Optimus 4-Inch Flush-Mount Speaker System Istruzioni operative

Optimus 4-Inch Flush-Mount Speaker System

(120-1746) Preparation Faxback Doc. # 34216

CHOOSING A LOCATION

For the best performance, install these speakers on a solid, firm surface

that does not vibrate at high volume levels. We recommend you mount the

speakers in the door panels or the rear deck.

NOTE: Cardboard or fiber panels are not good mounting surfaces.

As you are deciding on a location, carefully inspect the area behind the

proposed mounting surface.

There must be a clear unobstructed area of at least 2 inches (50.8 mm)

behind the panel.

If it is a door location, check to be sure the window, window mechanism

and window handle will clear the speaker.

NOTE: Make sure the window opens and closes properly.

Optimus 4-Inch Flush-Mount Speaker System

(120-1746) Installation Faxback Doc. # 34217

INSTALLING THE SPEAKERS

1. Use the supplied template to mark the speaker opening and the mounting

screw hole locations.

2. Cut out the marked speaker opening in the mounting surface.

NOTE: Steel door panels and the rear deck (behind the upholstery)

might already have large cut-out areas for recessing the speaker

3. Drill the four mounting-screw holes.

CAUTION: Be careful not to drill into anything behind the mounting

surface.

4. Mount the supplied speed clips directly onto the mounting screw holes

that you drilled using the supplied template.

5. If necessary, route new speaker wire from the autosound system to the

mounting area.

CAUTIONS: Avoid routing speaker wire where it can be pinched or

stepped on. You can usually route it along the channel

beneath the vehicle's door facings.

If you selected door locations, you might need to punch a

small hole in the door edge (near the door hinges) to route

the wires into the door. Leave enough slack wire to open the

door all the way.

6. Insert the positive (+) and negative (-) stripped speaker wire ends

through the corresponding speaker terminals, wrap them around the

terminals, and either solder or crimp them in place.

CAUTIONS: Improper phasing can cause poor bass response. To ensure

proper phasing, you need to match your autosound system's

positive (+) and negative (-) speaker wires to the corres-

ponding positive (+) and negative (-) speaker terminals.

Do not connect any of your speaker terminals to chassis

ground.

7. Remove the grille from each speaker's mounting bracket to expose the

mounting holes.

8. Place the mounting bracket on the speaker.

9. Align each speaker's mounting holes and the mounting bracket's holes

with the holes on the speed clips, thread a supplied screw through each

mounting hole, and tighten all screws until they are secure.

10. Firmly press the grille onto each speaker's mounting bracket.

NOTE: You can use the supplied adhesive glue to further secure the

grille to the mounting bracket.

Press the glue into the mounting bracket's edges.

Optimus 4-Inch Flush-Mount Speaker System

(120-1746) Specification Faxback Doc. # 34218

Speaker Size:

Woofer: ........................................ 4 Inch (102 mm) Dual Cone

Woofer, Cone: ...................................................... Paper

Sub Cone: .......................................................... Paper

Grille: ...................................................... Hi Heat ABS

S.P.L.: ............................................................ 89 dB

Barium Magnet Weight: ...................... 70 x 32 x 10, 5.4 oz (1/8 kg)

Maximum Power: .......................................... 45 Watts/Channel

Power Handling: ..................................... 15 Watts RMS/Channel

Impedance: ........................................................ 4 Ohms

Frequency Response: ....................................... 95 Hz - 19 kHz

Weight (one speaker): ................................... 1 lb. (0.453 kg)

Dimensions (HWD): ...................... 4 13/16 x 4 13/16 x 2 5/16 Inches

(122 x 122 x 59 mm)

Specifications are typical; individual units might vary. Specifications

are subject to change and improvement without notice.

(YO/EB 7/29/96)

LN-03/04

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Optimus Sistema di altoparlanti

Optimus

Optimus STS 150 Manuale utente

Optimus

Optimus SWS-250 Manuale utente

Optimus

Optimus STS 200 Manuale utente

Optimus

Optimus PRO CS-5 Manuale utente

Optimus

Optimus PRO SWS-502 Manuale utente

Optimus

Optimus AMX 2 Manuale utente

Optimus

Optimus OPTIMUS PRO-SWS300 Manuale utente

Optimus

Optimus 40-1425 Manuale utente

Optimus

Optimus SYSTEM 741 Manuale utente

Optimus

Optimus AMX-4 Manuale utente

Optimus

Optimus XTS 20AV Manuale utente

Optimus

Optimus 61/2-Inch 3-Way Flush Mount Speaker System Manuale utente

Manuali Sistema di altoparlanti popolari di altre marche

JVC

JVC CA-MXK5R Manuale utente

LG NB4532B Manuale utente

JVC

JVC CA-FSH100 Manuale utente

5Core

5Core Pro Series Manuale utente

EAW

EAW MQV1394e Manuale utente

Lynx

Lynx GXR-LA10A Manuale utente

iLive

iLive ITB066B Manuale utente

RDX

RDX QuickStation 4 Manuale utente

Electro-Voice

Electro-Voice S-122 Manuale utente

Sven

Sven SPS-619 GOLD Manuale utente

Pioneer

Pioneer CS-7070 Manuale utente

EAW

EAW UB82e Manuale utente

Sondpex

Sondpex Active Speaker System and Digital Music... Manuale utente

JVC

JVC NX-PN7 Manuale utente

Marshall Amplification

Marshall Amplification AR-DM61-BT Manuale utente

Yamaha

Yamaha NX-A01 - Speaker Sys Manuale utente

SE Audiotechnik

SE Audiotechnik I-LINE Manuale utente

Gemini

Gemini WRX-843 Series Manuale utente