PAC SWI-PS Manuale utente

06-14-07

SWI-PS

Universal Steering Wheel Control Interface

Before You Start

A. Is this product compatible with the vehicle?

• See application guide (seperate sheet) for listing of vehicles and connection information. If not, check www.pac-

audio.com for an updated list of compatible vehicles.

B. Prepare for the installation.

• If possible, install the SWI-PS while you are installing the new head unit. Keep in mind you may need to plug in the

factory stereo to locate certain wires; therefore do not complete the head unit installation until the SWI-PS is work-

ing properly.

• Plan a general installation location for both the SWI-PS plug and the control body. Keep in mind that the supplied

wire harness is two feet long, and the 1/8" plug harness is three feet long.

• Use a multimeter or approved measuring device for checking vehicle circuits.

Pacific Accessory Corporation

SEEK

PRESET

AM FM

VOLUME

PLAY MUTE

Power

IP-BUS input

Antenna jack

Fuse Jack for the SWI-PS

IP-BUS cable

Steering wheel

audio control wire

Installation Instructions

For Pioneer and Sony Radios

with wired remote inputs.

Wiring Connections

Step 1.

Connect the BLACK

wire to ground (-).

Verication: Wire

or location registers

a constant (-) when

probed.

Step 2.

Connect the RED wire

to switched +12V.

Verication: Wire reg-

isters +12V when the

ignition key is turned

to the ACC or ON posi-

tions.

Step 3.

Connect the appropriate interface wire (WHITE, YELLOW, ORANGE or

GREEN).

• Refer to the Identication and Connection Chart. Locate the vehicle and

note the SWC wire color in the “Interface Wire Color” column.

• Note the vehicle wire color and location information in the “Identication”

column.

Note: You will only connect ONE of these wires. The other 3 wires will not

be used. Cut and insulate the unused wires.

• Connect the wire as indicated in the chart.

Note: Only 3 wires will be used during installation. Only GM vehicles programmed for version #4, will use 4 wires.

Step 4a.

Connect the BLUE

serial data wire.

Connect this wire

ONLY on GM

passenger vehicles (no

trucks or SUVs) with

airbags AND steering

wheel heater controls.

For all other vehicles,

cut and insulate the

BLUE wire.

Step 4b.

If instructed by the

Vehicle Application

Guide, cut the

BROWN wire loop and

insulate both halves.

Step 4c.

If instructed by the

Vehicle Application

Guide, cut the VIOLET

wire loop and insulate

both halves, or place a

resistor in-line of wires.

Note: Step 4a is for vehicles made by

General Motors that are programmed

for version #4 only. If no connections is

necessary, proceed to Step 4b.

Step 4

If necessary, perform the following operations as indicated by the notes in Identication and Connection Chart.

06-14-07

SWI-PS

Programming the SWI-PS to Work With the Vehicle

Step 6.

Press and hold programming/

mode button on SWI-PS. Turn the

vehicle ignition to the ON position.

The LED on the

SWI-PS will light.

Step 7.

Release the programming/

mode button.

The LED will turn off,

indicating memory is

cleared.

Step 8.

Press and release the program-

ming/mode button the same

number of times as the desired

version number.

The LED will ash

each time the button is

pressed and released.

Step 9.

After 3 seconds, the

LED will ash the same

amount of times of set

version number.

Step 10.

Turn vehicle ignition

to OFF position.

Vehicle programming

sequence is complete.

SWI-PS

OFF

ACC

IGN

STRT

OFF

ACC

IGN

STRT

SWI-PS

Step 5.

Refer to The Vehicle Appication Guide. Note the INTERFACE Version Number next to the selected vehicle. Fill in the information

below for quick reference.

Version Number: ____________

(Write Version Number here)

SWI-PS

Step 18.

Press and

hold program-

ming/mode

button on

SWI-PS.

LED will light.

Step 19.

Release

programming/

mode button.

SWI-PS

You only need to press the programming/mode button once to program all the buttons. If you press this button again after the

interface is programmed, it will erase all previous learned buttons.

SWI-PS

If you programmed the interface for version #4, proceed with the following steps.

If you did not program the interface for version #4, skip to Step 18.

Step 12.

Press and hold

programming/

mode button

on SWI-PS.

Step 14.

Press and hold the TEMP UP

button on the steering wheel

control.

LED will turn off.

LED will light.

Step 13.

Release

programming/

mode button.

Step 15.

Release the TEMP UP button.

LED will turn on. The

function is pro-

grammed.

Step 16.

Repeat Steps 14 and 15, using the TEMP DOWN Button.

Step 17a.

If the vehicle is equipped with FAN UP and FAN DOWN buttons:

Repeat Steps 14 and 15 for these buttons as well.

Step 17b.

If the vehicle is NOT equipped with FAN UP and FAN DOWN buttons:

Press and release the programming/

mode button on the SWI-PS.

SWI-PS

In either case, the

LED will ash once

and stay on.

Skip to Step 20.

You have 7 sec-

onds to perform

the next step.

SWI-PS

Programming the SWI-PS to Control the Head Unit

Step 11.

Turn the vehicle ignition to

the ON position.

LED will ash to

indicate set version

number.

OFF

ACC

IGN

STRT

TEMP

IMPORTANT! Some steps of the programming instructions must be completed within a certain number of seconds following the

previous step. Review the complete instruction before beginning the programming sequence.

06-14-07

SWI-PS

Programming the SWI-PS to Control the Head Unit (cont.)

Step 22.

Release the button.

The LED will turn on

back on. Skip to Step

24.

Step 24.

If you need to program more buttons,

repeat step 20 for each additional audio

function on the steering wheel.

Once programming

is completed, wait 7

seconds. The LED will

ash three times indi-

cating end of program-

ming. The Interface will

then ash the version

number it was pro-

grammed for.

Step 21.

Within 7 seconds, press and

hold the button that is to be

learned on the steering wheel.

The LED will turn off

when the button has

been learned.

SWI-PS

After all buttons are

programmed

Program

remaining buttons

VOL

1. Volume Up

2. Volume Down

3. Mute

4. Track Up/Seek Up

5. Track Down/Seek Down

6. Source

7. Preset Up/Disc Up

8. Preset Down/Disc Down

9. Band

The SWI-PS must be programmed in the specic order shown below. If a function is not needed, it may be skipped.

SWI-PS

Step 23.

Within 7 seconds,

press and release the

programming/mode

button on the SWI-PS.

SWI-PS

The LED will ash

once and stay on.

This will indicate

that the function

has been skipped.

Skip to Step 20.

Step 20.

A. If the current function above is what you

need to program, proceed to step 21.

B. If the current function above is not needed,

proceed to step 23

Example: If you have a vehicle with only 3 functions, and you want to program Volume Up, Volume Down and Source. You will do

Step 21-22 twice, the rst time for Volume Up, the second time for Volume Down. Step 23 will be done 3 times to skip

Mute, Track Up and Track Down. Do Step 21-22 to program Source. After all 3 buttons have been programmed, you will

proceed to Step 24.

Testing the SWI-PS

Note: For Sony head units, please refer to the note below.

Test each Heater function of the steering wheel controls. The

TEMP and FAN should work properly. When testing the audio

controls, the left LED on the SWI-PS will ash indicating it is

sending a command. If any function does not work, repeat the

programming instructions (starting from Step 11) or refer to

Troubleshooting Guide.

VOL

TEMP

Sony Head Units only!: If the Volume and Track/

Seek settings are reversed, you need to program the head

unit to reverse the input. Please refer to the radio's Owners

Manual to change this feature for the wired remote.

06-14-07

Appendix A: Known Incompatible Vehicles

Vehicle

Make(s) Year(s) Model(s)

BMW All All with factory-activated cellular phones

All with 5-volt SWC data wire at the steering column

2002-2003 5-Series w/navigation

Mercedes-Benz All All vehicles

Toyota All-2003 Sienna

Volkswagen 2002-up All vehicles

Steering Wheel

Interface

Connect SWI white

wire to resistors

100

150

560

1000

1500

47 = yel, vio, blk

100 = brn, blk, brn

150 = brn, grn, brn

560 = grn, blu, brn

1000 = brn, blk, red

1500 = brn, grn, red

3900 = org, wht, red

5100 = grn, brn, red

Some vehicles have a seperate wire for each of the steering wheel buttons. Use this resistor kit for the steering wheel

push buttons that do not already have a resistor network connected to them. Examples are Nissan and Harley Davidson

motorcycles.

Connect a resistor to each side of a push button and connect the other ends of the resistor all together. Connect the SWI-

PS to these resistors. On the Harley Davidson, one button can be connected directly to the SWI-PS.

By putting two or more resistor in series, you can come up with additional values. Ex. 150 + 1000 + 1500 = 2650ohms.

Appendix B: Resistor Kit

Troubleshooting Guide

Working on a new or unlisted vehicle?

We are always looking for new vehicle information. If you’ve successfully completed the installation on a vehicle with

steering wheel controls, and the vehicle is not listed in these instructions or on our Website, contact us at

[email protected] so that we may add the information to the instructions.

Pacic Accessory Corporation

1502 S. Santa Fe St. • Santa Ana, CA 92705

[email protected] • www.pac-audio.com

No power / won’t go into programming mode:

• Check Red wire connection and fuse. Make sure INTERFACE is connected to switched +12volts, not constant +12volts.

• Make sure vehicle ignition is on.

The INTERFACE controls the stereo immediately without pressing any buttons on the steering wheel:

• During programming, press the buttons on the steering wheel rmly until the left LED turns off. Releasing the button too early

will cause the INTERFACE to send out a signal even when no buttons are pressed.

The INTERFACE controls the radio whenever the steering wheel is turned (mostly late 80’s early 90’s Honda/Acura).

• Program the INTERFACE for version #11.

When ever I program a new button the previous button does not work.

• You must program all buttons during programming. If you try to program another button, all previous button will be erased. You

will have to relearn all previous buttons again.

Indice

Altri manuali PAC Ricambi per automobili

PAC

PAC SWI-X Manuale utente

PAC

PAC SWI-X Manuale utente

Manuali Ricambi per automobili popolari di altre marche

Dakota Digital

Dakota Digital 650277 Manuale utente

bosal

bosal 037031 Manuale utente

Edelbrock

Edelbrock 66332 Manuale utente

Edelbrock

Edelbrock Honda XR400 Manuale del proprietario

Vintage Air

Vintage Air 571063 Manuale utente

Edelbrock

Edelbrock 70005 Manuale utente

GFB

GFB EX38 Manuale utente

Edelbrock

Edelbrock 65272 Manuale utente

bosal

bosal 028091 Manuale utente

Dodge

Dodge 8W-43 Guida rapida

ICI

ICI Magnum FBM10DGN Manuale utente

Volant Perfomance

Volant Perfomance 19435 Manuale utente

BENDIX

BENDIX GEN 4 GEN 5 ABS Manuale utente

Edelbrock

Edelbrock 72552 Manuale utente

Edelbrock

Edelbrock 70024 Manuale utente

Edelbrock

Edelbrock 6719 Manuale utente

Edelbrock

Edelbrock 5486 Manuale utente

Vintage Air

Vintage Air 571065 Manuale utente