Outback Power Systems FLEXware 1000 Manuale utente

European Sales Ofﬁce

Barcelona, España

(+34) 600-843-845

19009 62nd Avenue NE

Arlington,WA USA

(+1) 360-435-6030

www.outbackpower.com

900-0062-1

1000

User’s Guide

Includes Mounting, Installation, and

Product Registration

1000 Manual.indd, Spread 1 of 12 - Pages (24, 1) 11/22/06 11:07 AM

OutBack Power Systems FLEXware is a system of modular aluminum mounting hardware and installation

components designed for convenient system installation and integration.

About OutBack Power Systems

OutBack Power Systems is a leader in advanced energy conversion technology. Our products include

true sine wave inverter/chargers, a maximum power point charge controller, system communication

components, as well as breaker panels, breakers, accessories, and assembled systems.

Notice of Copyright

Disclaimer

UNLESS SPECIFICALLY AGREED TO IN WRITING, OUTBACK POWER SYSTEMS:

(a) MAKES NO WARRANTY AS TO THE ACCURACY, SUFFICIENCY OR SUITABILITY OF ANY TECHNICAL OR

OTHER INFORMATION PROVIDED IN ITS MANUALS OR OTHER DOCUMENTATION.

(b) ASSUMES NO RESPONSIBILITY OR LIABILITY FOR LOSS OR DAMAGE, WHETHER DIRECT, INDIRECT,

CONSEQUENTIAL OR INCIDENTAL, WHICH MIGHT ARISE OUT OF THE USE OF SUCH INFORMATION. THE

USE OF ANY SUCH INFORMATION WILL BE ENTIRELY AT THE USER’S RISK.

Date and Revision

September 25, 2006 1.0

Contact Information

OutBack Power Systems

19009 62nd Ave. NE

Arlington, WA 98223

Phone (360) 435-6030

Fax (360) 435-6019

www.outbackpower.com

Product Registration

Please take a moment to register and provide us with some important information. Send to:

OutBack Power Systems, 19009 62nd Avenue NE, Arlington, WA 98223 USA.

Name: ��

Address: ��

City, State, Zip Code: ��

Country: ��

Telephone Number: ��

E-mail: ��

Sold by: ��

Installer: ��

Purchase Date: �� Model Number: ��

Serial Number: ��

Check all that apply:

mO-Grid Installation mGrid-Tie Installation mResidential Installation mCommercial Installation

1000 Manual.indd, Spread 2 of 12 - Pages (2, 23) 11/22/06 11:07 AM

Requirements and Warnings

The OutBack FLEXware 1000 enclosures (FW1000-AC and FW1000-DC) are listed by ETL as an

indoor enclosure to UL standard UL 508A Industrial Control Panels.

This enclosure is intended for battery circuits congured for 12 to 48 volts nominal.

Grounding Instructions – Each enclosure should be connected to a grounded, permanent wiring

system. For most installations, the negative battery conductor should be bonded to the ground-

ing system at one (and only one) point in the DC system. All installations should comply with all

national and local codes and ordinances. System grounding as required by the National Electric

Code, ANSI /NFPA 70-1996, is the responsibility of the system installer.

The equipment ground on FLEXware1000 is marked with this symbol:

FLEXware is designed for indoor mounting only with appropriate fasteners and a secure mounting

surface that can handle the full weight of an assembled system.

1000 Manual.indd, Spread 3 of 12 - Pages (22, 3) 11/22/06 11:07 AM

Welcome to OutBack Power Systems’FLEXware

FLEXware is a convenient all-aluminum power system oering simpler, code-compliant installation

of OutBack power electronics components. Three versions of FLEXware are available:

• FLEXware 250 for single FX Series Inverter/Charger installations along with the desired AC and

DC disconnects

• FLEXware 500, which supports up to two FXs and two MX Charge Controllers, accommodating

both split-phase and/or higher power output as needed

• FLEXware 1000 accommodates up to four FXs and four MX Charge Controllers

Please Note: Both the FLEXware 500 and the FLEXware 1000 power systems provide locations for

FW-X240 Auto-Transformers, multiple DC shunts and other essential components required in

higher kW systems.

1000 Manual.indd, Spread 4 of 12 - Pages (4, 21) 11/22/06 11:07 AM

Figure 15: Wiring Diagram

FW1000-AC

IOB Kit

HUB

AC Breakers

FW-X240 Breaker

MX60s

DC Breakers

Wiring Raceway

PV+ and Bat+

breakers

FW1000-DC

Figure 1: FLEXware 1000 System

Getting to Know FLEXware 1000

FW-MP

ACA FX (with DCC) DCA

1000 Manual.indd, Spread 5 of 12 - Pages (20, 5) 11/22/06 11:07 AM

Figure 2: Front View Side View

Knockouts and Dimensions

Figure 14: OutBack HUB

Installing an OutBack HUB

An OutBack HUB allows the FX Series Inverter/Chargers, MX60 Charge Controllers, and MATE

to communicate with each other. It attaches (see arrows in Figure 14) to the outside of the

FW1000-AC (hardware included with the HUB).

HUB connection

1000 Manual.indd, Spread 6 of 12 - Pages (6, 19) 11/22/06 11:07 AM

Figure 14: FLEXware Wiring Raceway

When all component and cabling installations are complete, install the FLEXware Wiring Raceway

to cover and protect the exposed communication cables running between the AC and DC sides

of the system. The illustration above shows FLEXware Mounting Plates with components removed

for clarity.

A complete FLEXware 1000 System consists of the following in addition to the FW1000-AC

and FW1000-DC:

• two FLEXware Mounting Plates (FW-MP)

• FLEXware Wiring Raceway (included with AC chassis)

• four FX Series Inverter/Chargers

• AC Conduit Adapter (ACA) and a DC Conduit Adapter (DCA), which connect each FX to the

FW1000-AC and FW1000-DC

• MX60 Charge Controller(s) (normally part of this system) and mounting brackets

• AC and DC breakers including a specic AC Input/Output/Bypass Breaker (IOB) Kit

• bus bars and DC current shunts as required per specic installation

• DC and AC ground fault protection

Some systems will work optimally with a FW-X240 Auto-Transformer installed.

Note: Be sure you have all the parts required for your intended system installation. As every

installation is dierent, consult with your dealer or installer for further information.

FLEXware 1000 Parts List

FLEXware 1000 consists of the FW1000-AC and FW1000-DC. Each is an aluminum chassis for

mounting AC and DC breakers, respectively, along with the components listed below:

FW1000-AC components:

• aluminum enclosure

• DIN rail bracket

• TBB-GROUND

• Breaker and Bypass Mounting Bracket

• FW Wiring Raceway with mounting hardware

• metal hanging straps for combining

two FW-MPs

FW1000-DC components:

• aluminum enclosure

• 500 amp shunt with TBB

• TBB-GROUND

• one FW breaker bus

• two shunt bus bars

• two DC Breaker Mounting Brackets

• FXW1000-DC Hardware Kit

1000 Manual.indd, Spread 7 of 12 - Pages (18, 7) 11/22/06 11:07 AM

Installation Tips

• Never use less than the minimum recommended number and type of fasteners when installing

the FLEXware Mounting Plates.

• Each FX weighs in excess of 50 lbs and is often more easily installed by two people rather

than one.

• Be sure the DC enclosure is secured to the FLEXware Mounting Plate before attaching the

MX Charge Controller to it.

• Installation of each enclosure and breakers is normally easier by removing the breaker brackets

rst. Do not remove any breaker knockouts from these brackets without referring to the chosen

AC IOB kits and DC breaker selections rst.

• It is also easier if all conduit knockouts are removed before mounting the enclosures.

Mounting and Installation

FLEXware 1000 is designed for mounting on the FLEXware Mounting Plate (FW-MP). Although the

components can be secured to other surfaces, the FW-MP is an engineered platform designed

for the FLEXware 1000 installation. This manual illustrates such an installation. OutBack does not

endorse other installation methods and therefore cannot recommend fasteners or other means of

attachment due to the variety of installations possible in the ﬁeld.

Please see the FLEXware Mounting Plate Instructions for further information.

In addition to installing the AC and DC chassis, a typical installation includes four FX Series Invert-

er/Chargers, one or more MX Charge Controllers, a HUB Communications Manager, and AC and

DC Conduit Adapters. The installation of these components is also displayed in these instructions.

TSlot indicates this is the top edge of the FW-MP

Figure 3: FLEXware Mounting Plate

The MX Charge Controller attaches

to the chassis using three #10 X 3/8”

sheet metal screws included in the

hardware kit. Two are inserted from

inside the MX and the third through

the hanger on the top of the MX.

MX Knockouts

Figure 13:

MX Charge Controller 1” knockouts

Charge

Controller

knockouts

1000 Manual.indd, Spread 8 of 12 - Pages (8, 17) 11/22/06 11:07 AM

MX60 Installation

A FLEXware 1000 System installation includes up to four MX Charge Controllers which can be

mounted on both the top and side of the FW1000-DC. Newer MXs have rear knockouts allowing

them to be mounted directly to the side of the enclosure without the need for additional

mounting brackets. Mounting brackets are required for top installation of all MX models and for

side installation of less recent models..

Figure 12:

MX Charge Controller mounting options

Bracket screw locations are

shown below

Screw locations for directly attaching an

MX Charge Controller are shown below

Figure 4: Two mounting plates installed

Note: Check that both FW-MPs are level as per the FLEXware Mounting Plate Installation Manual. If

space is restricted, the FW-MPs can be installed vertically.

With the Mounting Plate and the hanging screws (for the FX Series Inverter/Chargers) installed,

install the FXs.

• Start with the top FX.

• Hang the FX on the hanging screws, but continue to hold onto it.

• Loosely install four M6 X 20 mm screws, included with the FW-MP, one in each corner; tighten

them when all four are installed and the FX is aligned.

• Install the remaining FXs in the same manner.

Hanging Straps

1000 Manual.indd, Spread 9 of 12 - Pages (16, 9) 11/22/06 11:07 AM

Figure 5: Four FXs installed on FW-MPs

Note: The hanging straps are now removed.

Plastic bushing,

DC side

Figure 11: DCA bushing

Note: The DCA will be held rmly in place when the DCC (FX cover) is secured at the end of

the installation.

To install an ACA:

• Follow the separate ACA instructions for mounting to the FX.

• Line the ACA up with the conduit hole in the AC Chassis.

• When aligned, move the AC chassis snug against the ACAs after the ACA installations.

• Press a 1” plastic bushing from inside the AC chassis out to the ACA through each previously

removed knockout, sliding the AC chassis against the ACAs until snug.

• With all the ACA’s aligned with the AC chassis and the bushings installed, tighten the AC chassis

screws against the FW-MP.

With both the AC chassis and DC chassis installed, the breaker brackets, AC din rail(s), and

optional AC and DC breakers can be installed. Please see the individual Input/Output/Bypass

Breaker (IOB) kit for instructions.

1000 Manual.indd, Spread 10 of 12 - Pages (10, 15) 11/22/06 11:07 AM

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Outback Power Systems Allegato

Outback Power Systems

Outback Power Systems OBE-3-FT Manuale utente

Manuali Allegato popolari di altre marche

SilentiumPC

SilentiumPC Armis AR5 Manuale

Pulsar

Pulsar 17/TRP80/DSPR Manuale utente

Thermaltake

Thermaltake V150 TG Manuale utente

MSI

MSI MPG SEKIRA 500X Manuale utente

Antec

Antec Dark fleet DF-10 Manuale utente

Nexans

Nexans WTC05 Manuale utente

Peavey

Peavey DS 1502 Manuale utente

D-Link

D-Link ShareCenter Pro DNS-1550-04 Manuale utente

Rosewill

Rosewill RX82-U(JBOD) Manuale utente

QNAP

QNAP SAS JBOD CLI 1.0 Manuale utente

GAMDIAS

GAMDIAS Talos P1 Manuale utente

Auvs

Auvs KR615 Manuale utente

Digitus

Digitus DA-71114 Manuale utente

CommScope

CommScope FDH 3000 Manuale utente

FS FHD-FWME4 Manuale utente

JBL

JBL CS1215T Manuale utente

Pulsar

Pulsar ARAD-S4 Manuale utente

Pulsar

Pulsar AWO454 Manuale utente