ORBRY Smart Touch Manuale utente

Smart Touch

Thermostat

Colour

Touchscreen

Thermostat

OBSMART

DO DO NOT

Install a conduit for your

sensor probe before thermo-

stat installation.

Ignore electrical regulations.

Install this thermostat in

a wet zone.

The Orbry Smart Touch Thermostat is IP30 rated and suitable for

safe installation in bathrooms. It is not suitable for use in special lo-

cations, such as wet zones. All electrical circuits in bathrooms must

be protected by a 30mA RCD. The instructions we supply include as

much information as possible to ensure that all installations comply

with current electrical regulations. Please call our customer support

line, if in any doubt, on 0845 208 0221.

The Orbry Smart Touch Thermostat is a digital thermostat, which is

designed for electric underoor heating systems with a maximum

load of up to 16A (3600W). The Orbry Smart Touch features a 4.3”

colour touchscreen display and four (4) languages.

ALL WIRING MUST CONFORM TO

IEE 17TH EDITION PART P REGULATIONS.

THIS PRODUCT IS RATED IP30.

Orbry Smart Touch Thermostat

INTRODUCTION

IMPORTANT SAFETY REGULATIONS

Place the unit face down on a hard surface and push the three (3)

clips located on the bottom of the Orbry Smart Touch in with

a screwdriver to release the face plate.

Once the face plate has been gently opened disconnect the ribbon

cable to release the face plate.

Step 1: Release the face plate

Step 2: Disconnect ribbon cable & remove face plate

The sensor conduit and deep back box must be  tted before

installation of the actual thermostat can begin. Feed the sensor

probe provided down through the sensor conduit into

a representive area of the  oor. For technical advice or help with

any queries, please call our customer support team

on 0845 208 0221 or visit www.orbry.com/orbry-downloads.

Before you begin

Installation

INSTALLING THE ORBRY SMART TOUCH

1. 4.

2. 5.

Fix the Orbry Smart Touch Thermostat to the wall

Align the Orbry

Smart Touch with

your back box and

 x in place with the

screws provided.

Now, reconnect the

ribbon connections

and reseat the face

plate (bottom edge

 rst). Ensure the

Orbry Smart Touch

is securely  xed

before continuing.

Faceplate

Provided screws

Ribbon connectors

Back plate

Back box

Wire and replace the face plate

Sensor

7 6 4 3 2 15

3600W/16A

230V/AC

Loosen the tension

screws to allow the

wires to be inserted

and  xed. Position

the cables as shown

in the wiring diagram

and ensure each

screw is tightened

correctly.

Ensure system is correctly earthed.

WIRING THE ORBRY SMART TOUCH

Heating icon

Menu button Ambient temperature

Up button Temperature icon

Mode button Weekday icon

Down button Clock icon

Mode icon

Set temperature

Floor temperature

Mode icon area

ROOM

1. 8.

2. 9.

3. 10.

4. 11.

5. 12.

6. 13.

7. 14.

10 9 8 7 6

Orbry Smart Touch Thermostat Interface

On / O button

Back plate

PROGRAMMING THE ORBRY SMART TOUCH

Preset Modes

Settings

Language selection – Press to choose one of four (4) languages.

Economy mode – Preset a low energy saving temperature

18°C for economical comfort and energy savings.

Comfort mode – Preset a comfort temperature (e.g. 25°C)

and enjoy warmth outside of your heating schedule.

Program mode – Your own customisable heating schedule.

Holiday mode – Automatically maintain a preset low energy

saving temperature (e.g. 8°C) while you’re away.

Boost mode – Set a high temperature (e.g. 27°C) and quickly

switch to this high temperature on demand.

Preset temperatures – Use to dene pre-set temperatures.

Program review – Use to check your 5+1+1 day schedule.

Date & time button – Use to set the correct weekday and time.

Protection temperatures – Use to dene minimum and

maximum temperatures.

Manually switch between these preset temperature modes to allow

exibility outside of your heating schedule.

PROGRAMMING THE ORBRY SMART TOUCH

Press the MENU Button, then

press

to review your weekly

schedule.

Select Mon – Fri, Sat or Sun

to edit your custom heating

schedule.

Example: If you would like to

edit your Sunday schedule,

then press the Sun column to

enter the edit page (as shown).

Every setting can be edited

using the or buttons.

In the Sun column, there are six (6) periods. You can press

the or buttons to choose the period you are going to

change. The button will display beside the period selected.

Finally, press APPLY to save your new schedule.

Next, you can set the start time and desired temperature by

pressing the and buttons.

Schedule settings

Language selection – Press to choose one of four (4) languages.

RETURN

PROGRAMMING THE ORBRY SMART TOUCH

Press the MENU button, then

the

button to edit the date

and time with the and

buttons. Press APPLY to save

the changes.

Press the MENU button, then

the

button to select a mode.

Now, edit that mode setting’s

temperature using the and

buttons. Press APPLY to save

the changes.

Press the MENU button, then

the

button to enter the

language page. Choose the

desired language and press

APPLY to save the changes.

Edit date & time

Preset temperature

mode

Language select

PROGRAMMING THE ORBRY SMART TOUCH

RETURN

Press the MENU then the

button to enter the protection

settings page. You can set an over

protection temperature and a low

protection temperature using the

and buttons. Press APPLY

to save the changes.

Protection settings

High protection: This is an over heat protection setting designed

to monitor the oor temperature and set a limit dened by you.

If the system reaches the set protection temperature, the system

will shut o automatically.

Low protection: This is a frost protection mode designed to

function when the Orbry Smart Touch is switched o. If the ambient

temperature reaches the set protection temperature, the system

will automatically switch on to maintain a minimum temperature.

Please note: The upper limit should be no higher than 28°C

to conform with European regulations.

PROGRAMMING THE ORBRY SMART TOUCH

RETURN

Parameter settings

To access the parameter settings, switch the Orbry Smart Touch

OFF and immediately press the

button for two (2) seconds. You

can set the desired values by pressing << OR >>. Go to the other pag-

es by pressing PRE or NEXT. The upper limit should not exceed 28°C.

PROGRAMMING THE ORBRY SMART TOUCH

01 -8°C ~ 8°C

Temperature Offset

03 5°C ~ 35°CSet Point Maximum

05 I only, E only,

I & E, I or E

NTC Select (Ambient – I, Floor – E)

07 5°C ~ 10°C

Low Protection Minimum

09 5°C ~ 90°CHigh Protection Minimum

11 1% ~ 100%Min. Backlight Brightness of Standby Status

13 Normal (NO);

Inverted (NC)

Relay Output

02 0°C ~ 3°CDead Zone

04 5°C ~ 35°C

Set Point Minimum

06 5°C ~ 10°C

Low Protection Maximum

08 5°C ~ 90°C

High Protection Maximum

10 3s ~ 180sBacklight off Time after Operation

12 0s ~ 250s

Relay Delay Time

14 << or >>

Restore

Description Range

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali ORBRY Termostato

ORBRY

ORBRY OBUHTOUCH Guida rapida

Manuali Termostato popolari di altre marche

EWELLY

EWELLY EW-181 Manuale utente

Prolon

Prolon T1100 Istruzioni per l'installazione

Computherm

Computherm Q20 Manuale utente

Heatmiser

Heatmiser neoStat Manuale utente

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuale utente

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuale utente

Saswell

Saswell SAS920XWHB-7-S-RF Guida

Aircalo

Aircalo TFP1-ET85P2 Manuale utente

Honeywell

Honeywell CM721 Manuale utente

Carrier

Carrier DEBONAIR 33CS Manuale utente

Lennox

Lennox iHarmony Zone Thermostat Istruzioni per il montaggio

Gemtech

Gemtech GT7000 Manuale di istruzioni

Rollei

Rollei Smartes 45000 Manuale utente

Sinope

Sinope TH1300RF Manuale utente

Honeywell

Honeywell RLV4305 Manuale utente

Honeywell

Honeywell Prestige 2.0 THX9421 Manuale utente

NuTone

NuTone NTBZ48 Istruzioni operative originali

Stelpro

Stelpro MAESTRO ASMT402AD Manuale utente