OPTIX SVC600 Manuale utente
QUALITY PRODUCTS FOR THE PROFESSIONAL INSTALLER
SIDE / REAR VIEW
Camera
MODEL : SVC600
Table of Contents
INTRODUCTION 3
Contents/Device
FENDER MOUNT 4
MOUNTING PLATE 5
BOTTOM MOUNT 6
QUICK START/INSTALLATION 7
MODEL : SVC600
INTRODUCTION
Congratulaons on your purchase of the Opx “Side/Rear View Camera Kit”. These cameras can be
used in a number of dierent conguraons. When connected to a screen as side view cameras, you can
safely monitor the sides of the vehicle and blind spot areas that are hard to see. These cameras are fully
adjustable and can be used as either side mount or boom mount by opening up the shroud and chang-
ing the posion on the camera. Reverse camera opon is also available with the boom mount opon, but
only one camera is used with this applicaon.
Contents
2 - Side view camera’s 2 - Din to video cable’s
2 - Boom mount adapter’s 2 - Video and power cable’s
2 - Boom mount adapter’s
2 - 3M double sided adhesive tape
MODEL : SVC600
Device
Camera Boom mount 3M double sided
adhesive
Loop(cut for mirror image o)
Le/Right idener
Fender mount
Type 1: Fender Mount
1. Inspect the area for suitable mounng locaon (make sure camera cable is clear of
any moving parts) We recommend tesng the locaon for opmum viewing angle be-
fore permanently mounng camera.(See example below)
2. Use the pre-installed fender shroud on camera to mount.
3. Clean the surface on vehicle and camera to get rid of any oils or dirt (adhesion pro-
moter recommended).
4. Using the appropriate camera (le or right) apply the 3M adhesive tape to camera
and secure to vehicle.
5. Route the cables through the vehicle and connect to monitor.
6. Repeat steps 1-5 for other side.
FENDER MOUNT
MODEL : SVC600
Accele Electronics will not be responsible for damages caused to your vehicle
due to improper installaon.
Accele Electronics will not be responsible for damages caused to your
vehicle due to improper installaon.
MODEL : SVC600
Type 2: Boom Mount (Adapng the camera)
MOUNTING PLATE
STEP 1 - REMOVE 3 SCREWS STEP 2 - REMOVE WIRE SCREW STEP 3 -
A. MARK AND NOTE THE TOP OF
CAMERA
B. ROTATE CAMERA COUNTER
CLOCKWISE
90 DEGREES (1/4 TURN)
C. PLACE CAMERA BACK IN HOUSING
STEP 4 - INSERT CABLE
STEP 5 - REASSEMBLE 3 SCREWS STEP 6 - CLEAN AND AFFIX 3M TAPE
MODEL : SVC600
Type 2: Boom Mount
1. Inspect the area for suitable mounng locaon (make sure camera cable is clear of any moving
parts) We recommend tesng the locaon for opmum viewing angle before permanently mount-
ing camera. (See example below)
2. If doing under the mirrors, route the wires into the door and zip e on to exisng harnesses. The
wires should be routed from the door to the inside of the vehicle through the factory door harness.
3. Switch the camera mount as per instrucon on page 5 In Owners manual.
4. Drill a 1/4” hole in mounng area
5. Clean the surface on vehicle and camera to get rid of any oils or dirt (adhesion promoter recom-
mended).
6. Using the appropriate camera (le or right) apply 3M adhesive tape to camera. Run cable
through 3M adhesive pad and mounng hole then connect to wire ran in step 2.
7. Peel back the adhesive cover and mount the camera to the vehicle . (Point camera at 45 degrees
for best viewing angle)
QUICK START/INSTALLATION
Accele Electronics will not be responsible for damages caused to your ve-
hicle due to improper installaon. For complete owners manual please visit
hps://accele.com/technical-support-ii/svc600 Thank you for being a
valued customer of ACCELE ELECTRONICS
Indice
Altri manuali OPTIX Macchina fotografica digitale
