Ovislink EVO-DSL SERIES Manuale utente

EVO-DSL Series

Wired & Wireless

ADSL 2+

ROUTER

Quick installation guide

Guide d’installation rapide

Guía rápida de instalación

Guia de instalação

ADSL2+ ROUTER

Thank you for trusting OvisLink. Your satisfaction is our goal and we assure you our quality

products will meet your expectations.

PACKAGE CONTENT:

Before installing this modem router, check that elements listed here are present:

- A router

- A power supply

- RJ-11 cable

- ADSL filter

- Ethernet Cat. 5 RJ-45 crossed cable

- USB cable (only Evo-DSL11)

- This user’s guide

If any element is missing, please contact with your distributor.

LEDs PANEL:

Evo-DSL11 Steady light Flashing Fast flashing Off

POWER (red) Power on / / Power off

LINK (yellow) The modem is in

good connection

In handshaking

status /Connection not

set up

DATA (green) Wan is con-

nected /Transmitting or

receiving data

Wan is not con-

nected

Green Ethernet line is

connected /Transmitting or

receiving data

Ethernet line

not connected

properly

Red USB is connected / Transmitting or

receiving data

USB is not con-

nected properly

Orange USB and Ethernet

are connected /Transmitting or

receiving data

USB and

Ethernet are

not connected

properly

Evo-DSL41 &

Evo-DSL41W Steady light Flashing Fast flashing Off

POWER (red) Power on / / Power off

ENGLISH

DSL (yellow)

The modem is

in good con-

nection

In handshaking

status /Connection not

set up

Internet (green) Wan is con-

nected /Transmitting or

receiving data

Wan is not con-

nected

LAN / Wireless

(green)

Ethernet line

or Wireless is

connected

/Transmitting or

receiving data

Ethernet line

or Wireless

not connected

properly

CONNECTORS:

The connectors are on the back panel :

Evo-DSL11

Evo-DSL41

Evo-DSL41W

LINE Connected with phone line or “ADSL” port of the splitter.

ETHERNET or LAN To be connected to a PC network card by a straight-through network

cable, also can use a crossover cable to connect to Switch or Router.

USB To be connected to a PC by an USB cable

SWITCH To turn on / off the power.

POWER Power interface, Connect with power adapter.

RST

Press the reset button and turn on the power, then keep pressing the

reset button for 5 seconds. Then you can reset the modem with the

default settings.

ENGLISH

Note : With Evo-DSL41 and Evo-DSL41W, the Reset button is placed under the product, near to a rubber

foot.

HARDWARE INSTALLATION:

1) Use a telephone cord to connect the LINE port of the splitter with the RJ-11 port

(the phone jack) on the wall.

2) Use another telephone cord to connect the ADSL port of the splitter with the LINE

port of the ADSL Modem.

3) Use another telephone cord to connect the telephone set with the PHONE port of the

splitter.

4) Connect Ethernet port of the router with 10/100BASE-T port of the computer using the

network cable that comes with the modem. If you have a Evo-DSL11 and you want to

use the USB port, please, insert the CD-Rom first, and install the driver (setup.exe).

After that, you can plug the USB cable.

5) Plug in the power cord, and turn on the power.

COMPUTER SETUP:

1) Configure the IP adress of the computer on automatic (DHCP client), which will allow

the modem/router to set a proper IP adress to the computer so that the whole

configuration and the internet connexion can be done.

2) If you use Windows 2000/XP, open the Configuration Panel and then the Network

Connections.

3) Right click on the Local Network Connection and choose Properties.

4) Click twice on Internet Protocol TCP/IP.

5) Select the automatic IP adress.

6) Select automatic DNS server adresses.

7) Click on OK.

8) Click on Close.

Once the windows are closed, check the configuration of your internet browser.

ENGLISH

BROWSER SETUP:

1) The browser must be setup so that it connects directly to the internet, without requiring

any proxy or automatic configuration.

2) For Internet Explorer, open your browser, and click on Tools and Internet Options...

3) Click on Connexion tab and select Never connect.

4) Then, click on the button Network Parameters and uncheck everything. Click on OK.

5) Click on OK to close the Internet Options.

Once the options are validated, keep the Internet browser open to configure the router.

INTERNET CONNECTION:

1) In the internet browser (IE, Firefox, ...), enter the following address :

http://192.168.1.1

2) You are then asked to enter an username and a password to be granted access to

the configuration pages of the router. Enter these names :

Username: admin

Password: password

3) Now, you’re in the web interface of the router. Please, click on WAN link.

4) You find a table with all the default configuration. All is in Bridge mode, so you’re

router are working as a simple adsl modem. To enable the router feature, please,

click on the Edit button in front of your VPI/VCI configuration or on the Add button.

ENGLISH

5) You can see the VPI/VCI values. Don’t modify them and click on Next button.

6) Now, you can choose your connection type. In most of case, you must use PPPoE

connection, so we’ll detail this option. Select the PPP over Ethernet option and select

your Encapsulation mode. Click on Next button.

7) Please, enter your username and password of your internet connection (please, see

your FAI contract) and click on Next button.

8) Check that the « Enable WAN Service » option is selected, and you can change the

ENGLISH

Service Name if you want (no need for the internet connection). Click on Next button.

9) Now, you can see a summary table of your internet connection. Click on Save button.

WIRELESS SETUP (only for Evo-DSL41W):

1) Click on Wireless link.

2) Click on Basic link. In this part, you can enable/disable the wireless feature and

configure it. Change the SSID (name of the wireless network) if you want and select

your country. Click on Save/Apply button.

3) Click on Advanced link to change only the chanel, if you need it (to avoid some

connection issues with other access point). Click on Save/Apply button.

ENGLISH

4) Now, we’ll go to secure the wireless network. Click on security link, select your SSID,

and we advice you to select WPA-PSK in the Network Authentication list. After that,

enter a WPA Pre-Shared Key that will be the encryption key for your wireless network.

Click on Save/Apply button.

ADVANCED SETUP:

This part is reserved to professional networkers. You can reach the advanced setup by

using the following address :

http://192.168.1.1/main.html

By this way, you can configure a port-forwarding, setup the firewall, ...

TECHNICAL SPECIFICATIONS:

Evo-DSL11

 •Interfaces:

- 1 x RJ45 10/100 Mbps port

- 1 x RJ11 Adsl port

- 1 x USB port

 •Adsl2+modemuntil24Mbps

 •WANmode: Bridging, PPPoA, PPPoE, MER and IPoA

 •Features: NAT, NAPT, Firewall, DHCP Server, SNMP and Parental Control

Evo-DSL41

 •Interfaces:

- 4 x RJ45 10/100 Mbps ports

- 1 x RJ11 Adsl port

 •Adsl2+modemuntil24Mbps

 •WANmode: Bridging, PPPoA, PPPoE, MER and IPoA

ENGLISH

 •Features: NAT, NAPT, Firewall, DHCP Server, SNMP, Parental Control, Virtual

Servers, Dynamic DNS, DMZ and UPnP

Evo-DSL41W

 •Interfaces:

- 4 x RJ45 10/100 Mbps ports

- 1 x RJ11 Adsl port

- Wireless 802.11g 54 Mbps

 •Adsl2+modemuntil24Mbps

 •WirelessSecurity: WEP, WPA, 802.1x RADIUS and ACL

 •WirelessFeatures: WDS (Bridge/Repeater) and Universal Repeater

 •WANmode: Bridging, PPPoA, PPPoE, MER and IPoA

 •Features: NAT, NAPT, Firewall, DHCP Server, SNMP, Parental Control, Virtual

Servers, Dynamic DNS, DMZ and UPnP

 •VPNIPSec

Information of radio usage in the European Community:

Channel

Number

Center

Frequency

North

American

FCC

ETSI

Singapore Japan Israel

France All

Others

1 2412 MHz X X** X - X -

2 2417 MHz X X** X - X -

3 2422 MHz X X** X - X X

4 2427 MHz X X** X - X X

5 2432 MHz X X** X - X X

6 2437 MHz X X** X - X X

7 2442 MHz X X** X - X X

8 2447 MHz X X** X - X X

9 2452 MHz X X** X - X X

10 2457 MHz X X X X X -

11 2462 MHz X X X X X -

12 2467 MHz - X X X X -

13 2472 MHz - X X X X -

**Note: Channel can be used at a maximum of 10 dBm EIRP

ENGLISH

Indice

Lingue:

Altri manuali Ovislink Router di rete

Ovislink

Ovislink EVO-WR54ADSL-2 Manuale utente

Ovislink

Ovislink AirLive GW-300NAS Manuale utente

Ovislink

Ovislink OV303R6 Manuale utente

Ovislink

Ovislink AirMax5N Manuale utente

Ovislink

Ovislink OV604VB Manuale utente

Ovislink

Ovislink Air Live GW-300R Manuale utente

Ovislink

Ovislink Air Live WN-220R Manuale utente

Ovislink

Ovislink Live-FSH16T+ Manuale utente

Ovislink

Ovislink OV504WN Manuale utente

Ovislink

Ovislink AirLive Ether-FSH2400NS Manuale utente

Ovislink

Ovislink WHR-609N Manuale utente

Ovislink

Ovislink OV704WVG Manuale utente

Ovislink

Ovislink OV504WN Manuale utente

Ovislink

Ovislink OV804WVA Manuale utente

Ovislink

Ovislink Ether-GSH4T Manuale utente

Ovislink

Ovislink Air Live IE-840POE Manuale utente

Ovislink

Ovislink AirLive Live-5G Manuale utente

Ovislink

Ovislink AirLive WIAS-1000G Manuale utente

Ovislink

Ovislink Air Live WT2000ARM Manuale utente

Ovislink

Ovislink AirLive Live-FSH16T+v2 Manuale utente

Ovislink

Ovislink OV604V Manuale utente

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza