OrthoDuad ES400 Manuale utente
USER’S MANUAL MOBILITY SCOOTER - ES400 / ES500
WARNING
Read the User Manual carefully before operating the ES400/ES500.
If you do not fully understand any part of this manual, please contact your dealer or
any of our Service Centres.
Read this manual step by step, as injury or damage may occur from misuse!
WARNING
Electromagnetic Interference (“EMI”) can cause powered vehicles to behave
erratically, which could be dangerous to the user.
For your safety and protection, it is IMPERATIVE that you take time to read
Chapter V (“EMI WARNING”) before operating the ES400/ES500.
TABLE OF CONTENTS
I.
Introduction
3
II.
Specifications
4
III.
Features
5
IV.
Operating your scooter
6
V.
Safety Instructions
9
VI.
Battery Charging
14
VII.
Maintenance Schedule
15
VIII.
Warranty
16
I. INTRODUCTION
Thank you for choosing Orthoquad ES400/ES500
mobility scooter. This scooter is a mobility assistive device
designed for senior citizens who have walking difficulty or
are weak in physical strength and for also for the disabled
people.
We designed this scooter to restore your personal
freedom, to provide convenience and comfort to you.
This manual contains important information
concerning the safe operation and proper maintenance of
your scooters.
Your ES400 has many unique features not found on
other scooters. With proper care and maintenance, you
should enjoy many years of dependable service from your
unit.
Your scooter should receive regular maintenance
according to the schedule outlined in this manual, and the
recommendation from the authorized dealer. By following
the maintenance instructions, you will be able to take care
of most of your unit’s needs.
Above all, follow all service recommendation
outlined in this manual to achieve the most trouble free,
safe and enjoyable operation of your scooter.
II. SPECIFICATIONS
ES400/ES500
PERFORMANCE DATA
Maximum forward speed 12 km/h
Maximum Climbing Grade 6° -10.5%
Load Capacity 120kg - 265 pounds
Ground Clearance 6 cm
Range with Full Charge Up to 40km
Turning Radius 1.2m
DIMENSIONS
Length 51’’
Width 25’’
WEIGHT
Total (with battery) 98kg – 215lbs
BATTERY SPECIFICATIONS
12V/38 Ah Lead-acid battery
BATTERY CHARGER
Input AC /110V/60Hz Output DC24V/ 5amp
MOTOR POWER ES400: 400W / ES500: 450W
III. FEATURES
Swing away armrests
360 degrees swivel seat
Adjustable Forward/Reverse Seat
Adjustable tiller
Dynamic regenerative braking
Rear wheel direct drive with differential
Fully solid state controller
External Battery Charger
24-volt permanent magnet heavy duty DC motor
ON/OFF switch lock
Horn
LED Head light
Turning lights
Rear lights
Battery-charging indicator
Anti-tip-off safety wheels
Front and rear bumpers
Accessories adapter
Electronic High/Low speed switch
IV. OPERATING YOUR SCOOTER
The photo below shows the operating controls of your
mobility scooter.
Battery status
indicator
Throttle control lever
Throttle control lever
Horn
Horn
Turning lights
switch
Key Switch
Charger socket
High/Low speed mode
switch
Headlight switch
Speed limit dial
1, BEFORE OPERATION
1). Insert the power key into the switch lock and turn clockwise to the
ON position.
2). Check the battery charge indicator to make sure the batteries are
fully charged.
3). Make sure that clutch lever is at close position.
2, TURN POWER ON
Insert the key into the key switch on the upper tiller and rotate
clockwise to the “ON” position.
3, FORWARD MOTION
To move forward, pull the right thumb lever under the control
console forward. The further you pull, the faster the scooter will go.
The maximum speed may be selected by the speed selection switch
located on the top of the control console.
3. REVERSE MOTION
To reverse, pull the left side of the thumb lever under the control
console forward.
4. STOP
To stop the scooter, just release the thumb lever. The scooter will
quietly come to a smooth stop and electromechanical brake will
automatically engage to hold the scooter in position on horizontal
surface or an incline of up to 12 degrees, with a load of no more than
265 lb. (120 kg). Quick smooth stops are made possible by the
dynamic braking feature built in the controller.
WARNING
The brake may not be effective when engaged on inclines greater
than 15 degrees or 21% if the occupant’s weight exceeds 265
pounds.
TEST DRIVE
Insert the ignition key into the main switch.
Check the battery charge indicator to ensure that
the batteries are fully charged.
Make sure the clutch lever is engaged.
Set the speed by turning the dial knob on top of the
console.
Go back and forth a short distance to make sure
your unit is in good working condition.
FREEWHEEL MODE
Your ES400/ES500 is equipped with a manual freewheel lever that,
when pushed forward, allows the ES400/ES500 to be pushed
manually.
Disengage the drive motors only on a level surface.
Stand beside the ES400/ES500 to engage or disengage freewheel mode.
Never do this while sitting on the ES400/ES500.
After you have finished pushing your ES400/ES500, always return it to the
drive mode to lock the brakes (pull the manual freewheel lever backward).
When using the freewheel lever, be careful not to touch the internal
surface of the motor, as it could be very hot and cause injury. See the
warning label at the rear of the scooter near the lever.
Freewheel Manual lever
V. SAFETY INSTRUCTIONS
Your scooter can move on grass , gravel, dirt, and sand surfaces, as
well as hard paved or carpeted surfaces. However, extra caution
should be taken when operating your unit on uneven surfaces other
than flat surfaces.
Slow the scooter when approaching an uneven or soft surface.
Avoid gravel and sand.
Avoid stop your scooter in the middle of a slope too steep. If you have to,
start up again slowly and then accelerate cautiously.
Inspect the following points before setting off:
• Check tire pressure (40-45 psi)
• Check electrical connections.
• Check the brakes
• Check the battery charge.
CAUTION:
IT IS VERY IMPORTANT THAT YOU READ THIS
INFORMATION REGARDING THE POSSIBLE EFFECTS OF
ELECTROMAGNETIC INTERFERENCE ON YOUR
POWERED SCOOTER.
Electromagnetic Interference (EMI) From Radio Wave Sources
Powered wheelchairs and motorized scooters (in this text, both
will be referred to as powered wheelchairs) may be susceptible to
electromagnetic interference (EMI), which is interfering
electromagnetic energy (EM) emitted from sources such as radio
stations, TV stations, amateur radio (HAM) transmitters, two-way
radios, and cellular phones. The interference (from radio wave
sources) can cause the powered wheelchair to release its brakes, move
by itself, or move in unintended directions. It can also permanently
damage the powered wheelchair’s control system. The intensity of
the interfering EM energy can be measured in volts per meter (v/m).
Each powered wheelchair can resist EMI up to certain intensity. This
is called its “immunity lever.” The higher the immunity level, the
greater the protection. At this time, current technology is capable of
achieving at least a 20-v/m immunity level, which would provide
useful protection from the more common sources of radiated EMI.
The immunity level of this powered scooter as shipped, with no
further modification, is not known.
There are ample sources of relatively intense electromagnetic
fields in the everyday environment. Some of these sources are
obvious and easy to avoid. Others are not apparent and exposure is
unavoidable. However, we believe that by following the warnings
listed below, your risk to EMI will be minimized.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali OrthoDuad Scooter
