Optex inSight INS-HX-80N Manuale utente
59-xxxx-0 2102-10
EN
CAD 絵は線画に差替え予定
INS-HX-80N
INS-HX-80N
Camera and PIR detector
INSTALLATION INSTRUCTIONS
1
2
3
4
5
6
- Parts identification
- Accessories
- Manufacture’ s statement
- Detection area
- Specifications
- Compliance
- How to reset to the factory default
Before installation
Others
<< Contents >>
- 1 -
1-1. Disassemble
1-2. Mounting
1-3. Fall prevent wire
1-4. Wiring
1-5. Assembling
4-1. PIR area direction
4-2. Detection range limit
4-3. Adjusting the vertical angle
4-4. Switch settings
4-5. Walk test
4-6. LED indicator
Page
2
3
5
6
12
13
14
IP camera settings
CHeKT settings
Step
IP camera settings
CHeKT settings
https://navi.optex.net/manual/50427
https://chekt.com/registration
Enable
Disable
Installation
IP address settings
Registration InSight to CHeKT portal site
DHCP
Detection area settings and walk test
Camera angle settings
System check
- Manufacture’ s statement
Mounting height
2.5 m (8’ 2” ) to 3.0 m (10’ )
Failure to follow the instructions provided
with this indication and improper handling
may cause death or serious injury.
Failure to follow the instructions provided
with this indication and improper handling
may cause injury and/or property damage.
Check mark indicates recommendation.
Nix sign indicates prohibition.
Special attention is required to the section
of this symbol.
Symbol Meaning Symbol Meaning
Warning
Caution
NOTE
Warning
Caution
Tilt
Before installation
- Parts identification - Accessories
4 x 20 mm
Mounting screws
T20 Torx wrench
Waterproof cap
for LAN connection
Bracket angle adjus�ng screw
PIR Cover Camera angle adjus�ng screw
Back cover
PIR detector
Camera unit
- 2 -
Mounting plate
1Installation
Step
Remove the main unit and the mounting plate.
123
1-2. Mounting 1-3. Fall prevent wire
Hook the fall prevent wire.
1-1. Disassemble
- 3 -
1-5. Assembling
Replace the main unit with the mount base.
12
1
Installation
Step
- 4 -
Put the main body back on mounting plate.
Caution Do not pinch the cable when restoring the PIR detector.
1-4. Wiring
PoE LAN cable
DC power cable
12 V DC power for camera and PIR
8-pin I/O cable
Tamper
Alarm
Power
+- SP N/A COM AL TP TP
Pink
Orange
Yellow
Brown
Green
Purple
Black
Red
Do not connect to
the N/A terminal.
Waterproof cap
for LAN connection
Caution
The connector can be fixed inside
the main body with double-sided tape.
NOTE
Cut the rubber and put the LAN cable into
(a), then (b) will be assembled to (a) tightly.
As a final step, (c) need to be assembled
to (b) without making any space.
2IP address settings
Step
The default network type of InSight is dynamic. If you do not have a DHCP server,
access the following IP address. Change the InSight network type to Static and set
the IP address;
Initial address: Refer to the label on the InSight
User name: root
Default password: OPTEX
Refer to the “IP Camera Setting Manual” in more detail.
3Registration InSight to CHeKT portal site
Step
- 5 -
The default network type of InSight is dynamic. If you have a DHCP server, it will automatically set the IP address.
1. Setup your CHeKT Dealer Portal:
2. Before getting started with CHeKT, you will need access to a CHeKT dealer web portal.
Access to this portal allows you to install and manage the InSIght series.
If you do not have an account, please request a dealer account by visiting:
www.chekt.com/registration
Refer to the “https://support.chekt.com” for more detail.
IP camera settings
CHeKT settings
Detection area settings and walk test
4
Step
1
2
Caution
Do not use the vertical angle adjustment of the main unit other than adjusting
the detection area surface to be parallel to the ground inclination.
Pall all el Adjusting the detection range
Remove the Back cover by hand.
Raise the Back cover up.
Pull it back.
Adjust PIR area direction
Angle can be adjusted with either left or right screw.
4-1. PIR area direction
12
The display of the detection area helps to set the area.
- 6 -
Settings on the InSight web
It is possible to refer the location of the detection area following procedure.
SETUP -> PIR DETECTOR -> PIR area viewer
In this step, do not change the camera tilt angle on InSight web settings.
Horizontal ±95°
Vertical 0° to -20°
1
2
[ Mounting height ]
3.0 m: 1 click downward
2.5 m: Default setting(No click)
NOTE
IP camera settings
4
Step
Detection area settings and walk test
Masking flap and plate
Upper flap
Plate 1
Lower flap
Plate 2
Flap fix position
indicator
Plate fix position
indicator
Open the PIR cover
4-2. Detection range limit
1
2
- 7 -
The detection distance in the following table can be limited by combining the positions of the flap. Use the following
table to determine the positions of the upper and lower flaps that set the required max. detection distance.
PIR long range detection area reduction
HOW TO REDUCE THE LONG RANGE DETECTION AREA
a
b
d
g
i
h
j
C
Flap fix position
indicator
Upper flap
Lower flap
a
b
g
i
C
a
b
g
i
C
b
i
C
Pull out the flap.
Move the flap to the position that corresponds
with the desired detection distance.
Push the flap until it clicks into the position.
If the lower flap is located
at the factory default position,
slide it out with your thumb.
To adjust the LONG range of detection, set
the upper and lower flaps as follows:
1. The distance may vary due to environmental conditions.
2. Always walk test the detector to confirm the detection distance.
Factory default
Factory default
a
c
b
d
3.0 m (10 ft.)
6.5 m (22 ft.)
3.0 m (10 ft.)
13 m (43 ft.)
18 m (60 ft.)
5.0 m 10 m
5.0 m
5.0 m
5.0 m
10 m
15 m
3.0 m (10 ft.)
3.0 m (10 ft.)
10 m (33 ft.)
MASK
MASK
MASK
MASK
Upper position: a, Lower position: Factory default
Upper position: a, Lower position: b
Upper position: c, Lower position: b
Upper position: c, Lower position: d
Use only the following combinations
for the flap settings.
24 m
(80 ft.)
c
a
b d
N.A.
N.A.
13 m
(43 ft.)
N.A.
N.A.
Factory
default
Factory
default
Lower
Upper
18 m
(60 ft.)
10 m
(33 ft.)
6.5 m
(22 ft.)
1
1
2
2
3
3 4
4
Long range settings3
1
23
4
Step
Detection area settings and walk test
- 8 -
NOTE
NOTE
NOTE
4
Step
Detection area settings and walk test
HOW TO DEACTIVATE THE SHORT RANGE DETECTION AREA
Remove the plate.
Insert the plate into the position determined by
the required masking distance until it clicks.
If any plate is not used, place it in
the storage position.
Be careful not to lose
the plates.
Plate 2
Plate fix position
indicator
Plate 1
* Plate 1 and 2 are identical.
a
b
d
g
i
h
j
C
a
b
g
i
C
a
b
g
i
C
a
b
g
i
C
To adjust the SHORT range of detection,
set the upper and lower plates follows:
Use the following table to determine the positions of the plates that set the required masked area.
PIR short range detection area deactivation
Use only the following combinations for
the plate settings.
g
i
j h
N.A.
N.A. N.A.
Not used
Not used
Factory
default
Lower
Upper
1
23
4
g
i
h
j
3.0 m (10 ft.)
24 m (80 ft.)
3.0 m (10 ft.)
24 m (80 ft.)
24 m (80 ft.)
24 m (80 ft.)
3.0 m (10 ft.)
3.0 m (10 ft.)
MASK
MASK
MASK
MASK Upper position: Not used, Lower position: j
Upper position: i, Lower position: j
Upper position: i, Lower position: h
Upper position: g, Lower position: h
1
2
3
4
5.0 m 10 m 20 m
5.0 m 10 m 20 m
5.0 m 10 m 20 m
5.0 m 10 m 20 m
N.A.
Short range settings
4
1
23
- 9 -
NOTE
NOTE
4
Step
Detection area settings and walk test
Default
DIP switch settings
4-4. Switch settings
1 2 3 4
ON
OFF ON
OFF ON
Standard Immunity
AND OR
H
M
L
High
Middle
Low
PIR sensitivity setting
Default
LED
Immunity
Future use
PIR Logic
4-3. Adjusting the vertical angle
For best performance, install detector parallel to the ground.
Decide the detection length. To change the detection length, adjust the flap and plate positions.
Refer to 4-1. for the details.
Perform walk test to ensure
detector is parallel to the ground.
* This description assumes the detection length to be 0 m (0 ft.) to 24 m (80 ft.).
3.0 m (10 ft.)
24 m (80 ft.)
If the detection length is
shorter than the intentional
(refer to 4-1
), change
the detector angle upwards.
If the detection length is
longer than the intentional
(refer to 4-1 ), change the
detector angle downwards.
If the detection length is enough
to the intentional (refer to 4-1 ),
the adjustment is complete.
1
2
2
2
2
- 10 -
Altri manuali per inSight INS-HX-80N
3
Indice
Altri manuali Optex Sensore di sicurezza
Optex
Optex FASTUS CD22-15 Series Manuale utente
Optex
Optex OA-FUNXION Manuale utente
Optex
Optex VX-402R Manuale utente
Optex
Optex REDWALL-V Guida
Optex
Optex FlipX Series Manuale utente
Optex
Optex Redwall LRP 180QH Istruzioni per il montaggio
Optex
Optex Boundary Gard BX-80N Manuale
Optex
Optex FMX-ST Manuale utente
Optex
Optex FTN-R Manuale utente
Optex
Optex RXC-DT-X5 Manuale utente
Optex
Optex Boundary Gard BX-80NR Manuale utente
Optex
Optex URX-P01 Manuale utente
Optex
Optex REDSCAN mini-Pro Series Manuale di servizio
Optex
Optex RXC-RST Manuale utente
Optex
Optex SL-100 TNR Manuale utente
Optex
Optex REDSCAN PRO RLS-50100V Manuale utente
Optex
Optex AX-70TN Manuale utente
Optex
Optex OVS-50TNR Manuale utente
Optex
Optex Smart Line Series Manuale utente
Optex
Optex HX-40 Manuale utente
