Opex OMATION 2112 Manuale utente
User Manual
Model 2112
June 2015
Omation Model 2112 User Manual (OPEX part no. #7585180)
Copyright © 2015 OPEX®Corporation
All rights reserved. Printed in the United States of America.
If you find errors, inaccuracies, or any other issues or concerns with this
document, please contact the OPEX Technical Writers via email at:
No portion of this manual may be reproduced in any form or by any means, or
stored in a database or retrieval system, without the express, written
permission of OPEX®Corporation.
To request permission, contact:
OPEX®Corporation
ATTN: Legal Department
305 Commerce Dr.
Moorestown, NJ 08057-4234
Revision Tracking
Date Chapter(s) Notes Rev
Mar. 2012 Initial Release A
Jun 2015 Added Japanese specs B
Table of Contents 3
Omation Model 2112 User Manual - OPEX Corporation use only - not for distribution
Table of Contents
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Routine maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Optional assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4Safety
Omation Model 2112 User Manual - OPEX Corporation use only - not for distribution
Safety
• Read and understand all aspects of the user manual before operating this
equipment.
• Keep hands, hair, loose clothing and jewelry away from moving parts.
• Lifting and or moving of this equipment requires two persons.
• Unit must be placed securely on table/surface that is properly rated for
accumulated load weight.
• Use of this equipment is limited to its intended function, that of opening mail.
• Do not place fingers in the feed or cutter areas while running the machine.
• Do not operate this equipment with the cover doors removed.
• Do not set liquids on the Model 2112 which could spill into the machine.
• Before cleaning, make sure all power is disconnected.
• Do not use high pressure “canned air” that is marked flammable to clean
paper scraps and dust from the machine.
• Turn off the machine during periods of non-use.
Overview
The Omation Model 2112 is a high-speed envelope opener that can open and
keep count of 400 six-inch envelopes per minute (processing speed depends
on the length and thickness of mail). Some other features include:
• Advanced self-adjusting feeder for efficient mixed mail opening
• Mill cutter can remove as little as 0.010” of a chip
• Enhanced chip management/chip capacity
• Two position depth of cut, or no cut (for counting mail only)
• Large variety of mail types
Safety 5
Omation Model 2112 User Manual - OPEX Corporation use only - not for distribution
Cut/No Cut Function
The Omation 2112 is capable of counting individual pieces of mail with or
without cutting open the envelope. This function can be selected by turning the
Cut/No Cut Knob to the desired selection position.
Counter Function
This displays the count for individual pieces of mail processed in either the “No
Cut” or “Cut” mode. Even if power is lost to the machine or the machine is
turned OFF, the Omation 2112 will maintain the count total. Once the Counter
is reset, the previous count is lost. The condition of the mail and the cleanliness
of the machine can effect the accuracy of the count.
6Introduction
Omation Model 2112 User Manual - OPEX Corporation use only - not for distribution
Introduction
Figure 1: Omation 2112 main components
Operation
Refer to Figure 1 for component locations.
1 Connect the power cord to the Omation 2112 and into an AC supplied
outlet.
Note: When you first connect the power cable, the Chip Bin Full Indicator
Light will flash. This is because the machine cannot determine if the
chip bin is full and needs to be emptied. Open the bin and empty the
chips (if any). Removal and replacement of the chip bin resets the
indicator. An internal counter (not the one on the display) will count up
to 3500 envelopes before flashing again to inform you to empty the chip
bin.
Counter reset button
LED count indicator window
Output tray
Chip bin
Cut/no cut selector knob
Cutter depth lever
Chip bin full indicator light
Envelope feed
On/Off switch
Retard assembly
Feed thumper
Nip arm assembly
hopper
Introduction 7
Omation Model 2112 User Manual - OPEX Corporation use only - not for distribution
2 Select either the “No Cut” (clockwise) or “Cut” (counterclockwise) position
on the Cut/No Cut Selector Knob.
3 Set the cut depth lever to the left (deep cut) or right (shallow cut). The
factory cut depth default settings are .020” (deep) or .012” (shallow).
However, the cut depth can be adjusted, as described in “Cutter
Adjustment” on page 9.
4 Press the Counter Reset button to reset the counter (if desired).
5 Load a handful of mail (approximately 50 pieces) onto the Envelope Feed
Hopper. Be sure to justify the side of the mail to be cut against the back of
the Feed Hopper. The Feed Thumper (a rotating cam) helps to jog the mail
for improved feeding.
6 Turn the On/Off Power Switch to the On position to start the machine.
7 The mail is singulated (separated one at a time) by the retard assembly.
8 The nip arm assembly guides the individual envelopes past the cutter and
to the output tray.
9 Once the Envelope Feed Hopper is empty, empty the output tray.
10 To continue processing, repeat the above steps.
Nip Arm Removal/Installation
The Nip Arm should be removed for clearing paper jams and cleaning the
machine.
8Introduction
Omation Model 2112 User Manual - OPEX Corporation use only - not for distribution
Figure 2: Nip Arm removal
To remove the Nip Arm, turn the machine OFF. Press the nip arm latch to the
left (see Figure 2), grasp the right end of the Nip Arm, pulling upward and
remove. Reverse this procedure to re-install the Nip Arm. The Omation 2112
will not operate until the Nip Arm is properly installed.
Also, the nip arm assembly must be removed if you want to increase/decrease
the cut depth from the factory setting. Setting the cut depth is described on
page 9.
Press nip arm latch
Lift up and remove
Introduction 9
Omation Model 2112 User Manual - OPEX Corporation use only - not for distribution
Cutter Adjustment
The cutter on the Model 2112 can be adjusted to accommodate different mail
types, allowing for a deeper or shallower cut than what the cutter adjust lever
provides.
To adjust the cutter depth
1 Remove the nip assembly (see “Nip Arm Removal/Installation” on page 7).
Figure 3: Cutter adjustment detail
2 Reference Figure 3 and make adjustments as described below:
- For a deeper cut - push the release button and with a Phillips head screw-
driver, turn the cutter adjust cam clockwise one notch to increase the cut
by 0.002”.
- For a shallower cut - push the release button and with a Phillips head
screwdriver, turn the cutter adjust cam counterclockwise one notch to
decrease the cut by 0.002”.
3 Replace the nip assembly.
Release button
Cutter adjust cam
10 Introduction
Omation Model 2112 User Manual - OPEX Corporation use only - not for distribution
Output tray position
You can adjust the position of the output tray, if needed, for processing larger
envelopes. The output tray can be in one of three positions: against the
machine, one inch away, or two inches away.
Figure 4: Output tray extended
Simply lift the output tray up, move it to the desired position, and press it down
onto the stepped tray hitch (see Figure 4).
Stepped tray hitch
Output tray
Indice
Altri manuali Opex Sistema di posta digitale
