Optex VX Infinity Series Manuale utente
-1-
INSTALLATION INSTRUCTIONS
No.59-1936-1
VX InfinityTMseries
VX InfinityTMseries
CONTENTS
VXI-R Battery operated model with 2 PIR
VXI-RAM VXI-R with anti-masking
VXI-RDAM VXI-RAM with micro-wave
INTRODUCTION
1-1 BEFORE INSTALLATION
1-2 PARTS IDENTIFICATION
1-3 DETECTION AREA
INSTALLATION
2-1 WIRING DIAGRAM
2-2 R MODEL BATTERY BOX RBB-01 (OPTION)
2-3 TRANSMITTER PREPARATION
2-4 BEFORE MOUNTING
2-5 WALL TAMPER WRS-04 (OPTION)
2-6 MOUNTING
2-7 AREA ANGLE ADJUSTMENT
2-8 AREA MASKING
2-9 DETECTION LENGTH ADJUSTMENT
1
2
3
4
5
6
7
8
SWITCH SETTING
WALK TEST
LED INDICATION
BATTERY
6-1 HOW TO REPLACE BATTERY
6-2 BATTERY LIFE
SPECIFICATIONS
7-1 SPECIFICATIONS
7-2 DIMENSIONS
SETTING OF SPECIAL DETECTION AREA
2
3
4
4
4
5
5
5
6
7
7
8
9
11
12
13
13
14
14
15
BATTERY OPERATED MODEL
MULTI DIMENSIONAL OUTDOOR DETECTOR
MULTI DIMENSIONAL OUTDOOR DETECTOR
The VX InfinityTM series provide highly reliable detection functions, reducing false reports or
report losses. The VX InfinityTM series deliver stable detection performance even in severe
outdoor environments.
FEATURES
-12 m (40 ft.) by 90 degree flexible detection pattern adjustable to 5 ranges
- SMDA Logic for advanced temperature compensation and environmental noise immunity.
- Easy Masking for over spill prevention
- Double Conductive Shielding against bright light disturbance.
- Conduit/TX-Battery Case for both wired and wireless-ready models.
BASIC FEATURES
- Active IR Anti-Masking for detecting covering objects
- Tough Mod Dual Technology based on OPTEX gold-plated microwave module
- Super Low Energy Circuit for maximum Battery life expectancy
OPTIONAL FEATURES
-2-
INTRODUCTION
1
1-1 BEFORE INSTALLATION
Warning
Caution
Failure to follow the instructions provided with this indication and improper handling may cause
death or serious injury.
Failure to follow the instructions provided with this indication and improper handling may cause
injury and/or property damage.
The check mark indicates recommendation.
The nix sign indicates prohibition.
• Sunlight and reflection • Heat source • Objects moving in the wind
0.8 – 1.2 m
(2.64 – 3.94 ft)
Parallel
Do not remove the PCB. Keep product away from direct splash.
Mounting height. Keep the detector parallel to the
ground.
Consider the direction a person is
approaching from, as well as the
detection area.
Install the detector in a place where it is free from false alarm factors. For example:
Warning
Tilt
-3-
1-2 PARTS IDENTIFICATION
-Precautions for installing two or more sensors
Masking seal × 3 pcs
Screw kit
For wall mounting
Screw (4 × 20 mm)
Connector for POWER and ALARM
Cover unit
Main unit
Back box
Back box cap
Mounting plate
Connector for TROUBLE
1.0 m (3.28 ft) or more Less than 1.0 m (3.28 ft)
Velcro tape
VXI-R
VXI-RAM
VXI-RDAM
Do not install two or more VXI-RDAMs in side by side or face to face. Doing so may cause
malfunction. VXI-RDAM may be installed in back to back. If mounting on the same wall, make
sure that each unit is at least 1.0m (3.28 ft) apart from the other.
Optional accessories
Wall tamper (WRS-04)
-3-
Battery box (RBB-01)
-4-
INSTALLATION
2
1-3 DETECTION AREA
2-1 WIRING DIAGRAM
Trouble
Tamper
Alarm
Transmitter
<Overall wiring diagram>
Note>>
• The battery in the transmitter is shared with
the detector.
• Connection for TROUBLE is used when
monitoring for Tamper and Anti Mask.
Note>>
Be sure to insert the battery box all the
way until it clicks.
Transmitter side Main unit side
OPTION: WRS-04
Red
Black
White
Yellow
Red: Power input (+)
Black: Power input (-)
White: Alarm
Yellow: Alarm
Green: Trouble
Blue: Trouble
Brown: Tamper
Orange: Tamper
Gray: Tamper
Green
Blue
Brown
Orange
Gray
Mount the battery box inside the
back box as shown below.
Insert the battery box along the
groove of the back box.
Click!
Back box
Battery box
mounting space
12
a
b
c
d
e
fghi
j
l
m
n
k
TOP VIEW
SIDE VIEW
Length limiting position 1 (Default)
PIR
MW
Area diagram of horizontal position D
12m
12m 10m 12m10m5m 5m0
10m
5m
0
D
ABCEFG
1m
0 5m 10m 12m
Length limiting position 2
1m
0 5m 10m 12m
Length limiting position 3
1m
0 5m 10m 12m
Length limiting position 4
1m
0 5m 10m 12m
Length limiting position 5
1m
0 5m 10m 12m
Note>>
The maximum detection length may vary as
shown below due to environment conditions.
2-2 R MODEL BATTERY BOX RBB-01 (OPTION)
-5-
2-3 TRANSMITTER PREPARATION
2-4 BEFORE MOUNTING
<When monitoring ALARM and TROUBLE using the transmitter with 1 external input>
<To monitor only the ALARM using a transmitter
with 1 external input>
<To monitor the ALARM and TROUBLE using a
transmitter with 2 external inputs>
35 (1.38)
130 (5.12)
30 (1.18)
External input is N.C. External input is N.O.
3
... DIP switch 3: OFF (N.C.)
3
... DIP switch 3: ON (N.O.)
Connectors to be used
Connector for POWER and ALARM
Connector for TROUBLE
Red Black
How to position a battery
Connector for POWER
and ALARM
Connector for
TROUBLE
Connector for
POWER and ALARM
N.C. N.O.
Unit: mm (inch)
The transmitter used should have the internal dimensions of H 150 × W 34 × D 33 mm(H 5.91 × W 1.34 × D 1.30 inch)
or H 112 × W 55 × D 35 mm.(H 4.41 × W 2.17 × D 1.38 inch)
WRS-04 (option) Store the connecting
cable in a trench
and seal with a label
already in place.
Remove the cap.
1Open the cover unit.
2Remove the main unit from
the back box.
3Remove the back box
from the mounting plate.
4
Mount the wall tamper
(WRS-04) on the back
of the main unit.
1Run the wire along
the wiring groove.
2
2-5 WALL TAMPER WRS-04 (OPTION)
-6-
2-6 MOUNTING
Wall mount Pole mount
Metal band
Velcro tape
Transmitter
Transmitter side Main unit side
Red
Black
White
Yellow
Red: Power input (+)
Black: Power input (-)
White: Alarm
Yellow: Alarm
Green: Trouble
Blue: Trouble
Green
Blue
Note>>
• The battery in the transmitter is shared with the detector.
• Connection for TROUBLE is used when monitoring for
Tamper and Anti Mask.
* Use a metal band with
25 mm or less in width.
Put the top of the back
box on the hook.
1.
2.
3.
1Mount the mounting plate. 2Mount the back box on the mounting plate.
3Mount the transmitter on the back of the main unit. 4Connect the connectors
5Mount the main unit to the back box. 6Put the cap on top.
-7-
2-7 AREA ANGLE ADJUSTMENT
2-8 AREA MASKING
Horizontal position D
(Default)
Horizontal position B
(F: symmetrical
position)
Horizontal position C
(E: symmetrical
position)
Horizontal position A
(G: symmetrical
position)
D
ABCEFGD
ABCEFG
D
ABCEFG
D
ABCEFG
D
ABCEFG
D
ABCEFG
D
ABCEFG
or
or
or
Note>>
When creating a special detection area, refer to the end of this manual.
If there is an unwanted object within the detection area, apply an area masking label to the appropriate area.
Insert the protruding
part of the cover into
the lens hole.
Fit the edge of the
lens.
Slide the lens holder to secure it.
Unwanted
object (Tree)
3Insert the lens into the cover. 4Mount the lens holder to the cover.
The angle can be adjusted in
7 levels from A to G.
The detection area becomes
14 zones only when A or G is
selected.
1Slide the lens holder and remove the lens holder out
of the cover as shown below. 2Identify positions to mask on the lens and apply a
corresponding strip from the masking sheet 1.
-8-
2-9 DETECTION LENGTH ADJUSTMENT
MW sensitivity
adjustment
Both upper and lower detection
area are blocked
IMPORTANT
BOTH DETECTION AREAS MUST BE
BLOCKED FOR DETECTION
Detection!
NO
Detection
NO
Detection
Only upper detection area is blocked
Only lower detection area is blocked
1Adjust the PIR detection length by sliding the lower
PIR to the desired position.
2Adjust the MW detection length by rotating the MW
sensitivity adjustment according to the PIR area.
Detection length setting chart
* The detection lengths described above should be used as a guideline.
Position
1
(Factory
default)
2
3
4
5
12.0 m
(40.0 ft)
8.5 m
(27.9 ft)
6.0 m
(19.7 ft)
3.5 m
(11.5 ft)
2.5 m
(8.2 ft)
10.0 -17.0 m
(32.1 - 55.8 ft)
7.0 - 12.0 m
(23.0 - 39.4 ft)
5.0 - 8.5 m
(16.4 - 27.9 ft)
3.0 - 6.0 m
(9.8 - 19.7 ft)
2.0 - 3.5 m
(6.6 - 11.5 ft)
Max detection length Detection area
MW
sensitivity
adjustment
12 m
8.5 m
6 m
3.5 m
2.5 m
-9-
NORM ⇔TEST
DIP switch 1
DIP switch 2
SWITCH SETTING
3
-WALK TEST MODE
VXI-R
VXI-RAM
VXI-RDAM
ON
123456
POSITION FUNCTION
TEST
(Factory default)
NORM
The LED lights irrespective of the DIP switch 4 (LED)
setting.
The DIP switch 2 (BATTERY SAVING TIMER) setting is
inactive.
The LED lights depending on the DIP switch 4 (LED)
setting.
The DIP switch 2 (BATTERY SAVING TIMER) setting is
active.
Caution>>
After completing a walk test, always set the unit to NORM position for operation.
Using the unit in TEST mode will shorten the battery life.
120S ⇔5S
-BATTERY SAVING TIMER
VXI-R
VXI-RAM
VXI-RDAM
ON
123456
POSITION FUNCTION
5S
120S
(Factory default)
5 sec.
120 sec.
Even if there are continuous alarm events, the alarm is generated only once
in the timer period to save the battery life.
PIR sensitivity selector
DIP switch
1 WALK TEST MODE
2 BATTERY SAVING TIMER
3 ALARM & TROUBLE OUTPUT
4 LED
5 ANTI-MASKING
6 MICROWAVE IMMUNITY
1
ON
2 4 5 63
MW sensitivity adjustment
-10-
DIP switch 3
N.C. ⇔N.O.
-ALARM & TROUBLE OUTPUT
VXI-R
VXI-RAM
VXI-RDAM
ON
123456
POSITION FUNCTION
N.O.
N.C.
(Factory default)
N.O. output
N.C. output
DIP switch 4
OFF ⇔ON
-LED
VXI-R
VXI-RAM
VXI-RDAM
ON
123456
POSITION FUNCTION
ON
OFF
(Factory default)
LED ON
LED OFF
Note>>
If the LED lights, check the DIP switch 1 (WALK TEST
MODE) setting.
DIP switch 5
OFF ⇔ON
-ANTI-MASKING
VXI-R
VXI-RAM
VXI-RDAM
ON
123456
POSITION FUNCTION
OFF
ON
(Factory default) ANTI-MASKING ON
ANTI-MASKING OFF
When masking condition continues more than 3 minutes, TROUBLE will be generated.
TROUBLE is generated after 20 seconds under the anti-masking test mode.
Teaching mode starts when both the separate box cover and the main unit cover are
attached.
Please be careful not to leave any object within 1 m from the unit.
<ANTI-MASKING function>
ANTI-MASKING test mode
The trouble is output after 20 seconds.
Normal mode
The trouble is output after 3 minutes.
10 minutes1 minute
Teaching
Altri manuali per VX Infinity Series
1
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali Optex Sensore di sicurezza
Optex
Optex HX-80N Manuale utente
Optex
Optex FASTUS CD22-15 Series Manuale utente
Optex
Optex Boundary Gard BX-80N Manuale
Optex
Optex REDBEAM Series Guida rapida
Optex
Optex HX-80NRAM Manuale utente
Optex
Optex FTN-R Manuale utente
Optex
Optex AX-70TN Manuale utente
Optex
Optex VX SHIELD Series Manuale utente
Optex
Optex CX-702RS Manuale utente
Optex
Optex RXC-DT-X5 Manuale utente
Optex
Optex BX SHIELD Series Manuale utente
Optex
Optex CX-702S Manuale utente
Optex
Optex MX-40QZ Guida rapida
Optex
Optex CX-702 MKII Manuale utente
Optex
Optex OVS-50TNR Manuale utente
Optex
Optex BX SHIELD Series Manuale utente
Optex
Optex PRO SWING OA-EDGE1 T Manuale utente
Optex
Optex AX-70TN Manuale utente
Optex
Optex FTN-RRHW Manuale utente
Optex
Optex CX-702 MKII Manuale utente
