Panasonic WV-Q122E Manuale utente

Before attempting to connect or operate this product,

please read these instructions carefully and save this manual for future use.

The model number is abbreviated in some descriptions in this manual.

Wall Mount Bracket

Operating Instructions

Model No. WV-Q122E

The camera in the illustration is separately sold.

-2-

Front Cable Exit

1. Preparations

Specify the bracket fixing location, and then put in

four anchor bolts, or drill four bolt holes on the

installation surface. Refer to Dimensions on page 7.

2. Cable Bushing

Fit the supplied cable bushing into the front cable

exit of the bracket.

3. Cable Route

Route the connection cables from the front cable

exit through the bracket, and pull them out of the

pipe mouth.

4. Fixing Bracket

Fix the bracket to the wall using appropriate hard-

ware (not supplied): bolts and nuts, anchor bolts

and nuts, or the like.



Mark hole positions

Cable Bushing

Fixing Hardware

(Locally Procured)

■Introduction

This bracket is used for mounting the colour camera WV-CW960 or WV-CW964 onto a wall.

There are two ways of cable exit available from the front or rear of the bracket.

Precautions

•Make sure that the place you are installing the camera is strong enough to support it. If it is not strong enough, then the cam-

era may fall and hurt someone.

•The following steps of installation and connection work should be done by qualified service personnel or system installers

and should conform to all local codes.

•Be sure to turn the power off before installation and connection.

•Do not install the camera near the air outlet of an air conditioner.

-3-

5. Disassembly of Camera

(1) Remove the upper base from the camera by

loosening 3 screws. The screws that are

removed need to be used during reassembly.

Be careful to not lose them. Turn the upper base

and separate it.

* Special screw (mounting screw): Use a hexa-

gon wrench for the hexagon screw (M6).

(2) Remove the attachment pipe from the upper

base by loosening 4 screws.

* Special screw (mounting screw): Use a hexa-

gon wrench for the hexagon screw (M6).

6. Setting Switches

Refer to DIP SWITCH SETTINGS in the manual

included with the camera.

7. Cable Connection

Refer to CONNECTIONS in the manual included

with the camera.

Warning: Seal the cables with plastic or rubber

tape to prevent it from being exposed.

8. Mounting Upper Base

Fix the upper base to the bracket.

• Fasten 4 screws (the screws that were removed in

step (2) of “5. Disassembly of Camera”) making

sure that “REAR” engraved on the upper base faces

the wall.

9. Waterproofing

Fill the front cable exit with sealant.

Warning: Carefully apply the sealing so that water

or moisture cannot get inside. If water gets

inside the camera it could cause a shock or fire.

Also, if moisture gets inside the camera it could

cause the dome to become foggy.

10. Mounting Camera

(1) Aim the START arrow at the bent portion of the

leaf spring on top of the camera.

START

Sealant

Cable Bushing

Outside

Inside the bracket

Cables

Upper Base

Attachment Pipe

Camera Fixing Screw

Upper Base

Bending Leaf Spring

Camera

-4-

(2) Be sure to hook the fall prevention wire to the

bracket.

(3) Fix the camera to the upper base.

• Move the camera up so that its guide pins fit into

the guide holes of the upper base.

• Turn the camera counter-clockwise to the end,

viewed from the bottom.

• Fasten 3 screws (the screws that were removed

in step (1) of “5. Disassembly of Camera”).

Caution: Tighten the three (3) mounting screws for

the upper base.

Recommended torque: Approximately 2.45 N/m

{24 kgf cm}

Poorly tightened screws may result in water

leaking into the camera or possible fire.

Fall Prevention Wire

Upper Base

Camera

-5-

Rear Cable Exit

1. Preparations

Specify the bracket fixing location, and then put in

four anchor bolts (not supplied), or drill four bolt

holes on the surface.

Remember that a cable access hole is necessary on

the wall in this case.

Refer to Dimensions on page 7.

2. Rear Cable Exit

(1) Remove the rear plate, and then punch out the

cable exit on it.

(2) Fit the supplied blank bushing into the front

cable exit of the bracket.

(3) Fit the supplied cable bushing into the rear cable

exit of the plate.

(4) Replace the rear plate to the bracket fastening

four screws.

3. Cable Routing

Route the connection cables from the rear cable exit

through the bracket, and pull them out of the pipe

mouth.

4. Waterproofing

Fill the rear cable exit with sealant.

5. Fixing Bracket

Fix the bracket to the wall using appropriate hard-

ware (not supplied): bolts and nuts, anchor bolts

and nuts, or the like.



Cable Access Hole

on the wall

Front Cable Exit

(Not Used) Rear Cable Exit

Rear Plate

Blank Bushing Cable Bushing

Fixing Hardware

(Locally Procured)

Sealant

Cable Bushing

Outside

Inside the Bracket

Cables

Mark hole positions

-6-

6. Disassembly of Camera

(1) Remove the upper base from the camera by

loosening 3 screws. The screws that are

removed need to be used during reassembly. Be

careful to not lose them. Turn the upper base

and separate it.

* Special screw (mounting screw): Use a hexa-

gon wrench for the hexagon screw (M6).

(2) Remove the attachment pipe from the upper

base by loosening 4 screws.

* Special screw (mounting screw): Use a hexa-

gon wrench for the hexagon screw (M6).

7. Setting Switches

Refer to DIP SWITCH SETTINGS in the manual

included with the camera.

8. Cable Connection

Refer to CONNECTIONS in the manual included

with the camera.

Warning: Seal the cables with plastic or rubber

tape to prevent it from being exposed.

9. Mounting Upper Base

Fix the upper base to the bracket.

• Fasten 4 screws (the screws that were removed in

step (2) of “6. Disassembly of Camera”) making

sure that “REAR” engraved on the upper base faces

the wall.

10. Mounting Camera

(1) Aim the START arrow at the bent portion of the

leaf spring on top of the camera.

(2) Be sure to hook the fall prevention wire to the

bracket.

(3) Fix the camera to the upper base.

• Move the camera up so that its guide pins fit into

the guide holes of the upper base.

• Turn the camera counter-clockwise to the end,

viewed from the bottom.

• Fasten 3 screws (the screws that were removed

in step (1) of “6. Disassembly of Camera”).

Caution: Tighten the three (3) mounting screws for

the upper base.

Recommended torque: Approximately 2.45 N/m

{24 kgf cm}

Poorly tightened screws may result in water

leaking into the camera or possible fire.

START

Upper Base

Attachment Pipe

Camera Fixing Screw

Upper Base

Bending Leaf Spring

Fall Prevention Wire

Upper Base

Camera

-7-

■Specifications

Dimensions: 111.5(W) x 210.5(H) x 269(D) mm

Weight: 2 kg approx.

Weight and dimensions indicated are approximate.

Specifications are subject to change without notice.

■Accessories

Operating Instructions (this manual) ............................. 1 pc.

The following items are for installation.

Camera Fixing Screw (Hexagon screw (M6)) ...............4 pcs.

Cable Bushing ...............................................................1 pc.

Blank Bushing................................................................1 pc.

Ø58

269

（111.5）

180

(210.5)

4-Ø10

240

Unit: mm

(50)

(90)

Ø25.4

■Dimensions

Fall Prevention

Wire Hook

Rear Cable Exit

(Punch out the hole when using)

Camera Fixing

Screw Hole x4

Front Cable Exit

AM1105-2010 3TR004263CAA Printed in Japan

Indice

Altri manuali Panasonic Accessori per fotocamere

Panasonic

Panasonic Lumix DMW-MCTZ10 Manuale utente

Panasonic

Panasonic AJ-HVF20P Manuale utente

Panasonic

Panasonic VW-BTA1 Manuale utente

Panasonic

Panasonic LC-R063R4P Manuale utente

Panasonic

Panasonic WV-Q100A Manuale utente

Panasonic

Panasonic WV-Q108AE Manuale utente

Panasonic

Panasonic H-FS45150 Manuale utente

Panasonic

Panasonic AW-LK50 Manuale utente

Panasonic

Panasonic WV-7110AE Manuale utente

Panasonic

Panasonic WV-QCL500-S Manuale utente

Panasonic

Panasonic WV-7150D Manuale utente

Panasonic

Panasonic AW-CH600 Manuale utente

Panasonic

Panasonic FL360 - DMW - Hot-shoe clip-on Flash Manuale utente

Panasonic

Panasonic ET-DLE105 Manuale utente

Panasonic

Panasonic WV7230 - CCTV ACCESSORIES Manuale utente

Panasonic

Panasonic AW- PH350 Manuale utente

Panasonic

Panasonic AW-PB504N Manuale utente

Panasonic

Panasonic WV-Q167 Manuale utente

Panasonic

Panasonic PUM8 Manuale utente

Panasonic

Panasonic Lumix H-PS14042 Manuale utente

Panasonic

Panasonic WVPS154 - CAMERA DRIVE UNIT Manuale utente

Panasonic

Panasonic WV-Q161 Manuale utente

Panasonic

Panasonic H-NS043 Manuale utente

Panasonic

Panasonic WVLZ6115 - ZOOM LENS Manuale utente

Manuali Accessori per fotocamere popolari di altre marche

Viltrox

Viltrox EF-NEX Istruzioni per l'installazione

Calumet

Calumet 7100 Series CK7114 Manuale utente

Ropox

Ropox 4Single Series Manuale utente

Cambo

Cambo Wide DS Digital Series Istruzioni operative

Samsung

Samsung SHG-120 Manuale utente

Ryobi

Ryobi BPL-1820 Manuale operativo

Aegis

Aegis ABL-36020P Manuale utente

Pentax

Pentax Data Back Fc Manuale utente

Fantasea

Fantasea EyeGrabber F Series Manuale utente

Honeywell

Honeywell HDZ20HD Manuale utente

EGO

EGO BA1400T Manuale utente

Sima

Sima SRW-62 Manuale utente

Shape

Shape A7SSMKIT Manuale utente

Slide Kamera

Slide Kamera HST-2 Manuale utente

Power works

Power works 2902613 Manuale utente

SES

SES SE-2047-2 Manuale utente

Olympus

Olympus PT-EP05L Manuale utente

Starlite

Starlite OctoDome nxt Manuale utente