Owlet Cam 2 Manuale utente
1
Owlet Cam 2 Installation Guide
2
Let’s Get Started
Download the Owlet App.
Plug in and follow app instructions
to pair the Cam 2 with your Owlet
Account.
If you’ve already downloaded the
Owlet App, click the Account tab to
add a new device.
EN
Guide to Owlet Cam 2 Status Lights
(blinking red/blue) Cam 2 is ready to pair with App
(red) User is actively streaming via App, using background audio, or the Cam is rebooting.
(blinking blue) Cam 2 is trying to connect to Wi-Fi
(blue) Cam 2 is connected to internet. App is not streaming
Remember: the Cam 2 allows for video
and audio via secure, encrypted
Wi-Fi. Only connect the Cam 2 to a
private network that requires
a secure password.
3
Choose Your View
Place the Cam 2 and all cables 36 inches
(92 cm) away from the edge of the crib.
Cables within 36 inches (92 cm) of the
edge of the crib should be covered.
You can set up the Cam 2 in two ways:
1 Place it on a flat surface using the
magnetic base and adjust for
desired tilt angle.
2Mount it on a wall above the crib
using the base as a wall mount for
a bird’s-eye view of the crib or for
an expanded view of your nursery.
The next steps will guide you through
mounting the Cam 2 on the wall
(above the crib).
You can also view our Installation Video
at support.owletcare.com
4
What’s in the Box
Owlet Cam 2
Mounting
plate
Magnetic base
Measuring tape
(not included)
Cables with Owlet wraps*
and room temperature and humidity sensor
21x cable guards
18x long guards
1x end piece
2x L-brackets
Power adapter
Small Phillips screwdriver
(not included)
1x screw
Wall Mounting Kit Tools Needed to Mount the Cam 2
5
1. Measure and mark
Consider which outlet to use. The
outlet should be at least 36 inches
(92 cm) away from the crib to ensure
no exposed cables will be within
baby’s reach. The next steps will
instruct you on how to cover
all cables.
Measure 36 inches (92 cm) (92 cm)
from the top of your baby’s mattress
and make a mark on the wall — this
is where the Cam 2 will be mounted.
Center this mark above baby’s crib for
the optimal viewing angle.
36 inches
(92 cm)
36 inches (92 cm)
(six cable guards)
It’s also important to consider the
location of the temperature and
humidity sensor. The temperature
sensor can be found near the end
of the smart cable on the side that
connects to the power adapter.
6
3. Unwind the cable 4. Thread the cable
Remove the cable wraps and
unwind the cable.
Thread the cable down the channel
of the mounting plate, aligning the
orange sticker on the cable to the top
of the mounting plate.
2. Align and fasten
Align the center hole of the mounting
plate with the mark you’ve made on
the wall. Using the provided screw,
fasten the mounting plate to the wall
with the arrows pointing upward.
sticker
7
5. Mount the base
Position the large holes of the
magnetic base over the protruding
tabs on the mounting plate, then slide
downward until it clicks.
sticker
Attach the Cam 2 to the magnetic
base. Plug the cable into the Cam 2.
6. Attach the Cam 2
The orange sticker should be
placed just above the mounting
plate so that you have enough
cable slack to position the Cam 2
to your desired angle.
8
The cable guards use high-strength
adhesive. Take your time during
installation to ensure proper placement.
1Peel off adhesive cover from the
back of a long guard
2Thread cable down the center
of a long guard
3Snap long guard onto the
bottom of the mounting plate
4Press firmly onto wall
5Repeat steps 1–4 with remaining
long guards until you reach the
height of the wall outlet
7. Mount cable guards
long guard
9
Use the right or left L-bracket to guide
the cable in the direction of the wall
outlet.
Install long guards until any cable
within 36 inches (92 cm) of the edge
of the crib is covered. Continue adding
long guards as needed to reach the
outlet. Finally, install the end piece
when you are within 6-10 inches of
the outlet (this allows enough room to
wrap excess cable with velcro).
8. Mount L-bracket
L-brackets
end piece
10
For contact information specific to
your region, please visit
https://support.owletcare.com
Need Help?
Gather the excess cable into a loop.
Secure the top section of the loop
by feeding the cable wrap through
the first hole. The Owlet logo faces
outward. Secure the bottom section
of the loop to the top section by
feeding the cable wrap through the
second hole (The loop should now
look like a bow). Secure remaining
cable wrap.
Once the excess cable has been
wrapped securely, connect the power
cable to the power adapter and plug
it in.
You’re all set! You can now use the
App to reference how to adjust the
Cam 2 angle until you achieve the
desired view.
9. Wrap excess cable with velcro
Altri manuali per Cam 2
1
Indice
