oticon FittingLINK Manuale utente
INSTRUCTIONS FOR USE
Introduction to this booklet
This booklet gives you guidance on how to use and maintain FittingLINK. Please read the
booklet carefully including the Warnings section. This will help you get the most out of
FittingLINK.
If you have additional questions about the use of FittingLINK, please contact your local
distributor.
For your convenience, this booklet contains the below navigation bar to help you navigate
easily through the dierent sections.
About Start-up Handling Warnings More info
Intended use
Intended use FittingLINK is an accessory to the tting software used when
programming SBO wireless hearing aids. FittingLINK is intended for
wireless transfer of tting data between the hearing aids and the device
running the tting software. FittingLINK can be connected to the device
running the tting software through the provided Bluetooth adapter or
USB cable.
Indications for use No indications for use.
Intended user Hearing care professionals and hearing aid users.
User environment Hearing care professional's oce.
Contraindications Users of active implants must pay special attention when using the
device. For more information, read the warnings section.
Clinical benets See clinical benets of the hearing aid.
Table of contents
About
FittingLINK overview 6
Package content 8
Start-up
Basic functions - rst-time use 10
Turn FittingLINK ON/OFF 11
Charge FittingLINK 12
Charge FittingLINK with the charger and charging cradle 14
Charge FittingLINK with the charging cradle and USB cable 15
Charge FittingLINK without the charging cradle 17
Low battery indicator 18
Connect to a PC 20
Connect to a PC via the Bluetooth adapter 21
How to re-establish pairing between FittingLINK and the Bluetooth adapter 22
Connect to a PC via the USB cable 25
Handling
FittingLINK and tting software 26
How to use FittingLINK 27
How to use FittingLINK on children 34
How to use FittingLINK for coupler-based verication using
hearing aid analysers 36
Overview of LED indicators 38
Caring for FittingLINK 42
Warnings
Warnings 43
More info
Conditions of use 48
Technical information FittingLINK 49
Technical information Bluetooth adapter 51
Technical information 54
International warranty 55
6About Start-up Handling Warnings More info
FittingLINK overview
Neck loop
Front LED
indicator - blue
Front LED
indicator - red
Top LED indicator
Power supply
(and USB port)
ON/OFF button
ON/OFF
About
INSTRUCTIONS FOR USE
89
About Start-up Handling Warnings More info
Package content
The packaging box consists of the following elements:
USB cable 3 m
Box 1 Box 3Box 2
Bluetooth adapter
Charging cradle
Clip
Charger*
*Charger will vary from
country to country.
This booklet (Instructions for Use)FittingLINK
POWER
10 11
About Start-up Handling Warnings More info
Basic functions - rst-time use
Insert the USB cable in the bottom of the charging cradle and the charger is ready for use.
Turn FittingLINK ON/OFF
Power ON
Press the ON/OFF button on top of FittingLINK for about 2 seconds until you see a green steady
light from the top LED and a short red and blue ash from the front LED indicators. The LED lights
indicate that FittingLINK is powered on and you can release the ON/OFF button.
If FittingLINK cannot power on, make sure it is charged.
If the top LED shows a red light instead of the green light the battery is running low (steady red
light) or very low (ashing red light) and FittingLINK should be charged. Please refer to “Charge
FittingLINK”.
Power OFF
Press and hold the ON/OFF button on top of FittingLINK for about 2 seconds until the top LED
indicator turns o.
Start-up
12 13
About Start-up Handling Warnings More info
Charge FittingLINK
FittingLINK uses an internal rechargeable battery.
FittingLINK can be charged either by using the provided charger and charging cradle or by using
the USB cable provided.
When charging FittingLINK for the rst time, it should be left to charge for at least two hours even
if the top LED indicator on the device shows that the battery is fully charged. We recommend that
you turn o and store FittingLINK in the charging cradle whenever it is not in use, to ensure the
best possible performance.
It is safe to leave FittingLINK in the charging cradle overnight – the battery cannot be
overcharged.
Charging
Top LED
indicator
Description
Device on and fully charged
Device on and charging
Device o and charging
Once fully charged, the LED will be o
Steady Flash
IMPORTANT NOTICE
When charging FittingLINK, use the supplied original power supply 5.0V/1A,
CE and safety marked.
IMPORTANT NOTICE
When charging, the charging indicators should be lit as described in this booklet.
If the charging indicators are not lit as described, disconnect the device from the charger and
consult your local distributor.
14 15
About Start-up Handling Warnings More info
Charge FittingLINK with the charger and charging cradle
Place FittingLINK in the charging cradle when you want to charge FittingLINK with the provided
charger and charging cradle. Remember to connect the charger to a power outlet. As soon as the
power is switched on, FittingLINK will start charging.
Charge FittingLINK with the charging cradle and USB cable
When charging FittingLINK with the provided charging cradle and the USB cable, place
FittingLINK in the charging cradle and connect the USB cable to a USB port on your PC.
Please note that if you charge via a USB hub, some hubs do not deliver enough power to actually
charge FittingLINK. In this case we recommend use of the provided charger instead.
16 17
About Start-up Handling Warnings More info
Only recharge FittingLINK using the provided charger or a stabilised USB hub/charger that
provides 5VDC and ≥500 mA.
Charge FittingLINK without the charging cradle
If you prefer not to use the charging cradle when charging FittingLINK, you have the option to
insert the USB cable directly into FittingtLINK instead of the charging cradle.
Note: When using the USB cable, always insert the USB cable into FittingLINK before connecting the cable to other
equipment.
18 19
About Start-up Handling Warnings More info
Low battery indicator
FittingLINK will indicate low battery (about 20 minutes programming capacity left) with a steady
red light, and very low battery (about 5 minutes programming capacity left) with a ashing red
light.
Low battery indicator
Top LED
indicator
Description
Low battery – about 20 minutes capacity left
Very low battery – about 5 minutes capacity left
Steady Flash
To ensure the best possible performance, we recommend that you turn o and store FittingLINK
in the charging cradle whenever it is not in use.
The battery should not be drained completely. Keeping the battery fully charged will prolong the
capacity of the battery. The battery cannot be replaced by the user.
The battery capacity is up to 8 hours of typical daily use.
Battery charge time is 2 hours for complete charge, using the provided power supply.
Indice
Altri manuali oticon Apparecchiature di registrazione
Manuali Apparecchiature di registrazione popolari di altre marche
Strymon
Strymon NIGHTSKY Manuale utente
Mitsubishi Electric
Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manuale utente
Tews Technologies
Tews Technologies TPMC465 Manuale utente
Honeywell
Honeywell Excel 50 Manuale utente
SeaLevel
SeaLevel COMM+8.LPCI Manuale utente
Arturia
Arturia AUDIOFUSE STUDIO Manuale utente
