oticon BS-H200 Manuale utente
Phone Adapter 2.0
Instructions for use
Introduction to this booklet
This booklet gives you guidance on how to use and maintain your new phone
adapter. Please read the booklet carefully including the Warnings section.
This will help you get the most out of your phone adapter.
If you have additional questions about the use of your phone adapter, please
contact your hearing care professional.
For your convenience, this booklet contains the below navigation bar to help
you navigate easily through the different sections.
About Installation Handling Warnings More info
Intended use
Intended use Phone Adapter 2.0 is intended to be used together with Oticon
ConnectClip, Oticon Streamer Pro, and Oticon wireless hearing aids.
This enables the hearing aid user to communicate wirelessly with a
phone conversation partner via a landline phone (analogue/PSTN).
Indications for use No indications for use.
Intended user Adults and children older than 36 months.
User environment Indoor.
Contraindications No contraindications.
Clinical benefits See clinical benefits of the hearing aid.
Table of content
About
Package content 6
Phone adapter overview 7
Installation
Installation 9
Connect the phone adapter to a power outlet 10
Connect with phone line and landline phone 12
Pair Streamer Pro with the phone adapter 14
Pair ConnectClip with the phone adapter 16
Use the phone adapter 18
Handling
Incoming calls Streamer Pro 20
Outgoing call Streamer Pro 23
Incoming calls ConnectClip 26
Outgoing calls ConnectClip 29
Additional information 32
Warnings
General warnings 35
More info
Conditions of use 36
Technical information 38
International warranty 45
Australia only 46
Warranty 47
Phone Adapter
2.0
Instructions for use
About Installation Handling Warnings More info
6 7
Package content
The packaging box consists of the following elements:
Phone Adapter 2.0 Power supply
(The power supply may vary from country to country)
Phone cable
This booklet
About
Phone adapter overview
Front
Phone indicator
Condition Power indicator Phone indicator
Power on, no connection to the Streamer or ConnectClip
Pairing with the Streamer or ConnectClip
The Streamer or ConnectClip is wirelessly connected
Incoming call
Phone conversation
Fault condition (contact your hearing care professional)
No light Blinking Steady
Power indicator
OUT
IN
AUX
POWER
About Installation Handling Warnings More info
8 9
Back
Power supply
For PSTN wall adapter
For landline phone
ConnectLine in/out*
For more information please refer to: www.oticon.global/connectline
Installation
Installation
Use the phone adapter for the first time
Before you can use the phone adapter with your hearing aids, the phone adapter
must be connected to a power outlet and the public telephone line.
This is a step-by-step guide on how to install the phone adapter.
All needed parts for the installation are included in the package.
12
About Installation Handling Warnings More info
10 11
Connect the phone adapter to a power outlet
Use the power supply with USB cable from box 1
1. Plug the USB connector into the “power” connector on the phone adapter.
2. Plug the power supply into the mains wall socket or another power source.
3. Check that power is turned on.
4. After a few seconds the power indicator on the front of the phone adapter
will light up green.
Box 1
4.
2. and 3.
1.
IMPORTANT NOTICE
When charging the phone adapter, use the supplied original power supply
5.0V/1A, CE and safety marked.
12
About Installation Handling Warnings More info
12 13
Connect with phone line and landline phone
Place the phone adapter in a suitable spot near your landline phone or base
station.
1. Unplug the phone line from the landline phone (or base station).*
2. Plug the phone line from the wall adapter into the phone adapter
“IN” connector.
3. Plug the phone cable from box 2 in the phone adapter “OUT” connector.
4. Plug the other end of the phone cable into the landline phone (or base
station).*
Please lift off the handset from your landline phone – you should now be able
to hear the dial tone from the handset speaker.
Box 2
3.
2.
1.
4.
* If your main phone or base station does not have a detachable plug for the landline connection, you should either try using an
alternative phone or a technician must be contacted to complete the installation.
About Installation Handling Warnings More info
14 15
ON/OFF
Pair Streamer Pro with the phone adapter
The very first time your Streamer is used with the phone adapter, it must
be paired to the phone adapter.
For pairing:
1. Make sure the phone adapter is powered on, i.e. the power indicator is
steady green.
2. Press the ON/OFF button on the Streamer for 5-6 seconds until the blue
light starts blinking.
3. Place the Streamer on top of the phone adapter – the pairing takes around
20–60 seconds.
4. The pairing is completed when the power indicator on the phone adapter
and the indicator on the Streamer turns steady blue. Pairing is done only
once and will normally not have to be repeated.
Pairing Streamer Pro
Streamer Pro
top status
Streamer Pro
front
Phone
adapter
Description
-Streamer and
phone adapter on
-Streamer in
pairing mode
-Pairing complete
Steady Blinking
About Installation Handling Warnings More info
16 17
B
Pair ConnectClip with the phone adapter
The very first time your ConnectClip is used with the phone adapter, it must be
paired to the phone adapter.
For pairing:
1. Make sure the phone adapter is powered on, i.e. the power indicator is
steady green.
2. Press the multi button AND volume up button on the ConnectClip (B) for about
6 seconds until the status indicator blinks blue.
3. Place the ConnectClip on top of the phone adapter – the pairing takes around
20–60 seconds.
4. The pairing is completed when the power indicator on the phone adapter and
the status indicator on the ConnectClip turns steady blue. Pairing is done only
once and will normally not have to be repeated.
Status
Pairing ConnectClip
ConnectClip
Status
ConnectClip
Power
Phone
adapter
Description
ConnectClip and
phone adapter on
ConnectClip in
pairing mode
Pairing complete
Steady Blinking Power
Streamer Pro
See Page
22
ConnectClip
See Page
30
About Installation Handling Warnings More info
18 19
Use the phone adapter
The phone adapter supports both incoming and outgoing phone calls. During
a phone call the hearing aids are used as headsets and the microphone, on the
Streamer or on ConnectClip, enables hands-free operation.
Ensure the phone adapter is correctly installed as described in the following
section before you use the Streamer or ConnectClip for phone conversations
for the first time.
To use the phone adapter, the Streamer or ConnectClip and phone adapter
must be wirelessly connected to each other. This connection is established
automatically when the Streamer and phone adapter are paired and within
reach. The phone adapter is connected to the Streamer or ConnectClip when
the power indicator on the phone adapter is steady blue.
Indice
Altri manuali oticon Adattatore
oticon
oticon streamer Manuale utente
oticon
oticon FittingLINK 3.0 Manuale utente
oticon
oticon TVA3 Manuale utente
oticon
oticon ConnectLine Manuale utente
oticon
oticon ConnectLine Phone Adapter 2.0 Manuale utente
oticon
oticon ConnectLine BS-F200 Manuale utente
oticon
oticon ConnectLine Manuale utente
oticon
oticon ConnectLine Phone Adapter 2.0 Manuale utente
oticon
oticon ConnectLine TV 2.0 Manuale utente
oticon
oticon TVA3 Manuale utente
