Pamex FKL Manuale utente
WARNING
CAUTION !
1
IMPORTANT SAFETY INSTRUCTION
1. To preventdamage to thefinish, DO NOT use anyabrasives, sharp objects or harsh chemical
products containingalcohol, petroleum solvents, acidsor acetone to clean thislockset.
2. To preventdamage to thesensitive electronic components, DO NOT allow anyliquids to enter
lockset while installing or cleaning.
1. Do notattempt todisassemble any internal componentsof this locksetas this WILLvoid the
limited warranty.
2. Do notdrop or hit/strike thelockset as excessive shock may resultin permanent damage.
STRONGLYrecommended that you alwayscreate a written backup of the programming code
and individual usercodes. Please usethe last page of thisbooklet as yourreference.
5. For your Security, please remember to change this lockset's factory default programming code
to a PERSONAL programming code prior tonormal day to day useof this product(See Page28).
6. It isSTRONGLYrecommended thatyou use onlyALKALINE BATTERIES to operate this product.
3. Do notuse sharp objectsto press key buttons.
4. It is
CONTENTS
INSTALLATION INSTRUCTIONS
1. COMPONENTS
3. LATCHINSTALLATION
4. STRIKE PLATE INSTALLATION
5. LEVER DIRECTIONDETERMINATION
7-1. MOUNTING EXTERIORASSEMBLY
7-2. PREPARINGTO MOUNT INTERIORASSEMBLY
7-3. REMOVING DECORATIVE COVER
7-4. MOUNTING INTERIORASSEMBLY
7-5. BATTERY INSTALLATION
7-6. REINSTALL LEVER
8-1. EXCHANGE OFLEVER
8-2. EXCHANGE OFLEVER (REMOVALOF INSIDE LEVER)
8-3. EXCHANGE OFLEVER (REMOVALOF OUTSIDE LEVER)
2. DOOR PREPARATION 6
2
TEMPLATE 5
6-1. TO RESET DIRECTION OFINSIDE LEVER
6-2. TO RESET DIRECTION OFOUTSIDE LEVER
8-4. SWAPINSIDE AND OUTSIDELEVERS (REMOVALOF CYLINDER)
8-5. SWAPINSIDE AND OUTSIDELEVERS (ASSEMBLE OUTSIDELEVER)
8-6. SWAPINSIDE AND OUTSIDELEVERS (ASSEMBLE INSIDELEVER)
CONTENTS
MAIN OPERATING INSTRUCTIONS
SETUP MODE
1. CHANGE PROGRAMMINGCODE
2. ADD AUSER CODE
3. DELETE INDIVIDUALEXISTING USER CODE
5. DISABLE ALLTHE EXISTING USERCODES (VACATION MODE)
6. DISABLE BUTTONSOUND (MUTE MODE)
7. SETTING AUTO-LOCKTIME DELAY
8. RESTOREFACTORYSETTING
OPERATIONMODE
TROUBLESHOOTING GUIDELINE
DATARECORDS
4. DELETE ALLTHE EXISTING USERCODES AT ONCE
3
DECLARATION AND SAFETY STATEMENTS
1.TOACTIVATE AUTO-LOCKING(AUTOMATICRE-LOCKING)
2. TO OPEN(UNLOCK) THE DOOR
3. TO DEACTIVATE AUTO-LOCKING(AUTOMATICRE-LOCKING)
4
A
B
C
D
E
F
G
H
I
J
K
L
M
INSTALLATION INSTRUCTIONS
A. Key
B. Exterior Assembly
C. Mounting Plate
D. InteriorAssembly
E. DecorativeCover
F.Battery PackCover
G. Lever
H. 5/16''(7.8mm) Screw (2)
I. 1-1 /4''(32mm) Screw (2)
J. Latch
K. 6/8''(19.2mm) Wood Screw (4)
L. Strike
M. Dust Box
1. COMPONENTS
5
Fold here
Place on dooredge
51 45 40 35
Drill 1''(25mm) hole
at centerof door edge
2''
1-3/4'' 1-9/16'' 1-3/8''
O54mm(2-1/8'')
Backset 70mm(2-3/4'')
Backset 60mm(2-3/8'')
1. Removelever lock, ordo not install lever lockprior to paintingyour door.
2. Do not letany wateror liquid into the locksetduring installation process.
TEMPLATE
IMPORTANTBEFORE PROCEEDING
NOTE:MEASUREMENTS BELOW ARE JUST A GUIDELINE.Please measureyour door to determine
the exactcenter of your door edge.
6
54mm(2-1/8'')
25mm(1'')
60mm(2-3/8'') or 70mm(2-3/4'')
AB
DOOR PREPARATION
2. DOOR PREPARATION
Use Diagramof spade bit
here and notDrill bit
NOTE: Ifreplacing an existing lock orinstalling in a pre-drilled door, begin withpage 7.
Fold the template againstthe door edgeas shown inbelow illustration,mark and drilla pilot
hole for latch on dooredge, select backset(60mm or 70mm)to mark anddrill a pilothole for
selected backset on door face.(It is recommended to markcenterline of the hole ondoor about
36 inches (914mm)above the floor. )
7
60mm(2-3/8'')
70mm(2-3/4'')
INSTALLATION INSTRUCTIONS
3. LATCH INSTALLATION
A. Pull thedrive-shaft backwardfor adjustmentto 70mm(2-3/4'').
B. Push thedrive-shaft forwardfor adjustmentto 60mm(2-3/8'').
Drive-shaft
Drive-shaft
8
INSTALLATION INSTRUCTIONS
A. Insert thelatch intothe latch hole.Using the faceplate as apattern, TRACEa line alongthe out
edge of thefaceplate andchisel a 4mm(1/8") slot inthe markedout area. Face plate shouldfit
flush with dooredge.
B. Insert thelatch into the latch holeand fastenwith screws.
Show pencil marking outeredge of latch faceplate with Dotted lined
directional arrows asyou do not justcarve out the screw holes
AB
3. LATCH INSTALLATION
Indice
Altri manuali Pamex Serratura della porta
