OSD Audio Sounsole 2.1 Manuale utente

Desk-Top/Table-Top All in One Sound System

OSD Audio · 775 Columbia Street · Brea, CA 92821 · Tel: (562) 697-2600 · www.osdaudio.com Page 1

OSD Audio · 775 Columbia Street · Brea, CA 92821 · Tel: (562) 697-2600 · www.osdaudio.com Page 2

OSD Audio · 775 Columbia Street · Brea, CA 92821 · Tel: (562) 697-2600 · www.osdaudio.com Page 3

Includes

1 - Stereo SoundSole 2.1

1 - IR Remote Control

1 - Lithium Battery (3V, CR2025)

1 - Stereo RCA Patch Cable

1 - Digital Optical Patch Cable

1 - AC Power Supply

OSD Audio · 775 Columbia Street · Brea, CA 92821 · Tel: (562) 697-2600 · www.osdaudio.com Page 4

Congratulations and thank you for purchasing OSD AUDIO SOUNDSOLE 2.1 Desk/Table-Top All in One System.

The OSD AUDIO SOUNDSOLE 2.1 greatly enhances the sound quality of today’s flat screen LED, LCD and Plasma

TVs without having to add a lot of speakers. A single speaker system that requires very little space, the SOUNDSOLE

2.1 can be installed below or in front of a high definition TV or inside a cabinet. You’ll enjoy simulated surround sound

from a single, space- saving cabinet with deep, enveloping bass without bulky speakers or amps. The OSD AUDIO

SOUNDSOLE 2.1 easily connects to inputs on today’s flat panel TVs and digital music players and even syncs to

almost any Bluetooth audio device.

OSD Audio

SOUND SOLE 2.1

FRONT PANEL

1. STATUS LED - (Behind front panel lens.) One multi-color LED. This LED will illuminate red/blue and flash in

different modes to indicate changes in the SOUNDSOLE 2.1operational status. SOLID RED - OFF (Standby).

Power cord is connected and AC switch is turned ON, but the SOUNDSOLE 2.1 is OFF.

SOLID BLUE –ON –OSD AUDIO SOUNDSOLE 2.1 is ON.

SINGLE BLUE FLASH - Confirms receiving an IR command from the OSD AUDIO SOUNDSOLE 2.1

Remote for changes to Treble/Bass, EQ Reset, Simulated Surround (SR), single Volume UP/DOWN

command, initiating output of the Bluetooth Connection Code.

RAPID BLUE FLASH - Confirms receiving a continuous IR stream from the SOUNDSOLE 2.1 Remote

for ramping volume UP/DOWN. Rapid blue flash also indicates the SOUNDSOLE 2.1 is in Bluetooth

pairing mode.

SLOW BLUE FLASH - Audio Mute. Audio signal to the speakers is turned OFF.

TWO BLUE FLASHES; DELAY - Bluetooth input is selected and no Bluetooth device is connected or it is

out of range.

2. IR SENSOR - (Behind front panel lens.) The IR Sensor ‘sees’ the IR control commands output from the

SOUNDSOLE 2.1 IR Remote Control when buttons are pressed on the remote for armchair control of the

SOUNDSOLE 2.1. This sensor must be unobstructed for direct line-of-sight to the remote, or the remote will not

be able to control the SOUNDSOLE 2.1.

Page 5

OSD Audio · 775 Columbia Street · Brea, CA 92821 · Tel: (562) 697-2600 · www.osdaudio.com

DIGITAL FIBER OPTIC INPUT - One Digital Fiber Optic port. Connect to the Digital Optical OUT on a TV or other Digital

source. This input is selected by pressing the Source button on the OSD AUDIO SOUNDSOLE 2.1 IR Remote.

NOTE: The audio output of a TV, Blu-ray Disc player, game console, or DVD player connected to the SOUNDSOLE 2.1

via Coaxial Digital must be set to PCM in the source’s setup. Please see the device’s Owner’s Manual for details.

RCA ANALOG STEREO AUDIO INPUT - Two RCA jacks. Connect to the L & R Line Level Audio OUT on a TV or

other source. This input is selected by pressing the AUX button on the OSD AUDIO SOUNDSOL 2.1 IR Remote.

AC INPUT- Universal power connector. Automatically

selects AC voltage for a given region. Connect to the

included 2-conductor AC Power Cord. After all audio

connections have been made and confirmed, plug the

power cord into an un-switched AC Outlet to power the

OSD AUDIO SOUNDSOLE 2.1.

DOWN FIRING SUBWOOFER - The OSD AUDIO SOUNDSOLE 2.1 bottom panel features two 5-1/4” subwoofers,

one of the Drivers is active driven by a 30 Watt Low Pass Digital Class D Amplifier. The second 5.25” driver is a

Passive radiator helping to tune the enclosure. When handling the SOUNDSOLE 2.1 be careful not to grab or hold

the cabinet bottom where the woofers are located to prevent damaging the woofers. Also take care to not set the

cabinet down on anything but a flat surface clear of obstructions.

When placing the OSD AUDIO

SOUNDSOLE 2.1 PLATFORM on a shelf

or stand, be sure there are no objects

under the cabinet that will damage or block

the woofers and check to make sure there

are no objects on the sides of the cabinet

that will block the space under the

SOUNDSOLE 2.1. Blocking this space will

reduce overall bass performance.

3.5MM AUX STEREO AUDIO INPUT –ASingle 3.5mm Stereo; Connect to the Headphone Jack of any iPod, iPad,

Laptop or PC computer. This input is selected by pressing the Source button on the OSD AUDIO SOUNDSOLE 2.1

IR Remote. Use with devices not Bluetooth enabled, signal is Analog.

Multi Voltage

Switching Supply

Dual 5.25” Down-Firing Sub-Woofer

(1 Active, 1 Passive)

1 x 30 Watt Digital Low pass Power Amp

Page 6

IR REMOTE CONTROL

1. POWER - Press this button to turn the SOUNDSOLE 2.1 ON/OFF.

2. SRC; SOURCE- Press to select a connected source. The SOUNDSOLE 2.1 Front Panel Status LED will flash once to

indicate a change in input selection.

LINE IN1, AUX –3.5mm input, from Headphone Jack ANALOG connection

LINE IN2, RCA –Left and Right Signal Level Stereo RCA Input, ANALOG.

Optical LINE IN –Digital Fiber Optic Input

3. VOLUME -/+ Press VOL (-) to reduce volume. Press VOL (+) to increase volume.

4. DSP Effect –Advanced Digital Signal Processing which creates simulated surround sound from a stereo speaker

configuration. This will dramatically open up the sound stage making the appear to be coming from all over the room.

There are two choices for DSP settings. Typically you would use the Cinematic setting when watching a Video, Movie or

Television show. The Studio setting is recommended when listing to a 2 channel music source but does not guarantee

better sound but just different. It then comes down to a personal preference to the listener.

5. MUTE - Press this button once to mute the SOUNDSOLE 2.1. Press again to un-mute the SOUNDSOLE 2.1.

6. Press this button to initiate Bluetooth pairing mode. The Front Panel Status LED will rapid flash blue. The

SOUNDSOLE 2.1 will output a pairing code that will be picked up by any active Bluetooth device that is within range of

the SOUNDSOLE 2.1. Press to select a paired Bluetooth device. A Bluetooth device must be paired to the OSD AUDIO

SOUNDSOLE 2.1 for audio output. A paired Bluetooth device will remain ‘connected’ after changing inputs as long as

the Bluetooth device has not moved out of range, turned off or otherwise disconnected.

OSD Audio · 775 Columbia Street · Brea, CA 92821 · Tel: (562) 697-2600 · www.osdaudio.com Page 7

DESK/TABLE TOP INSTALLATION

The SOUNDSOLE 2.1 is ideally designed for desk and table top installation. In this application the SOUNDSOLE 2.1 is

placed on a Desk or cabinet top and becomes a pedestal for the TV/Monitor. Very little space is required beyond what is

already used by the TV/Monitor. The compact size 17.9”W x 12.4”D x 2.9”H makes it ideal for a Monitor stand in a

Home Office Setup and provides seamless integration while adding a true Sub-woofer Satellite system with Digital

Surround Processing.

DOWN-FIRING WOOFERS

The SOUND SOLE 2.1should always be placed on a solid

surface, maintaining the clearance on the bottom of the unit

required for low-frequency sound to freely radiate into the

room. Do not place objects next to the SOUNDSOLE 2.1

that will block this space. It recommended to keep two to

three inches all around the SOUNDSOLE 2.1 to get the

optimum sound from the Sub-woofer

Note: The TV pedestal should not be larger than the

top of the SOUNDSOLE 2.1 (17.9”W x 12.4”D x 2.94”H)

CABINET INSTALLATION

The cabinet /desk top should be at least Fifteen inches deep to

properly support the SOUNDSOLE 2.1. The SOUNDSOLE 2.1

is 12.4 inches Deep (with grille attached) and extra space will

be required between the SOUNDSOLE 2.1 and a wall behind

the cabinet for cables connecting the SOUNDSOLE 2.1to the

TV or other A/V sources (3 inches minimum).

Top View of Flat Panel TV/Monitors with

stand/base on top of the SOUNDSOLE 2.1

Page 8

AUDIO CONNECTIONS

The OSD AUDIO SOUNDSOLE 2.1 has three

Audio Input connections on the rear panel

that can be used for TV audio or connection

to other sources such as CD player, a

portable music player (that does not have

Bluetooth), a computer or any audio source

with one of the following output connections.

3.5mm AUX INPUT

Connect the 3.5mm AUX cable to the Headphone

output of any non Bluetooth device such as a iPod or

Laptop Computer. Headphone connection is Analog

and typically two channel stereo. Connect to the single

3.5mm to the single 3.5mm line 1input. This input is

selected by pressing the ‘SRC’ (source) button on the

SOUNDSOLE 2.1 IR Remote. It sequences through

line1, line 2 and optical input.

OPTICAL DIGITAL AUDIO

Connect the Optical Digital Audio OUT on a

TV or other source to the OSD AUDIO SOUNDSOLE

2.1 Optical Input using a Digital Optical Audio Cable as

shown. This Input is selected by pressing the SRC

button on the included IR Remote. NOTE: The audio

output of a TV, Blu-ray Disc player, game console, or

DVD player connected to the SOUNDSOLE 2.1 via

Optical Digital, must be set to PCM in the source’s

setup. Digital connection to a CD player does not

require a special setting.

L&R AUDIO

Connect the L&R Audio OUT on a TV or other source

to the SOUNDSOLE 2.1 L&R Audio Input using a

Stereo RCA-RCA Patch Cable as shown. This Input is

selected by pressing the ‘SRC’ (source) button on the

included IR Remote.

Sound Platform

Audio Inputs

EXTERNAL POWER SUPPLY

After all audio connections have been made and

confirmed, connect the female end of the included External

Switching Power Supply to the AC Input on the SOUNDSOLE 2.1

rear panel, and then plug the AC power cord into an un-switched

AC outlet. The AC connection is a universal power connection

that will automatically handle AC voltage from

100-240VAC.

RCA Stereo Patch Cords

Fiber Optic Digital Cable

Multi Voltage

Switching Power

Supply

3.5mm Stereo AUX Cable

Page 9

SIMULATED SURROUND

The SOUNDSOLE 2.1 utilizes advanced Digital Signal Processing (DSP) to create simulated

surround sound from a stereo speaker configuration. The SOUNDSOLE 2.1 simulated

surround can also be used for music (Effect button #2, Studio).

Press the #1 Effects button (labeled Cinematic) on the SOUNDSOLE 2.1 IR Remote to turn

the simulated surround ON if you want simulated surround while watching a Video. The Front

panel Status LED will flash once.

Press the same Effects button (#1) on the SOUNDSOLE 2,1 IR Remote to turn the simulated

surround OFF. Front panel Status LED will flash once. Do the same when listening to the

DSP effects #2 (Studio) when listening to music and you want to turn the effect off.

PAIRING AND SELECTING A BLUETOOTH SOURCE

The SOUNDSOLE 2.1 will pair without the need to enter a code, if the device implements Bluetooth v2.1 or later.

Legacy pairing is the only method available for Bluetooth v2.0 and older. Each device must enter a PIN code:

‘0000’ to complete pairing. To ensure that your device is compatible, look for the Bluetooth Music Icon on the

packaging, or go to: www.gadgetguide.bluetooth.com

PAIRING A BLUETOOTH DEVICE

1. Turn the SOUNDSOLE 2.1 and the Bluetooth device ON.

2. Press the button on the SOUNDSOLE 2.1 IR Remote to select the Bluetooth Input. The front panel Status LED

flash twice, delay then repeat.

3. On the device to be paired to the SOUNDSOLE 2.1, turn Bluetooth ON. The Bluetooth controls are typically

found in the device’s ‘Settings’ or ‘Connections’ menu. If the Bluetooth device has previously been paired with the

SOUNDSOLE 2.1, and the SOUNDSOLE 2.1 has not been removed from the list of discovered devices, the

Bluetooth device should automatically sync with the SOUNDSOLE 2.1. (Front panel Status LED solid blue.)

4. Press the button on the SOUNDSOLE 2.1 IR Remote for a Bluetooth device that has not been paired with the

SOUNDSOLE 2.1, or the SOUNDSOLE 2.1 has been removed from its list of discovered devices. The

SOUNDSOLE 2.1 will output a sync code that will be received by the Bluetooth device. The front panel Status

LED will flash rapidly until the Bluetooth device accepts the BT Code and pairs to the SOUNDSOLE 2.1.

5. The device will appear in the Bluetooth setup screen on the device being paired.

6. The device should sync to the SOUNDSOLE2.1. The front panel Status LED will stop flashing and illuminate solid

blue.

7. If switching between hardwired sources and a paired Bluetooth device, the Bluetooth device will remain

‘connected’ as long as the device has not been turned OFF or moved out of Bluetooth range. If the Bluetooth device

has been turned OFF, simply turn it ON, navigate to the device’s Bluetooth setup and sync to the SOUNDSOLE 2.1

OSD Audio

SOUNDSOLE 2.1

FRONT PANEL

Bluetooth Status LED

OSD Audio · 775 Columbia Street · Brea, CA 92821 · Tel: (562) 697-2600 · www.osdaudio.com Page 10

Indice

Altri manuali OSD Audio Sistema di altoparlanti

OSD Audio

OSD Audio NERO SB42 Manuale utente

Manuali Sistema di altoparlanti popolari di altre marche

JVC

JVC CA-MXK5R Manuale utente

LG NB4532B Manuale utente

JVC

JVC CA-FSH100 Manuale utente

5Core

5Core Pro Series Manuale utente

EAW

EAW MQV1394e Manuale utente

Lynx

Lynx GXR-LA10A Manuale utente

iLive

iLive ITB066B Manuale utente

RDX

RDX QuickStation 4 Manuale utente

Electro-Voice

Electro-Voice S-122 Manuale utente

Sven

Sven SPS-619 GOLD Manuale utente

Pioneer

Pioneer CS-7070 Manuale utente

EAW

EAW UB82e Manuale utente

Sondpex

Sondpex Active Speaker System and Digital Music... Manuale utente

JVC

JVC NX-PN7 Manuale utente

Marshall Amplification

Marshall Amplification AR-DM61-BT Manuale utente

Yamaha

Yamaha NX-A01 - Speaker Sys Manuale utente

SE Audiotechnik

SE Audiotechnik I-LINE Manuale utente

Gemini

Gemini WRX-843 Series Manuale utente