Panasonic ET-MDN12G10 Manuale utente

Thank you for purchasing this Panasonic product.

■Before using this product, please read these “Operating Instructions” and

the “Operating Instructions” of the projector carefully and save the manuals

for future use.

■Before using this product, be sure to read “Read this  rst!” (xpage 3).

DPQX1184ZC

Printed in China

Interface Board for 12G-SDI Commercial Use

Operating Instructions

ENGLISH

Model No. ET-MDN12G10

ENGLISH

FRANÇAIS

2 - ENGLISH

Contents

Read this rst! 3

Precautions for use 4

Supported projector 4

About the handling of the product 4

Disposal 4

Accessories 4

Part names and functions 5

Installing the Interface Board 5

Before installing or removing the Interface Board 5

How to install the Interface Board 6

How to remove the Interface Board 7

Specications 8

ENGLISH - 3

Read this rst!

WARNING:

Do not spill water on this product or allow this product to get wet.

Doing so may cause re, electric shock, or malfunction due to short circuit

or overheating.

fDo not place a container with liquid close to this product.

fConsult your dealer when liquid such as water is spilled on this

product.

Do not place the supplied screws in a location that a child can reach.

Accidentally swallowing them can cause a physical harm.

fSeek a medical advice immediately if a child might have swallowed a

screw.

Do not disassemble or modify.

Doing so may cause electric shock or re. It may also cause a malfunction.

CAUTION:

Do not place this product in a location with excessive humidity or

dust, or in a location exposed to oil smoke or steam.

Doing so may cause re or electric shock.

Do not place this product in extremely hot location.

Doing so may deteriorate the part, or may cause re.

fDo not install or store in a location with direct sunlight or close to the

heating device, etc.

Turn o󰀨 the power and disconnect the power plug from the outlet

when installing or removing this product to/from the projector.

Failure to do so may cause electric shock.

Precautions for use

4 - ENGLISH

Precautions for use

This product is a 12G-SDI signal compatible interface board for use installed

in a Panasonic Connect Co., Ltd. projector.

Supported projector

PT-RQ32K series, PT-RQ13K series, PT-RQ22K series

(As of March 2019)

Note

fProducts other than the above may also be supported. Check the Operating Instructions of

your projector.

fIf the main version of the rmware of the PT-RQ32K or PT-RQ13K is less than 3.00, this

interface board cannot be used. Update the rmware to the latest version before use. Check

the update procedure by accessing the page containing the latest information on the rmware

at the website (https://panasonic.net/cns/projector/pass/).

About the handling of the product

rDo not touch the connector section of the Interface Board

directly with your hands.

The component may be damaged by the static electricity. Handle this

product after removing the static in your body by touching the surrounding

metal, etc.

Disposal

To dispose of the product, ask your local authorities or dealer for correct

methods of disposal.

Accessories

Make sure that the following accessories are provided with your product.

Numbers enclosed in < > show the number of accessories.

Screw <4>

(XSB3+8FN)

Attention

fAppropriately discard the packaging material after unpacking the product.

fFor missing accessories, consult your dealer.

fStore small parts in an appropriate manner, and keep them away from small children.

Installing the Interface Board

ENGLISH - 5

Note

fThe supplied screws are spare. Use them when a screw to x the slot cover of the projector

is lost.

fThe model numbers of accessories are subject to change without prior notice.

Part names and functions

5 21 43 5

1 <SDI 1 IN> terminal

This is a terminal to input SDI signals

(SD-SDI / HD-SDI / 3G-SDI / 6G-SDI /

12G-SDI).

2 <SDI 2 IN/1 OUT> terminal

This is a terminal to input SDI signals

(SD-SDI / HD-SDI / 3G-SDI). It is also

an active through terminal to output the

SDI signals (SD-SDI / HD-SDI / 3G-SDI

/ 6G-SDI / 12G-SDI) input to the <SDI 1

IN> terminal.

3 <SDI 3 IN> terminal

This is a terminal to input SDI signals

(SD-SDI / HD-SDI / 3G-SDI / 6G-SDI /

12G-SDI).

4 <SDI 4 IN/3 OUT> terminal

This is a terminal to input SDI signals

(SD-SDI / HD-SDI / 3G-SDI). It is also

an active through terminal to output the

SDI signals (SD-SDI / HD-SDI / 3G-SDI

/ 6G-SDI / 12G-SDI) input to the <SDI 3

IN> terminal.

5 Handle

Note

fThe <SDI 2 IN/1 OUT> terminal and <SDI 4 IN/3 OUT> terminal do not support the input of

6G-SDI signals and 12G-SDI signals.

fTo use the <SDI 2 IN/1 OUT> terminal and <SDI 4 IN/3 OUT> terminal as output terminals,

you need to change the settings of the projector. Check the Operating Instructions of your

projector.

Installing the Interface Board

It is recommended to ask a qualied technician to install or remove the

Interface Board to a projector. A malfunction may occur due to static

electricity. Consult your dealer.

Before installing or removing the Interface Board

fAlways turn o󰀨 the power of the projector before installing or removing the

Interface Board.

gMake sure to follow the procedure described in the Operating

Instructions of your projector when turning o󰀨 the power.

Installing the Interface Board

6 - ENGLISH

fDo not touch the connector section of the Interface Board directly with your

hands.

gThe component may be damaged by the static electricity.

fRemove the static charge from your body by touching the surrounding

metal, etc., in advance to prevent the static electricity damage.

fTake care not to get injured when installing or removing the Interface

Board.

gHands may be injured by the opening of the blank slot of the projector or

the edge of the bracket of the Interface Board.

fWhen installing the Interface Board to the slot, insert it into the connector

straight and slowly.

gIt may not operate or cause malfunction if it is not correctly installed.

fInstall and use this interface board in one of the <SLOT 1> and <SLOT 2>

slots. If this interface board is installed both in <SLOT 1> and in <SLOT

2>, only the one installed in <SLOT 1> can be used.

How to install the Interface Board

Screws (4 locations) Screws (4 locations)

Salient

Guide groove

Slot cover

Fig. 1 Fig. 2 Fig. 3

1) Remove the slot cover. (Fig. 1)

fRemove the four screws xing the slot cover of the projector by

rotating counterclockwise with a Phillips screwdriver. The removed

screws are used to x the Interface Board.

fWhen removing the fourth screw, hold the slot cover with your hand so

it will not fall.

fTo replace from other Interface Board, remove the Interface Board

following the procedure in “How to remove the Interface Board”

(xpage 7).

Installing the Interface Board

ENGLISH - 7

2) Install the Interface Board to the projector. (Fig. 2)

fInsert the guide groove of the Interface Board aligned to the salient of

the slot. Insert the bracket rmly all the way in.

3) Fix the Interface Board. (Fig. 3)

fTighten and x with the four screws removed in Step 1).

Attention

fThe removed slot cover is required when the unnecessary Interface Board is removed. Store

it so it can be attached in the future.

How to remove the Interface Board

Handle

Fig. 1

1) Remove the Interface Board. (Fig. 1)

fRemove the four screws xing the Interface Board by rotating

counterclockwise with a Phillips screwdriver. The removed screws are

used to x the slot cover.

fHold the handle of the Interface Board and remove it slowly.

2) Attach the slot cover.

fAttach the stored slot cover to the blank slot, and tighten and x with

the four screws removed in Step 1).

Attention

fAlways attach the slot cover on the blank slot.

fStore the removed Interface Board inside an antistatic bag.

Specications

8 - ENGLISH

Specications

Compatible slot SLOT NX specication

Connection

terminals /

supported

signals

Inputs

BNC 4 lines

(<SDI 1 IN> terminal, <SDI 2 IN/1 OUT> terminal, <SDI 3 IN>

terminal, <SDI 4 IN/3 OUT> terminal)

Single link SD-SDI signal, SMPTE ST 259 standard compliant

Single link HD-SDI signal, SMPTE ST 292 standard compliant

Single link 3G-SDI signal, SMPTE ST 424 and 425-2 standards

compliant

Single link 6G-SDI signal, SMPTE ST 2081-1 and 2081-10

standards compliant

Supported by <SDI 1 IN> terminal and <SDI 3 IN> terminal only

Single link 12G-SDI signal, SMPTE ST 2082-1 and 2082-10

standards compliant

Supported by <SDI 1 IN> terminal and <SDI 3 IN> terminal only

Dual link HD-SDI signal, SMPTE ST 372 standard compliant

<SDI 1 IN> terminal: Link A signal /

<SDI 3 IN> terminal: Link B signal

Dual link 3G-SDI signal, SMPTE ST 425-3 standard compliant

<SDI 1 IN> terminal: Link 1 signal /

<SDI 3 IN> terminal: Link 2 signal

Dual link 6G-SDI signal, SMPTE ST 2081-11 standard compliant

<SDI 1 IN> terminal: Link 1 signal /

<SDI 3 IN> terminal: Link 2 signal

Quad link HD-SDI signal

<SDI 1 IN> terminal: Link 1 signal /

<SDI 2 IN/1 OUT> terminal: Link 2 signal /

<SDI 3 IN> terminal: Link 3 signal /

<SDI 4 IN/3 OUT> terminal: Link 4 signal

Quad link 3G-SDI signal, SMPTE ST 425-5 standard compliant

<SDI 1 IN> terminal: Link 1 signal /

<SDI 2 IN/1 OUT> terminal: Link 2 signal /

<SDI 3 IN> terminal: Link 3 signal /

<SDI 4 IN/3 OUT> terminal: Link 4 signal

Outputs

BNC 2 line (also functions as input terminal)

(<SDI 2 IN/1 OUT> terminal, <SDI 4 IN/3 OUT> terminal)

Performs active through output of the signals input to the <SDI 1

IN> terminal and <SDI 3 IN> terminal.

Dimensions

Width 151 mm (5-15/16")

Height 38.5 mm (1-17/32")

Depth 142 mm (5-19/32")

Weight 400 ] (14.1 ozs.)

Specications

ENGLISH - 9

Note

f“SLOT NX” is a name of the slot unique to Panasonic Connect Co., Ltd. supporting the signal

input for the 4K image.

fThe video signal that can actually display will vary depending on the projector that the

Interface Board is installed. For details, refer to the Operating Instructions of your projector.

fWhen the projector is in the standby state, signals are not output from the <SDI 2 IN/1 OUT>

terminal and <SDI 4 IN/3 OUT> terminal.

fTo ensure images are transmitted correctly, use 5C-FB or higher (5C-FB, 7C-FB, etc.), Belden

1694A or higher, or Canare Electric L-5.5CUHD for the connection cable. Furthermore, the

maximum lengths of cables that can be used are as follows. However, these maximum cable

lengths are provided as a guide, and are not a guarantee of transmission distances.

gSD-SDI signal, HD-SDI signal, and 3G-SDI signal: 150 m

g6G-SDI signal: 80 m (110 m if L-5.5CUHD is used.)

gWhen 12G-SDI, di󰀨ers depending on the setting of [Display Options] menu → [SLOT IN] →

[SDI Mode] of the projector.

When [SDI Mode] is set to [Input], 50 m (100 m if L-5.5CUHD is used.)

When [SDI Mode] is set to [Output], 50 m (90 m if L-5.5CUHD is used.)

fWhen [Display Options] menu → [SLOT IN] → [SDI Mode] of the projector is set to [Output],

attach a terminating resistor (75 Ω) to the terminal to which a device is not connected as an

output destination.

fFor the BNC connector of the connection cable, use one that supports the coaxial cable and

types of signal to be used.

10 - ENGLISH

English

Manufactured by:

Panasonic Connect Co., Ltd.

4-1-62 Minoshima, Hakata-ku, Fukuoka 812-8531,

Japan

Importer:

Panasonic Connect Europe GmbH

Authorized Representative in EU:

Panasonic Testing Centre

Winsbergring 15, 22525 Hamburg, Germany

Importer for UK;

Panasonic Connect UK,

a branch of Panasonic Connect

Europe GmbH,

Maxis 2, Western Road, Bracknell,

Berkshire, RG12 1RT

Français

Fabriqué par:

Panasonic Connect Co., Ltd.

4-1-62 Minoshima, Hakata-ku, Fukuoka 812-8531,

Japon

Importateur :

Panasonic Connect Europe GmbH

Représentant autorisé dans l’UE :

Panasonic Testing Centre

Winsbergring 15, 22525 Hambourg, Allemagne

Español

Fabricado por:

Panasonic Connect Co., Ltd.

4-1-62 Minoshima, Hakata-ku, Fukuoka 812-8531,

Japón

Importador:

Panasonic Connect Europe GmbH

Representante Autorizado para la UE:

Panasonic Testing Centre

Winsbergring 15, 22525 Hamburgo, Alemania

Deutsch

Hergestellt von:

Panasonic Connect Co., Ltd.

4-1-62 Minoshima, Hakata-ku, Fukuoka 812-8531,

Japan

Importeur:

Panasonic Connect Europe GmbH

Vertretungsberechtigter in der EU:

Panasonic Testing Centre

Winsbergring 15, 22525 Hamburg, Deutschland

Italiano

Fabbricato da:

Panasonic Connect Co., Ltd.

4-1-62 Minoshima, Hakata-ku, Fukuoka 812-8531,

Giappone

Importatore:

Panasonic Connect Europe GmbH

Rappresentante autorizzato nell’UE:

Panasonic Testing Centre

Winsbergring 15, 22525 Amburgo, Germania

Български

Производител:

Panasonic Connect Co., Ltd.

4-1-62 Minoshima, Hakata-ku, Fukuoka 812-8531,

Япония

Вносител:

Panasonic Connect Europe GmbH

Упълномощен представител в ЕС:

Panasonic Testing Centre

Winsbergring 15, 22525 Hamburg, Германия

Čeština

Vyrobil:

Panasonic Connect Co., Ltd.

4-1-62 Minoshima, Hakata-ku, Fukuoka 812-8531,

Japonsko

Dovozce:

Panasonic Connect Europe GmbH

Oprávněný zástupce v EU:

Panasonic Testing Centre

Winsbergring 15, 22525 Hamburk, Německo

Dansk

Fremstillet af:

Panasonic Connect Co., Ltd.

4-1-62 Minoshima, Hakata-ku, Fukuoka 812-8531,

Japan

Importør:

Panasonic Connect Europe GmbH

Autoriseret repræsentant i EU:

Panasonic Testing Centre

Winsbergring 15, 22525 Hamburg, Tyskland

Indice

Altri manuali Panasonic Hardware per computer

Panasonic

Panasonic KX-TVM50 Manuale utente

Panasonic

Panasonic UB-5335 Manuale utente

Panasonic

Panasonic KX-TVP120C Manuale utente

Panasonic

Panasonic UP0KG8D Manuale utente

Panasonic

Panasonic 2SA2009G Manuale utente

Panasonic

Panasonic 2SB1679 Manuale utente

Panasonic

Panasonic ET-MCYDV100 Manuale utente

Panasonic

Panasonic 2SA2078 Manuale utente

Panasonic

Panasonic WZ-TDADP Manuale utente

Panasonic

Panasonic KX-W1000 Manuale utente

Panasonic

Panasonic PanaXSeries MN1030 Series Manuale utente

Panasonic

Panasonic AW-360B10 Manuale utente

Panasonic

Panasonic Panaboard UB-5310 Manuale utente

Panasonic

Panasonic CF-BAB2048U Manuale utente

Panasonic

Panasonic ERB RD Manuale utente

Panasonic

Panasonic UP0KG8DG Manuale utente

Panasonic

Panasonic AW-PB307P Manuale utente

Panasonic

Panasonic WZ-AESAD Manuale utente

Panasonic

Panasonic 2SB1321A Manuale utente

Panasonic

Panasonic 2SC4691G Manuale utente

Panasonic

Panasonic 2SC3312 Manuale utente

Panasonic

Panasonic TY-SB01F Manuale utente

Panasonic

Panasonic PanaXSeries MN103S65G Manuale utente

Panasonic

Panasonic 2SC3757 Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente

Advantech

Advantech ASMB-935 Series Manuale utente