There is a specific build thread for the C-Beam Machine, and we would love to
see your machines and what you make with them: http://openbuilds.com/builds/c-
beamTM-machine-plate-maker.2020/
1.2 Check Product Contents
Apart from the mechanical portion, when you receive your kit, the first thing you should
do is to check the contents against the list in Appendix A. The majority of the parts will be
separated into boxes that correspond to the subsections in this manual. Additional spare
small parts will be included. If anything is missing or damaged (or if you have any other
as quickly as possible.
1.3 Tools Required
•The list below shows the main tools that will be required to complete this build:
•2.5mm Allen Key
•3.0mm Allen Key
•4.0mm Allen Key
•5.5mm Spanner
•7.0mm Spanner
•8.0mm Spanner
•Hammer
•Selection of Philips Screwdrivers
•Selection of Flathead Screwdrivers
•Tweezers
•Wire Cutters/Strippers
C-Beam Machine Getting Started 4
1.4 Notes on Assembly
The assembly has been split into 4 sections: Power Supply Assembly, CNC xPro
Assembly, Wiring & Commissioning. To make locating parts quicker, leave the parts in
the boxes they came in when carrying out the build.
It is recommended that you read through the whole manual before beginning the build in
order to get a full picture of the assembly process. Before beginning each step, make
sure you have studied the diagram and have the required parts in front of you. A PDF
version of the manual is available on our website and this will allow you to zoom in on the
diagrams if needed.
Be very careful to not over tighten the nuts and bolts on the plastic parts, otherwise they
may crack. Everything should easily fit together, and so if it isn’t, take a step back and
re-read the instructions.
Assembly of this kit involves the use of electricity and therefore you should take appro-
priate precautions to ensure you are assembling the kit in a safe manner. When following
wiring diagrams, double check that everything is connected correctly. Before carrying out
any work on the electrics make sure that the machine is switched off.
The polarity is indicated by the color of the wire, not by the color of the connectors at
each end. A positive wire is red or brown, negative is black, and earth is green and yel-
low.
The controller is sensitive to electrical interference. Therefore we are now providing an
interference kit with machine to reduce this. In this kit ferrite beads are provided. Clip
the Motor-Ferrite's on the motor wires as close as possible to the CNC-xPro. Clip the PSU-
Output-Ferrite's on the PSU-Output-Power-Cable as close as possible to the 24V-360W-
Power-Supply. And the Router-Ferrite, as close as to your router as possible.
C-Beam Machine Power Supply Assembly 5
2.0 Power
Supply
Assembly
C-Beam Machine Power Supply Assembly 6
2.1 Output
2.1.1 Securing XT60-Male Outputs
A. Insert the XT60-Male connectors into the provided insets on the PSU-Cover. They
should sit flush with the front of the PSU-Cover. Completion of this kit only requires 2
x XT60-Male connectors. The left-most XT60-Male connector is not needed for the
operation of this machine, but is included so you have the option to add additional
accessories. For safety reasons, if you do not intend to use it, do not attach it to the
PSU-Cover, and leave that inset empty.
B. Secure each XT-Male connector using 2 x Plastite-Screw-M2.5-8mm through the holes
provided on the securing tab as seen on the internal view. When initially placing the
screw, it is helpful to hold each screw in place using tweezers or long nose pliers.
C-Beam Machine Power Supply Assembly 7
2.1.2 Inserting LED-Volt-Meter
A. Gently push the LED-Volt-Meter into the provided gap on the top of the PSU Cover.
The wires on the LED-Volt-Meter should be oriented to the front of the PSU-Cover.
C-Beam Machine Power Supply Assembly 8
2.2 Input
2.2.1 IEC-Inlet Wires
A. Attach the receptacle end of the IEC-Inlet-Live-Wire, IEC-Inlet-Neutral-Wire & IEC-
Inlet-Earth-Wire to their respective terminal tabs on the IEC-Inlet, as seen in the
above image.
Indice
Altri manuali ooznest Utensili elettrici
